Commit Graph

26 Commits

Author SHA1 Message Date
Jonathan Lemon
3ceb25205d . Add structure definition for microcode download.
Submitted by: Marko Zec <zec@tel.fer.hr>

  . Add some PCI chip revision entries.
  . Make size of txcb dependent on pointer size rather than arch #define
2001-10-25 05:25:58 +00:00
Jonathan Lemon
00c4116b3e Systems based on the ICH2/ICH2-M chip from Intel have a defect where
the chip can cause a PCI protocol violation in under certain scenarios.
The workaround is to rewrite the EEPROM to disable Dynamic Standby Mode.

Once the EEPROM is rewritten, the system needs to be rebooted in order
to pick up the new settings.

This has been tested on several ICH2/ICH2-M systems, found in 815E based
boards, and usually identified by the presence of the 82562 ET/EM PHY.

Thanks to: Mike Tansca, Paul Saab for samples of the problematic boards.
2001-08-27 16:07:12 +00:00
Jonathan Lemon
dedabebf33 Use " |= " to enable special media handling for fxp with no MII, instead
of " &= ".  Also change the MII PHY device mask to check the correct bits.

Cookie to:	Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Pointy hat to:	me
2001-05-15 18:52:40 +00:00
Jonathan Lemon
e310a419c0 Add a few more register definitions. 2001-05-12 23:59:48 +00:00
Jonathan Lemon
3bd07cfd43 Add some performance features to the fxp driver. If the chip is not
a 82557 (e.g.: a newer chip) then:

   + enable MWI, if the PCI configuration indicates the system supports it
   + enable usage of extended TxCB, for better performance
   + enable hardware flow control.  FC frames will be passed up to the
     host only if promiscuous mode is enabled.
2001-03-14 19:50:35 +00:00
Jonathan Lemon
f7788e8e9f Convert the fxp driver to miibus, which involves ripping out the PHY
logic and media bits.  Support for Intel PHYs can now be found in
dev/mii/inphy.c.

Clean up the driver, and add various 82558 and 82559 specific bits.
2001-03-12 21:30:52 +00:00
Bill Paul
b2f5cb03e7 Add the PCI device ID for the on-board ethernet controllers on the
Intel 815E motherboard, which I believe is an i82562. Seems to work
just fine with the fxp driver.
2000-09-21 20:01:57 +00:00
David Greenman
55ce7b5117 Added support for the i82559ER (10/100Mbps NIC for embedded applications).
Product device ID provided by:	Les Biffle <les@ns3.safety.net>
2000-06-18 10:26:09 +00:00
Andrew Gallatin
4fc1dda91d Make the fxp driver work on alpha, rather than panic the machine on boot
and/or when using the card.

o Convert the driver to using bus_space.  This allows alphas with
fxp's to boot, rather than panic'ing because rman_get_virtual()
doesn't really return a virtual address on alphas.

o Fix an alpha unaligned access error caused by some misfeature of
gcc/egcs: if link_addr & rbd_addr in the fxp_rfa struct are 32 bit
quantities, egcs will assume they are naturally aligned. So it will do
a ldl & some shifty/masky to twiddle 16 bit values in fxp_lwcopy().
However, if they are 16-bit aligned, the ldl will actually be done on
a 16-bit aligned value & we will panic with an unaligned access
error... Changing their definition to an array of chars seems to fix
this.  I obtained this from NetBSD.

I've tested this on both i386 & alpha.
1999-09-30 19:03:12 +00:00
Peter Wemm
dd68ef1623 Recognise the new 82559 chip id as used on the InBusiness 10/100 adapter.
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99).  The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by:	Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
1999-09-06 06:15:18 +00:00
Peter Wemm
c3aac50f28 $Id$ -> $FreeBSD$ 1999-08-28 01:08:13 +00:00
Julian Elischer
da15ec8bf7 Define more registers and fix incorrect (but unused) register bit definitions. 1999-02-11 23:41:21 +00:00
Julian Elischer
f1bf08c22e Define more registers in the PHY unit and use them to report back
the result of the media auto negotiation.

