subclass, progif and revid. While these are typically read
only fields, they aren't always read-only. progif is writable
for ata devices, for example. It does no harm when they are
read only, and helps when they aren't.
to try to allocate things on my parent can be taken out. It duplicates code.
Also, add comment about why the power state stuff is here (type 2
devices don't participate in the power state save/restore due to
larger Bx issues).
chattiness was left in for debugging, but now that nearly all of the
problems relating to the changes have been fixed, it is only annoying. It
is still available via bootverbose.
Prodded by: jhb
threatened in rev.1.10 of usr.sbin/kgmon/kgmon.c more than 2 years ago.
kgmon has been recovering from the missing initialization for too
long, but the fixup there is ifdefed for i386's and shouldn't be
needed for other arches.
high resolution kernel profiling (options GUPROF. "U" in GUPROF stands
for microseconds resolution, but the resolution is now smaller than 1
nanosecond on multi-GHz machines and the accuracy is heading towards
1 nanosecond too). Arches that support GUPROF must now provide certain
macros for the calibration. GUPROF is now only supported for i386's,
so the absence of the new macros for other arches doesn't break anything
that wasn't already broken. amd64's have uncommitted support for
GUPROF, and sparc64's have support that seems to be complete except
here (there was an #error for non-i386 cases; now there are undefined
macros).
Changed the asms a little:
- declare them as __volatile. They must not be moved, and exporting a
label across asms is technically incorrect, so try harder to stop gcc
moving them.
- don't put the non-clobbered register "bx" in the clobber list. The
clobber lists are still more conservative than necessary.
- drop the non-support for gcc-1. It just gave a better error message,
and this is not useful since compiling with gcc-1 would cause thousands
of worse error messages.
- drop the support for aout.
because VLAN hardware features are enabled in em(4) by default.
Note: Currently vlan(4) has a bug that it consults
if_capabilities, not if_capenable. This will be fixed
after all the network drivers set VLAN bits in
if_capenable properly.
- Connect geom_stripe and geom_nop modules to the build.
- Connect STRIPE and NOP classes to the LINT build.
- Disconnect gconcat(8) from the build.
Supported by: Wheel - Open Technologies - http://www.wheel.pl
is intend to be fast. Just like CONCAT class it provides manual and
auto configuration methods.
Supported by: Wheel - Open Technologies - http://www.wheel.pl
it is very useful for tests. One is able to destroy its provider
forcibly if wants to test how other class handle such events.
One is also able to specify failure probability to check how other
classes handle I/O errors.
Supported by: Wheel - Open Technologies - http://www.wheel.pl
unless it's in the closed or listening state (remote address
== INADDR_ANY).
If a TCP inpcb is in any other state, it's impossible to steal
its local port or use it for port theft. And if there are
both closed/listening and connected TCP inpcbs on the same
localIP:port couple, the call to in_pcblookup_local() will
find the former due to the design of that function.
No objections raised in: -net, -arch
MFC after: 1 month
to <sys/gmon.h>. Cleaned them up a little by not attempting to ifdef
for incomplete and out of date support for GUPROF in userland, as in
the sparc64 version.
of kmupetext(). The declaration is misplaced in <machine/profile.h>
since it is not MD and not related to the lowest level of profiling.
It will be moved, but getting it via <sys/gmon.h> already works.
algorithm, supplied by wpaul himself. The lame one has an origin
that's been called into question, so rather than argue about that (one
could make an excellent fair use argument), replace it with better
code since that's what FreeBSD is about.
Submitted by: wpaul[1], Klaus Klein
[1] Bill called this a silly bikeshed. Maybe his is not incorrect.
and cannot handle it going away, add an explicit reference to the kobj
class inside each linker class. Without this, a class with no modules
loaded will sit with an idle refcount of 0. Loading and unloading
a module with it causes a 0->1->0 transition which frees the ops table
and causes subsequent loads using that class to explode. Normally, the
"kernel" module will remain forever loaded and prevent this happening, but
if you have more than one linker class active, only one owns the "kernel".
This finishes making modules work for kldload(8) on amd64.
(nobits) tables to simplify some code. Try and shorten some of the very
wide lines. Somewhere along the way, I think I fixed the memory
corruption that caused panics after going multiuser.
to avoid lock order problems when manipulating the sockets associated
with the fifo.
