over GMII, make sure to enable GMII. With this change brgphy(4) is
used to handle the dual mode PHY. Since we still don't have a sane
way to pass PHY specific information to mii(4) layer special
handling is needed in brgphy(4) to determine which mode of PHY was
configured in parent interface.
This change make BCM5715S work.
Tested by: olli
Obtained from: OpenBSD
MFC after: 1 week
o Don't enable BGE_FLAG_BER_BUG on both 5722 and 5756, and based
on their PCI IDs rather than their chip IDs.
Reported by: several PC-BSD users via kmoore
Reviewed by: yongari, imp, jhb, davidch
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
hw.bge.forced_collapse. hw.bge.forced_collapse affects all bge(4)
controllers on system which may not desirable behavior of the
sysctl node. Also allow the sysctl node could be modified at any
time.
Reviewed by: bde (initial version)
seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
Tested by: current
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
Reviewed by: davidch
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
Reviewed by: marius
Introduce two spare dma maps for standard buffer and jumbo buffer
respectively. If loading a dma map failed reuse previously loaded
dma map. This should fix unloaded dma map is used in case of dma
map load failure. Also don't blindly unload dma map and defer
dma map sync and unloading operation until we know dma map for new
buffer is successfully loaded. This change saves unnecessary dma
load/unload operation. Previously bge(4) tried to reuse mbuf
with unloaded dma map which is really bad thing in bus_dma(9)
perspective.
While I'm here update if_iqdrops if we can't allocate Rx buffers.
and Rx DMA tag separately. Previously it used a common mbuf DMA tag
for both Tx and Rx path but Rx buffer(standard ring case) should
have a single DMA segment and maximum buffer size of the segment
should be less than or equal to MCLBYTES. This change also make it
possible to add TSO with minor changes.
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
quirk requiring it to be enabled even when using MSI. This makes
the latter work again after r189285.
- Remove a comment which no longer applies since r190194.
- If boot verbose, print asicrev, chiprev and bus type on attach.
- For PCI Express devices:
1) Adjust max read request size to 4Kbytes
2) Turn on FIFO_LONG_BURST in RDMA during bge_blockinit()
Though 1) does not seem to have much to do with the poor TX performance
observed on PCI Express bge(4), 2) does fix the problem. [1]
- Nuke the RX CPU self-diag, which prevents working cards from working
(Linux tg3 does not have this diag neither does OpenBSD's bge(4)).
The increasing of the firmware handshaking timeout to 20000 retries
done as part of the original commit isn't merged as way already have a
way higher BGE_TIMEOUT of 100000.
PR: 119361 [1]
Obtained from: tg3 via DragonflyBSD [1], DragonflyBSD
- Rename BGE_FLAG_EEPROM to BGE_FLAG_EADDR to underline it's absence means
"there's no chip containing an Ethernet address fitted to the BGE chip
so we have to get it from the firmware instead" rather than "there's no
EEPROM, but maybe NVRAM or something else".
- Don't treat BCM5906[M] generally like chips w/o BGE_FLAG_EADDR set, just
in the two cases really necessary. This gets us line with the original
patch for DragonFlyBSD.
- For sparc64 restore the intended behavior of obtaining the Ethernet
address from the firmware in case BGE_FLAG_EADDR is not set, even for
BCM5906[M].
- Fix some style(9) bugs introduced with rev. 1.208 of if_bge.c
Approved by: jhb
Additional testing by: Thomas Nystroem (BCM5906)
all cards/modes.
In addition to the intr forcing added with rev. 1.205 adopt the other
places to use the same logic.
We need to exclude a few chips/revisions (5700, 5788) from using the
enhanced version and fall back to the old way as that is the only
method they support.
Tested by: phk
Suggested by: davidch, Broadcom (thanks a lot for the help!)
MFC after: 16 days
10/100 operation and place the mailbox registers at a different offset.
They also do not have an EEPROM, so the MAC address must be read from
NVRAM instead.
MFC after: 1 month
PR: kern/118975
Submitted by: benjsc, Thomas Nyström thn at saeab dot se
Submitted by: sephe (original patch for DragonflyBSD)
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
- Move some PHY bug detections from brgphy.c to if_bge.c.
- Do not penalize working PHYs.
- Re-arrange bge_flags roughly by their categories.
- Fix minor style(9) nits.
PR: kern/107257
Obtained from: OpenBSD
Tested by: Mike Hibler <mike at flux dot utah dot edu>
- Do not repeatedly read vendor/device IDs while probing.
- Remove redundant bzero(3) for softc. device_get_softc(9) does it for free[1].
Reviewed by: glebius
Suggested by: glebius[1]
- Use the appropriate register writing method when reseting the chip
- Program the descriptor DMA engine correctly.
- More reliably detect certain chips and their features.
Also add some low-level debugging tools to help future work on this driver.
Submitted by: David Christenson (proof of concept changes)
Sponsored by: www.UIA.net
discarded RX packets to input error for BCM5705 or newer chipset as the others.
Unfortunately we cannot do the same for output errors because ifOutDiscards
equivalent register does not exist. While I am here, replace misleading and
wrong BGE_RX_STATS/BGE_TX_STATS with BGE_MAC_STATS. They were reversed but
worked accidently.
to it. Try to co-operate with the IPMI/ASF firmware accessing the PHY.
One we get link we don't mess with the PHY. If we do then over time
the NIC will go off line. It would be nice if we could tell if IPMI
was enabled on the chip but I can't figure out a reliable way to do
that. The scheme I tried worked on a Dell PE850 but not on an HP machine.
So we assume any NIC that has ASF capability needs to deal with it.
The code was inspired by the support in Linux from kernel.org and Broadcom.
Broadcom did give me some info. but it is rather limited and is mostly
just what is in the Linux driver. Thanks to the numerous people that
helped debug the many prior versions and that I didn't break other
bge(4) HW.
Reviewed by: several people
Tested by: even more
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
- Add more device IDs, ASIC revisions and chip IDs.
- Rewrite a bit code that picks the description for device.
- Introduce several macros to shorten quirks for bugs and
features.[*]
- Use some magic values, that OpenBSD has successfully
possessed from Linux (Broadcom supplied) driver.
- Remove disabled code that tried to access VPD.
[*] The macro that matches Jumbo capable NICs is
rewritten to preserve our current behavior. I
need clarify whether our or theirs is correct.
PR: 68351 (and may be others)
Obtained from: OpenBSD, brad@ mostly
