these look to be cut and pasted from other drivers since this driver was
committed to FreeBSD 7-current and MFC'd to FreeBSD 6. The ones for FreeBSD 4
and 5 likely never were working...
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
but taken from hardware.
- Mechanically convert to if_inc_counter() the rest of counters.
- While here fix 3 instances of the same bug, when error counter was ++
in one place and then assigned in other place, losing the increment.
Achieve that storing soft errors counters in softc.
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
freeing them instead of after.
- Check the bus address of a static DMA buffer to decide if the associated
map should be unloaded.
- Don't try to destroy bus dma maps for static DMA buffers.
Reviewed by: davidcs
out 32 is not enough to support a full sized TSO packet.
While I'm here fix a long standing bug introduced in r169632 in
bce(4) where it didn't include L2 header length of TSO packet in
the maximum DMA segment size calculation.
In collaboration with: rmacklem
MFC after: 2 weeks
r235816 triggered kernel panic or hang after warm boot.
Don't blindly restore BCE_EMAC_MODE media configuration in
bce_reset(). If driver is about to shutdown it will invoke
bce_reset() which in turn results in restoring BCE_EMAC_MODE
media configuration. This operation seems to confuse controller
firmware.
Reported by: Paul Herman (herman <> cleverbridge dot com)
Tested by: sbruno, Paul Herman (herman <> cleverbridge dot com)
state. Previously it used to check if controller has sent a
PAUSE frame to the remote peer.
Reported by: David Imhoff via Brad Smith <brad@OpenBSD.org>
Submitted by: davidch (initial version)
Reviewed by: davidch, David Imhoff <dimhoff_devel@xs4all.nl>
Actually, this may be further optimized for controller variants
supporting one-shot MSIs but I'm lacking the necessary hardware for
testing.
- Add some missing synchronization of the statistics and status DMA
maps.
MFC after: 1 week
altered or actually needed there any longer.
- Honor errors passed to the DMA mapping callbacks.
- In bce_get_rx_buf(), do not reserve stack space for more DMA segments
than actually necessary.
- In bce_get_pg_buf(), take advantage of bus_dmamap_load_mbuf_sg(9).
- In bce_rx_intr(), remove a pointless check for an empty mbuf pointer
which can only happen in case of a severe programming error. Moreover,
recovering from that situation would require way more actions with header
splitting enabled (which it is by default).
- Fix VLAN tagging in the RX path; do not attach the VLAN tag twice if the
firmware has been told to keep it. [1]
Obtained from: OpenBSD [1]
MFC after: 1 week
patching at runtime actually const.
- Remove pointless softc members by employing the corresponding constants
directly.
- Remove pointless returns.
- Remove unnecessary inclusion of opt_device_polling.h.
- Replace an outdated and now bogus comment in bce_tick() with the
appropriate one.
MFC after: 1 week
- Use NULL instead of 0 for pointers.
- Remove redundant bzero(9)'ing of the softc.
- Remove redundant/unused softc members.
- Don't allocate MSI/MSI-X as RF_SHAREABLE.
- Re-use bus accessor macros instead of duplicating them.
- In bce_miibus_{read,write}_reg(), remove superfluous limiting of the PHY
address (missed in r213893).
MFC after: 1 week
configured down. Formerly, IPMI communication was lost whenever the
interface was not up. The reason was that the BCE_EMAC_MODE
register was not configured with the correct media settings. There
are two parts to the fix.
First, resetting the chip in bce_reset() causes the BCE_EMAC_MODE
register to be initialized to a default value that does not
necessarily correspond to the actual media settings. The fix
implemented here is a bit of a hack. Ideally, at the end of
bce_reset() we would poll the PHY to determine the negotiated media,
and then we would set the BCE_EMAC_MODE register accordingly. That
is difficult, since the PHY is abstracted behind the MII layer and is
not supposed to be queried directly from the MAC driver. Instead,
we read the BCE_EMAC_MODE register at the beginning of bce_reset()
and then restore its media bits to their original values before
returning. If IPMI is up and running, then the link is already
established and the BCE_EMAC_MODE register is already set appropriately
when bce_reset() is called. If IPMI is not running, no harm is
done by preserving the BCE_EMAC_MODE settings. The driver will set
the register properly once the interface is configured up and link
is established.
Second, bce_miibus_statchg() is sometimes called when the link is
down. In that case, the reported media settings are invalid.
Formerly, the driver used them anyway to setup the BCE_EMAC_MODE
register. We now avoid changing any MAC registers unless link is
active and the reported media settings are valid.
Submitted by: jdp
Tested by: jdp
MFC after: 5 days
controller to perform MDIO type accesses to a remote transceiver
using message pages defined through MRBE(multirate backplane
ethernet). It's used in blade systems(e.g Dell Blade m610) which
are connected to pass-through blades rather than traditional
switches.
This change directly manipulates firmware's mailboxes to control
remote PHY such that it does not use mii(4). Alternatively, as
David said, it could be implemented in brgphy(4) by creating a fake
PHY and let brgphy(4) do necessary mii accesses and bce(4) can
implement mailbox accesses based on the type of brgphy(4)'s mii
accesses. Personally, I think it would make brgphy(4) hard to
maintain since it would have to access many bce(4) registers in
brgphy(4). Given that there are users who are suffering from lack
of remote PHY support, it would be better to get working system
rather than waiting for complete/perfect implementation.
Tested by: Jan Winter ( jan.winter <> kantarmedia dot de )
Reviewed by: davidch (initial version)
MFC after: 2 weeks
r228476 fixed superfluous link UP/DOWN messages but broke IPMI
access during boot. It's not clear why r228476 breaks IPMI and
should be revisited.
Reported by: Paul Guyot <paulguyot <> ieee dot org >
MFC after: 1 week
messages.
o Add check for actually resolved speed in miibus_statchg callback
instead of blindly reprogramming BCE_EMAC_MODE register. The
callback may be called multiple times(e.g. link UP, link
transition, auto-negotiate complete etc) while auto-negotiation
is in progress. All unresolved link state changes are ignored
now and setting BCE_EMAC_MODE after link establishment is done
once.
o bce(4) is careful enough not to drive MII_TICK if driver got a
valid link. To detect lost link, bce(4) relied on link state
change interrupt and if driver see the interrupt, it forced to
drive MII_TICK by calling bce_tick() in interrupt handler.
Because bce(4) generates multiple link state change interrupts
while auto-negotiation is in progress, bce_tick() would be
called multiple times and this resulted in generating multiple
link UP/DOWN messages.
With this change, bce_tick() is not called in interrupt handler
anymore such that miibus_statchg callback handles link state
changes with consistent manner.
Reviewed by: davidch
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
remove explicit checks for BCM5716.
The BCM5709 and BCM5716 chips are virtually indistinguishable by
software except for the PCI device ID. The two chips differ in
that BCM5709 supports TCP/IP and iSCSI offload in Windows while
the BCM5716 doesn't.
While I'm here remove now unused definition of BCE_CHIP_NUM_5716
and BCE_CHIP_ID_5716_C0.
Reported by: sbruno
Reviewed by: davidch
Tested by: davidch
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