Minor optimization of a couple of calls to fifo_cleanup() from
fifo_open().
reimplementations of enodev() (for the smbread() and smbwrite()
functions), as well as fixing various errno values to conform to
errno(3).
Bruce also points out that a number of the pointer == NULL tests
are probably nonsense because the respective checks are already
done at upper layers.
(Mostly) submitted by: bde
remove the empty line between the fdc and sio devices. The empty
line suggests that the comment applies to fdc only while it applies
to all following devices and options.
Typo spotted by: ru@
controllers and allows the controller to prefetch 1-2k on certain
PCI memory reads to the host. The spec says this should only be
used for IA32 based systems.
Informed of feature by: John Cagle <first.last@hp.com>
gets the relocation base passed in relocbase, we cannot declare a
local variable with the same name. Assume the argument holds the
same value as the local variable did...
repocopied. Soon there will be additional bus attachments and
specialization for isa, acpi and pccard (and maybe pc98's cbus).
This was approved by nate, joerg and myself. bde dissented on the new
location, but appeared to be OK after some discussion.
different context support for 32 vs 64 bit processes. This simply omits
the save/restore of the segment selector registers for non 32 bit
processes. This avoids the rdmsr/rwmsr juggling when restoring %gs
clobbers the kernel msr that holds the gsbase.
However, I suspect it might be better to conditionally do this at
user<->kernel transition where we wouldn't need to do the juggling in the
first place. Or have per-thread extended context save/restore hooks.
hal_raise_irql(void) doesn't take an argument, but it is called with one.
eg: irql = FASTCALL1(hal_raise_irql, DISPATCH_LEVEL);
This is hidden by the macros on i386, but becomes a compile error on amd64
since the arguments are actually checked.
to help the AMD cpus (which have a hardware tlb flush filter). I held
off to see what the 64 bit Intel cpus did, but it doesn't seem to help
much there either. Oh well, store it in the Attic.
properly using copyin/copyout for more than 5 years? This one did. :-)
Properly encapsulate all user<->kernel data transfers using copy{in,out}.
MFC after: 1 month
NULL name in device_add_child(), explicitly name all of our known
child drivers in order to give them a chance to attach to us.
Otherwise, only the first one present would be probed and attached.
Reviewed by: nsouch
MFC after: 1 month
yet, but building kld's is OK now and they can be loaded by kldload(2).
(but the machine will likely crash soon afterwards, a "minor" problem :-)
Brought to you by: my injured knee (from moving)
elf_reloc() backends for two reasons. First, to support the possibility
of there being two elf linkers in the kernel (eg: amd64), and second, to
pass the relocbase explicitly (for relocating .o format kld files).
fragment to zero the valid parts of a VM_IO buffer.
RE would like this to be part of 4.10-RC3 so this will be MFC-ed immediately.
Reviewed by: alc, tegge
is "void *" (it isn't) or that the default promotion of pid_t is int.
Instead, assume that casting "struct foo *" to "void *" and printing the
result with %p is useful, and that all pid_t's are representable as longs.
Fixed some minor style bugs (mainly spelling errors in comments).
It only supports sa1110 (on simics) right now, but xscale support should come
soon.
Some of the initial work has been provided by :
Stephane Potvin <sepotvin at videotron.ca>
Most of this comes from NetBSD.
Wind River. In the IPv4 output path, one of the tests in ip_output()
checks how many slots are actually available in the interface output
queue before attempting to send a packet. If, for example, we need
to transmit a packet of 32K bytes over an interface with an MTU of
1500, we know it's going to take about 21 fragments to do it. If
there's less than 21 slots left in the output queue, there's no point
in transmitting anything at all: IP does not do retransmission, so
sending only some of the fragments would just be a waste of bandwidth.
(In an extreme case, if you're sending a heavy stream of fragmented
packets, you might find yourself sending nothing by the first fragment
of all your packets.) So if ip_output() notices there's not enough
room in the output queue to send the frame, it just dumps the packet
and returns ENOBUFS to the app.
