Commit Graph

11 Commits

Author SHA1 Message Date
David Greenman
397f9dfe26 Work around a bug in the 82557 NIC where the receiver will lock up
if it is in 10Mbps mode and gets certain types of garbage prior to
the packet header. The work-around involves reprogramming the
multicast filter if nothing is received in some number of seconds
(currently set at 15). As a side effect, implemented complete support
for multicasting rather than the previous 'receive all multicasts'
hack, since we now have the ability to program the filter table.
Fixed a serious bug which crept in with the timeout() changes;
the cookie was only saved on the first timeout() call in fxp_init()
and wasn't updated in the most common place in fxp_stats_update()
when the timeout was rescheduled. This bug would have resulted in
an eventual panic if fxp_stop() was called (which happens when any
interface flags are changed, for example).
Fixed a bug in Alpha support that would have caused the TxCB
descriptor chain to span a page boundry, causing serious problems
if the pages didn't happen to be contiguous.
Removed some gratuitous bit masking that was left over from an
older implementation.
Fixed a bug where too much was copied from the configuration
template, spilling over into memory that followed it.
Fixed handling of if_timer...it was cleared too early in some cases.
1997-09-29 11:27:43 +00:00
David Greenman
ba8c6fd534 Changes to support NetBSD and the new ifmedia extensions.
Submitted by:	Jason Thorpe <thorpej@netbsd.org>
1997-09-05 10:23:58 +00:00
David Greenman
854d14213e Added support for the Intel 82555 PHY chip which is being used on newer
Pro/100B cards. Full duplex should work now, although it hasn't been
tested.
1997-06-13 22:34:52 +00:00
David Greenman
6ebc315326 Added support for newer cards that have the DP83840A PHY chip.
Fixed a bug in fxp_mdi_write - a hex number was missing a preceding 0x
and this was causing the routine to not wait for a PHY write to complete.
Added support for link0, link1, and link2 flags to toggle auto-
negotiation, 10/100, and half/full duplex:

link0	disable auto-negotiation

	When set, these flags then have meaning:

	-link1	10Mbps
	link1	100Mbps
	-link2	half duplex
	link2	full duplex

...needs a manual page.
1997-03-21 08:00:13 +00:00
David Greenman
dccee1a193 Fixed two deficiencies in the driver that have existed since it was
written:

1) Full duplex mode is now supported (and works!)
2) The 10Mbps-only PCI Pro/10 should now work (untested, however)

Thanks to Justin Gibbs for providing a PCI bus analyzer trace while the
Intel Windows driver was configuring the board...this made it possible
to figure out the mystery bit that I wasn't setting in the PHY for full
duplex to work.
1997-03-17 11:08:16 +00:00
Peter Wemm
6875d25465 Back out part 1 of the MCFH that changed $Id$ to $FreeBSD$. We are not
ready for it yet.
1997-02-22 09:48:43 +00:00
David Greenman
33d14d8671 Do "selective" reset rather than full reset...the manual specifically
says not to do the full reset because it can lock up the PCI bus if the
chip is active. Added various PORT command definitions to facilitate
this.
1997-02-04 10:53:12 +00:00
Jordan K. Hubbard
1130b656e5 Make the long-awaited change from $Id$ to $FreeBSD$
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.

Boy, I'm glad we're not using sup anymore.  This update would have been
insane otherwise.
1997-01-14 07:20:47 +00:00
David Greenman
58b248e254 Removed sections 3 and 4 from my copyright. 1996-04-08 01:31:42 +00:00
David Greenman
23a0ed7c08 Increased the number of Tx segments from 13 to 29 to reduce the need to
recopy to near zero. Wrote the necessary code to recopy the mbuf chain
into another buffer if there are too many mbufs in the chain.
1995-12-05 11:49:55 +00:00
David Greenman
a17c678ed2 Device driver for Intel Pro/100 PCI Fast Ethernet controller. 1995-11-28 23:55:26 +00:00