Reviewed by: David Greenman <dg@freebsd.org>
1999-02-11 21:47:10 +00:00
Bruce Evans
a09bee1aa8 Fixed pedantic semantics errors (bitfields not of type int, signed int
or unsigned int (this doesn't change the struct layout, size or
alignment in any of the files changed in this commit, at least for
gcc on i386's.  Using bitfields of type u_char may affect size and
alignment but not packing)).
1998-06-08 09:47:47 +00:00
David Greenman
9292429115 Added support for the 82553 and 'B' 82555 PHY. 1998-03-03 14:19:09 +00:00
David Greenman
397f9dfe26 Work around a bug in the 82557 NIC where the receiver will lock up
if it is in 10Mbps mode and gets certain types of garbage prior to
the packet header. The work-around involves reprogramming the
multicast filter if nothing is received in some number of seconds
(currently set at 15). As a side effect, implemented complete support
for multicasting rather than the previous 'receive all multicasts'
hack, since we now have the ability to program the filter table.
Fixed a serious bug which crept in with the timeout() changes;
the cookie was only saved on the first timeout() call in fxp_init()
and wasn't updated in the most common place in fxp_stats_update()
when the timeout was rescheduled. This bug would have resulted in
an eventual panic if fxp_stop() was called (which happens when any
interface flags are changed, for example).
Fixed a bug in Alpha support that would have caused the TxCB
descriptor chain to span a page boundry, causing serious problems
if the pages didn't happen to be contiguous.
Removed some gratuitous bit masking that was left over from an
older implementation.
Fixed a bug where too much was copied from the configuration
template, spilling over into memory that followed it.
Fixed handling of if_timer...it was cleared too early in some cases.
1997-09-29 11:27:43 +00:00
David Greenman
ba8c6fd534 Changes to support NetBSD and the new ifmedia extensions.
Submitted by:	Jason Thorpe <thorpej@netbsd.org>
1997-09-05 10:23:58 +00:00
David Greenman
854d14213e Added support for the Intel 82555 PHY chip which is being used on newer
Pro/100B cards. Full duplex should work now, although it hasn't been
tested.
1997-06-13 22:34:52 +00:00
David Greenman
6ebc315326 Added support for newer cards that have the DP83840A PHY chip.
Fixed a bug in fxp_mdi_write - a hex number was missing a preceding 0x
and this was causing the routine to not wait for a PHY write to complete.
Added support for link0, link1, and link2 flags to toggle auto-
negotiation, 10/100, and half/full duplex:

link0	disable auto-negotiation

	When set, these flags then have meaning:

	-link1	10Mbps
	link1	100Mbps
	-link2	half duplex
	link2	full duplex

...needs a manual page.
1997-03-21 08:00:13 +00:00
David Greenman
dccee1a193 Fixed two deficiencies in the driver that have existed since it was
written:

1) Full duplex mode is now supported (and works!)
2) The 10Mbps-only PCI Pro/10 should now work (untested, however)

Thanks to Justin Gibbs for providing a PCI bus analyzer trace while the
Intel Windows driver was configuring the board...this made it possible
to figure out the mystery bit that I wasn't setting in the PHY for full
duplex to work.
1997-03-17 11:08:16 +00:00
Peter Wemm
6875d25465 Back out part 1 of the MCFH that changed $Id$ to $FreeBSD$. We are not
ready for it yet.
1997-02-22 09:48:43 +00:00
David Greenman
33d14d8671 Do "selective" reset rather than full reset...the manual specifically
says not to do the full reset because it can lock up the PCI bus if the
chip is active. Added various PORT command definitions to facilitate
this.
1997-02-04 10:53:12 +00:00
Jordan K. Hubbard
1130b656e5 Make the long-awaited change from $Id$ to $FreeBSD$
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.

Boy, I'm glad we're not using sup anymore.  This update would have been
insane otherwise.
1997-01-14 07:20:47 +00:00
David Greenman
58b248e254 Removed sections 3 and 4 from my copyright. 1996-04-08 01:31:42 +00:00
David Greenman
23a0ed7c08 Increased the number of Tx segments from 13 to 29 to reduce the need to
recopy to near zero. Wrote the necessary code to recopy the mbuf chain
into another buffer if there are too many mbufs in the chain.
1995-12-05 11:49:55 +00:00
David Greenman
a17c678ed2 Device driver for Intel Pro/100 PCI Fast Ethernet controller. 1995-11-28 23:55:26 +00:00