It turns out ip6_output() lacks this code. Consequently, this caused
the netperf UDPIPV6_STREAM test to produce very poor results with large
write sizes. This commit adds code to check the remaining space in the
output queue and junk fragmented packets if they're too big to be
sent, just like with IPv4. (I can't imagine anyone's running an NFS
server using UDP over IPv6, but if they are, this will likely make them
a lot happier. :)
fills its field (6 characters). In that case the OEMID is not
null-terminated, and the sprintf that was used would copy up to the
next null byte, which could be pretty far away.
registers, so add a register offset array to the softc. We key off the
device ID to determine which set of register offsets. Currently the 8385
host bridge used on amd64 is the only bridge to use the AGP3_VIA_*
register offsets and all other bridges use the AGP_VIA_* offsets. It is
currently unclear if the AGP3_VIA_* offsets are for VIA bridges that
implement AGP 3.0 bridges or just for amd64 bridges.
Submitted by: Kenneth Culver culverk at sweetdreamsracing dot biz
removes a specific thread from a sleep queue. sleepq_resume_thread()
resumes scheduling of a thread that has been previously removed from a
sleep queue.
- sleepq_catch_signals() just removes a thread from the queue it was just
added to when a pending signal is found.
- sleepq_signal() and sleepq_broadcast() remove threads from a queue,
drop the queue lock, and then resume all the previously removed threads.
This doesn't completely fix the sched_lock <-> sleepq chain LOR, but it
makes it a little better as we no longer call setrunnble() with a sleep
queue lock held meaning if setrunnable() tries to wakeup the swapper we
don't try to lock two sleep queue chains at the same time.
proper locking to be checked at runtime.
Remove sb_lock() and sb_unlock() calls from sb_reset_dsp() because the
latter is called from sb_setup() with the lock already held. Add a
call to sb_lockassert().
Surround the call to sb_reset_dsp() in sb16_attach() with sb_lock()
and sb_unlock() calls.
Tested by: Bartek Marcinkiewicz <junior AT p233.if.pwr.wroc.pl>
an option. Note that this option doesn't follow the normal USB_ or
Uxxx_ convention. That's because it is this way in the upstream
provider and I didn't want to change that.
Some of the conditions that caused vm_page_select_cache() to deactivate a
page were wrong. For example, deactivating an unmanaged or wired page is a
nop. Thus, if vm_page_select_cache() had ever encountered an unmanaged or
wired page, it would have looped forever. Now, we assert that the page is
neither unmanaged nor wired.
Allow 500us between pauses in ahd_pause_and_flushwork().
The maximum we will wait is now 500ms.
In the same routine, remove any attempt to clear ENSELO.
Let the firmware do it once the current selection has
completed. This avoids some race conditions having to
do with non-packetized completions and the auto-clearing
of ENSELO on packetized completions.
Also avoid attempts to clear critical sections when
interrups are pending. We are going to loop again
anyway, so clearing critical sections is a waste of
time. It also may not be possible to clear a critical
section if the source of the interrupt was a SEQINT.
aic79xx_pci.c:
Use the Generic 9005 mask when looking for generic 7901B
parts. This allows the driver to attach to 7901B parts
on motherboards using a non-Adaptec subvendor ID.
aic79xx_inline.h:
Test for the SCBRAM_RD_BUG against the bugs
field, not the flags field in the softc.
aic79xx.c:
Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
aic79xx.c:
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case
aic79xx.c:
Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command. This
safety measure is added in response to a timeout recovery
failure on H2B where it appears that incoming reselection
status was lost during a drive pull test. In that case,
the recovery handler continued to wait for the command
that was active on the bus indefinetly. While the root
cause of the above issue is still being determined seems
a prudent safeguard.
aic79xx_pci.c:
Add a specific probe entry for the Dell OEM 39320(B).
aic79xx.c:
aic79xx.h:
aic79xx.reg:
aic79xx.seq:
Modify the aic79xx firmware to never cross a cacheline or
ADB boundary when DMA'ing completion entries to the host.
In PCI mode, at least in 32/33 configurations, the SCB
DMA engine may lose its place in the data-stream should
the target force a retry on something other than an
8byte aligned boundary. In PCI-X mode, we do this to
avoid split transactions since many chipsets seem to be
unable to format proper split completions to continue
the data transfer.
The above change allows us to drop our completion entries
from 8 bytes to 4. We were using 8 byte entries to ensure
that PCI retries could only occur on an 8byte aligned
boundary. Now that the sequencer guarantees this by splitting
up completions, we can safely drop the size to 4 bytes (2
byte tag, one byte SG_RESID, one byte pad).
Both the split-completion and PCI retry problems only show
up under high tag load when interrupt coalescing is being
especially effective. The switch from a 2byte completion
entry to an 8 byte entry to solve the PCI problem increased
the chance of incurring a split in PCI-X mode when multiple
transactions were completed at once. Dropping the completion
size to 4 bytes also means that we can complete more commands
in a single DMA (128byte FIFO -> 32 commands instead of 16).
aic79xx.c:
Modify the SCSIINT handler to defer clearing
sequencer critical sections to the individual
interrupt handlers. This allows us to
immediately disable any outgoing selections in
the case of an unexpected busfree so we don't
inadvertantly clear ENSELO *after* a new selection
has started. Doing so may cause the sequencer
to miss a successful selection.
In ahd_update_pending_scbs(), only clear ENSELO if
the bus is currently busy and a selection is not
already in progress or the sequencer has yet to
handle a pending selection. While we want to ensure
that the selection for the SCB at the head of the
selection queue is restarted so that any change in
negotiation request can take effect, we can't clobber
pending selection state without confusing the sequencer
into missing a selection.
sequencer interrupt codes. These codes are only
relevant to the code that was last being executed
and that context is cleared when we reset the
program counter. This addresses a race condition
between a sequencer interrupt and any SCSI event
that causes us to restart the sequencer.
o When running the untagged-Q, we must start the
timer for any transaction we queue.
o Give the firmware half a millisecond between
pauses to flush work out. This should give us
around half a second of total delay before flagging
an issue with pausing and flushing controller work.
Only attempt to clear critical sections if there
are no pending interrupts in the pause and flush
loop. If the sequencer has issued an INTSTAT, we
may not be able to step out of the critical section.
o Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
o In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case.
o Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command.
are used.
- Reduce duplication of a couple of macros removing the duplicates from
ich.h.
- Remove unused macros from icu.h as well as locore protection as this
header is no longer included in assembly sources.
- Require the APIC enumerators to explicitly enable mixed mode by calling
ioapic_enable_mixed_mode(). Calling this function tells the apic driver
that the PC-AT 8259A PICs are present and routable through the first I/O
APIC via an ExtINT pin. The mptable enumerator always calls this
function for now. The MADT enumerator only enables mixed mode if the
PC-AT compatability flag is set in the MADT header.
- Allow mixed mode to be enabled or disabled via a 'hw.apic.mixed_mode'
tunable. By default this tunable is set to 1 (true). The kernel option
NO_MIXED_MODE changes the default to 0 to preserve existing behavior, but
adding 'hw.apic.mixed_mode=0' to loader.conf achieves the same effect.
- Only use mixed mode to route IRQ 0 if it is both enabled by the APIC
enumerator and activated by the loader tunable. Note that both
conditions must be true, so if the APIC enumerator does not enable mixed
mode, then you can't set the tunable to try to override the enumerator.
to map. If the checksum fails, the table is unmapped and a NULL pointer
returned.
- For ACPI version >= 2.0, check the extended checksum of the RSDP.
AcpiOsGetRootPointer() already checks the version 1.0 checksum.
- Remap the full MADT table at the end of madt_probe() so that we verify
its checksum before saying it is really there.
Requested by: njl
the swizzle method for routing PCI interrupts across the bridge. This
fixes problems with motherboards (typically laptops) whose BIOS doesn't
provide a PRT for the AGP bridge even though there is a device entry for
the bridge in the ACPI namespace.
Tested by: Kenneth Culver culverk at sweetdreamsracing dot biz
it back to userspace, so it does not break bind(2) on raw sockets in jails.
Currently some processes, like traceroute(8) construct a routing request
to determine its source address based on the destination. This sockaddr
data is fed directly to bind(2). When bind calls ifa_ifwithaddr(9) to
make sure the address exists on the interface, the comparison will
fail causing bind(2) to return EADDRNOTAVAIL if the data wasnt zero'ed
before initialization.
Approved by: bmilekic (mentor)
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.
Approved by: tmm, no objections on freebsd-sparc64
It's not quite correct from a posix Point Of view, but it is a lot better
than what was there before. This will be revisited later
when we decide what form our priority extensions will take. Posix doesn't
specify how a system scope thread can change its priority so you need to
add non-standard extensions to be able to do it..
For now make this slightly non standard to allow it to be done.
Submitted by: Dan Eischen originally, changed by myself.
there's not dependencies on pccard symboles, such a dependency is not
necessary. This means that drivers that have multiple attachments can
not drag bogus devices into the kernel at load time.
We can't (yet) do this with pci and isa. Drivers written for them
actually do seem to have symbols that depend on these busses'
implementation code.
ndis not touched until other things can be tested.
the kernel. We can guarantee this by resetting the FP status register.
This masks all FP traps. The reason we did get FP traps was that we
didn't reset the FP status register in all cases.
Make sure to reset the FP status register in syscall(). This is one of
the places where it was forgotten.
While on the subject, reset the FP status register only when we trapped
from user space.
Previously, mlockall(2) usage would leak MAP_FUTUREWIRE of the process's
vmspace::vm_map and subsequent processes would wire all of their memory.
Coupled with a wired-page leak in vm_fault_unwire(), this would run the
system out of free pages and cause programs to randomly SIGBUS when
faulting in new pages.
(Note that this is not the fix for the latter part; pages are still
leaked when a wired area is unmapped in some cases.)
Reviewed by: alc
PR kern/62930
of IP options.
net.inet.ip.process_options=0 Ignore IP options and pass packets unmodified.
net.inet.ip.process_options=1 Process all IP options (default).
net.inet.ip.process_options=2 Reject all packets with IP options with ICMP
filter prohibited message.
This sysctl affects packets destined for the local host as well as those
only transiting through the host (routing).
IP options do not have any legitimate purpose anymore and are only used
to circumvent firewalls or to exploit certain behaviours or bugs in TCP/IP
stacks.
Reviewed by: sam (mentor)
devices it cannot attach to. This gets rid of extraneous but harmless
device_probe_and_attach() errors. While I'm here, make the device
description more useful. The !acpi case for cpu is handled by legacy0.
and Rx frames up to 8191 octets, so it is perfectly capable of supporting
vlan(4)-style VLAN natively.
Thus, make it support VLAN `oversize' frames.
Reviewed by: tmm
that the OHCI driver uses. Broken OHCI devices (like the controller
in my laptop, apparently) like to set this bit at times. Research
through google shows that this problem has shown up on other systems
as well.
As the scheduling overrun handler doesn't actually do anything, and
the only effect is console spamming, disabling the interrupt seems
to be the right thing to do. (And it is also what linux 2.6 does.)
allocation and deallocation. This flag's principal use is shortly after
allocation. For such cases, clearing the flag is pointless. The only
unusual use of PG_ZERO is in vfs_bio_clrbuf(). However, allocbuf() never
requests a prezeroed page. So, vfs_bio_clrbuf() never sees a prezeroed
page.
Reviewed by: tegge@
individual asm versions. The global lock is shared between the BIOS and
OS and thus cannot use our mutexes. It is defined in section 5.2.9.1 of
the ACPI specification.
Reviewed by: marcel, bde, jhb
o The ieee80211_media_status() function updates the ifi_link_state field
and calls rt_ifmsg() to notify listeners on the routing socket.
Approved by: sam
2. Note that ct device uses ctau name as driver name (due to name conflict
with ct driver) and also mark it as a driver inside the CVS tree.
MFC after: 10 days
segment, remove the groping around in the Option ROM segments, remove the
bogus tests for bcopy vs. copyout. There really is no reason for a
management app to know these things other than to create l33t info tables
for the user.
a significant functional change, but it further cleans up the code and
brings it closer to being portable. Thanks to Don Bowman for helping to
test this.
and type for printing info about the device that didn't probe from child, not
parent.
This fixes a panic on systems where not yet supported devices hang off of the
nexus, e.g. on E450.
Reported by: joerg
host-PCI bridge device and find a valid $PIR.
- Make pci_pir_parse() private to pci_pir.c and have pir0's attach routine
call it instead of having legacy_pcib_attach() call it.
- Implement suspend/resume support for the $PIR by giving pir0 a resume
method that calls the BIOS to reroute each link that was already routed
before the machine was suspended.
- Dump the state of the routed flag in the links display code.
- If a link's IRQ is set by a tunable, then force that link to be re-routed
the first time it is used.
- Move the 'Found $PIR' message under bootverbose as the pir0 description
line lists the number of entries already. The pir0 line also only shows
up if we are actually using the $PIR which is a bonus.
- Use BUS_CONFIG_INTR() to ensure that any IRQs used by a PCI link are
set to level/low trigger/polarity.
active low polarity when using the PIC interrupt model. This should fix
broken SCI interrupts on machines when not using the APIC where the BIOS
doesn't program the ELCR to level trigger for the ACPI SCI.
Requested by: njl
polarity for a specified IRQ. The intr_config_intr() function wraps
this pic method hiding the IRQ to interrupt source lookup.
- Add a config_intr() method to the atpic(4) driver that reconfigures
the interrupt using the ELCR if possible and returns an error otherwise.
- Add a config_intr() method to the apic(4) driver that just logs any
requests that would change the existing programming under bootverbose.
Currently, the only changes the apic(4) driver receives are due to bugs
in the acpi(4) driver and its handling of link devices, hence the reason
for such requests currently being ignored.
- Have the nexus(4) driver on i386 implement the bus_config_intr() function
by calling intr_config_intr().
and intr_polarity enums for passing around interrupt trigger modes and
polarity rather than using the magic numbers 0 for level/low and 1 for
edge/high.
- Convert the mptable parsing code to use the new ELCR wrapper code rather
than reading the ELCR directly. Also, use the ELCR settings to control
both the trigger and polarity of EISA IRQs instead of just the trigger
mode.
- Rework the MADT's handling of the ACPI SCI again:
- If no override entry for the SCI exists at all, use level/low trigger
instead of the default edge/high used for ISA IRQs.
- For the ACPI SCI, use level/low values for conforming trigger and
polarity rather than the edge/high values we use for all other ISA
IRQs.
- Rework the tunables available to override the MADT. The
hw.acpi.force_sci_lo tunable is no longer supported. Instead, there
are now two tunables that can independently override the trigger mode
and/or polarity of the SCI. The hw.acpi.sci.trigger tunable can be
set to either "edge" or "level", and the hw.acpi.sci.polarity tunable
can be set to either "high" or "low". To simulate hw.acpi.force_sci_lo,
set hw.acpi.sci.trigger to "level" and hw.acpi.sci.polarity to "low".
If you are having problems with ACPI either causing an interrupt storm
or not working at all (e.g., the power button doesn't turn invoke a
shutdown -p now), you can try tweaking these two tunables to find the
combination that works.
IRQ is edge triggered or level triggered. For ISA interrupts, we assume
that edge triggered interrupts are always active high and that level
triggered interrupts are always active low.
- Don't disable an edge triggered interrupt in the PIC. This avoids
outb instructions to the actual PIC for traditional ISA IRQs such as
IRQ 1, 6, 14, and 15. (Fast interrupts such as IRQs 0 and 8 don't mask
their source, so this doesn't change anything for them.)
- For MCA systems we assume that all interrupts are level triggered and
thus need masking. Otherwise, we probe the ELCR. If it exists we trust
what it tells us regarding which interrupts are level triggered. If it
does not exist, we assume that IRQs 0, 1, 2, and 8 are edge triggered
and that all other IRQs are level triggered and need masking.
- Instruct the ELCR mini-driver to restore its saved state during resume.
register controlled the trigger mode and polarity of EISA interrupts.
However, it appears that most (all?) PCI systems use the ELCR to manage
the trigger mode and polarity of ISA interrupts as well since ISA IRQs used
to route PCI interrupts need to be level triggered with active low
polarity. We check to see if the ELCR exists by sanity checking the value
we get back ensuring that IRQS 0 (8254), 1 (atkbd), 2 (the link from the
slave PIC), and 8 (RTC) are all clear indicating edge trigger and active
high polarity.
This mini-driver will be used by the atpic driver to manage the trigger and
polarity of ISA IRQs. Also, the mptable parsing code will use this mini
driver rather than examining the ELCR directly.
not as a pending interrupt status, but as a matter of status quo.
Consequently, when there's no data to be transmitted the condition
is not cleared and uart_intr() is stuck in an infinite loop trying
to clear the UART_IPEND_TXIDLE status.
The z8530_bus_ipend() function is changed to return idle only once
after having sent any data.
The root cause for this problem is that we cannot use the interrupt
status bits of the SCC itself. The register that holds the interrupt
status can only be accessed by channel A and holds the status for
both channels. Using the interrupt status register would complicate
the driver because we need to synchronize access to the SCC between
the channels.
Elementary testing: marius
labeling new mbufs created from sockets/inpcbs in IPv4. This helps avoid
the need for socket layer locking in the lower level network paths
where inpcb locks are already frequently held where needed. In
particular:
- Use the inpcb for label instead of socket in raw_append().
- Use the inpcb for label instead of socket in tcp_output().
- Use the inpcb for label instead of socket in tcp_respond().
- Use the inpcb for label instead of socket in tcp_twrespond().
- Use the inpcb for label instead of socket in syncache_respond().
While here, modify tcp_respond() to avoid assigning NULL to a stack
variable and centralize assertions about the inpcb when inp is
assigned.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, McAfee Research
lookup for the label tag fails, return NULL rather than something close
to NULL. This scenario occurs if mbuf header labeling is optional and
a policy requiring labeling is loaded, resulting in some mbufs having
labels and others not. Previously, 0x14 would be returned because the
NULL from m_tag_find() was not treated specially.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, McAfee Research
returns okay when HW probe fails. This happens when comconsole flag is
set but VGA console is used instead.
Back out requested by: bde (He will be looking at other solutions from scratch)
test the label pointer for NULL before testing the label slot for
permitted values. When loading mac_test dynamically with conditional
mbuf labels, the label pointer may be NULL if the mbuf was
instantiated while labels were not required on mbufs by any policy.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, McAfee Research
synchronization protecting against dynamic load and unload of MAC
policies, and instead simply blocks load and unload. In a static
configuration, this allows you to avoid the synchronization costs
associated with introducing dynamicism.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, McAfee Research
interrupt source.
- Only do an outb() to the PIC to clear a bit in imen if the bit is set.
- Add a NUM_ISA_IRQS macro to replace uglier
'sizeof(array) / sizeof(member)' expressions along with a CTASSERT() to
ensure that the macro is correct.
than using legacy_pcib_attach(). The MP Table drivers don't use the $PIR,
and the legacy_pcib_attach() function probes and parses the $PIR in
addition to adding the pci bus child device.
o New function ip_findroute() to reduce code duplication for the
route lookup cases. (luigi)
o Store ip_len in host byte order on the stack instead of using
it via indirection from the mbuf. This allows to defer the host
byte conversion to a later point and makes a quicker fallback to
normal ip_input() processing. (luigi)
o Check if route is dampned with RTF_REJECT flag and drop packet
already here when ARP is unable to resolve destination address.
An ICMP unreachable is sent to inform the sender.
o Check if interface output queue is full and drop packet already
here. No ICMP notification is sent because signalling source quench
is depreciated.
o Check if media_state is down (used for ethernet type interfaces)
and drop the packet already here. An ICMP unreachable is sent to
inform the sender.
o Do not account sent packets to the interface address counters. They
are only for packets with that 'ia' as source address.
o Update and clarify some comments.
Submitted by: luigi (most of it)
o Extend the if_data structure with an ifi_link_state field and
provide the corresponding defines for the valid states.
o The mii_linkchg() callback updates the ifi_link_state field
and calls rt_ifmsg() to notify listeners on the routing socket
in addition to the kqueue KNOTE.
o If vlans are configured on a physical interface notify and update
all vlan pseudo devices as well with the vlan_link_state() callback.
No objections by: sam, wpaul, ru, bms
Brucification by: bde
the falling edge of a media state change.
This is in preparation for media state change notification to the
routing socket.
No objections by: sam, wpaul, ru, bms
Brucification by: bde
o Fix and improve comments and references,
o Add PFIL_HOOKS, UFS_ACL and UFS_DIRHASH,
o Switch from SCHED_4BSD to SCHED_ULE,
o Remove SCSI_DELAY (there's no SCSI support),
- change pf_get_pool() argument rule_number type from u_int32_t
to u_int8_t, fixes corruption of address pools with large
rulesets (mcbride@)
- prevent endless loops with route-to (dhartmei@)
- limit option length to 2 octets max (frantzen@)
Obtained from: OpenBSD
Approved by: mlaier(mentor), bms(mentor)
uncommitted):
Rename ip_claim_next_hop() to m_claim_next_hop(), give it an extra arg
(the type of tag to claim) and push it out of ip_var.h into mbuf.h
alongside all of the other macros that work ok mbuf's and tag's.
