Summary:
This driver supports the following methods to trigger gathering random bits from the hardware:
1. interrupt when the FIFO is full (default) fed into the harvest queue
2. callout (when BCM2835_RNG_USE_CALLOUT is defined) every second if hz is less than 100, otherwise hz / 100, feeding the random bits into the harvest queue
If the kernel is booted with verbose enabled, the contents of the registers will be dumped after the RBG is started during the attach routine.
Author: hackagadget_gmail.com (Stephen J. Kiernan)
Test Plan: Built RPI2 kernel and booted on board. Tested the different methods to feed the harvest queue (callout, interrupt) and the interrupt driven approach seems best. However, keeping the other method for people to be able to experiment with.
Reviewed By: adrian, delphij, markm
Differential Revision: https://reviews.freebsd.org/D6888
TDMA and CESA registers are placed in different ranges of memory. Split
memory resource in DTS to reflect that. This change is needed to support
multiple CESA nodes as otherwise the ranges of different nodes would
overlap.
In consequence, CESA_WRITE and CESA_READ macros have been split depending
on which range of registers is accessed. Offsets for CESA registers have
been modified as the base address has changed.
Submitted by: Michal Stanek <mst@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D6217
Commit was temporary fix due to rman_res_t defined as 32-bit u_long.
After redefining it as 64-bit variable workaround is not needed and
was removed.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D6214
Pressing the PEK (power enable key) will shutdown the board.
Some events are reported to devd via system "PMU" and subsystem
"Battery", "AC" and "USB" such as connected/disconnected.
Some sensors values (power source voltage/current) are reported via
sysctl (dev.axp209_pmu.X.)
It also expose a gpioc node usable in kernel and userland. Only 3 of
the 4 GPIO are exposed (The GPIO3 is different and mostly unused on
boards). Most popular boards uses GPIO1 as a sense pin for OTG power.
Add a dtsi file that adds gpio-controller capability to the device as
upstream doesn't defined it and include it in our custom DTS.
Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6135
PCIe PHY needs different initialization on MT7628/MT7688 SoCs than it does
on MT7620.
However, LEDE (and OpenWRT) dts files have the PCIe node for MT7628/MT7688
as compatible with mt7620-pci.
We already can handle this properly in our driver, so we just need to add
compat strings to fbsd-mt7628an.dtsi and the PCIe driver.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6395
This is an import of the reworked LEDE dts files. Besides other things
they make it easier for us to reuse.
The only diffs left are for the following SoCs:
MT7620A (fbsd-mt7620a.dtsi)
MT7621 (fbsd-mt7621.dtsi)
MT7628 (fbsd-mt7628an.dtsi)
RT3883 (fbsd-rt3883.dtsi)
So we include the fbsd-*.dtsi files at the end of the original LEDE dtsi
files, using '#include "fbsd-xxxx.dtsi"'.
For example, for MT7621, the LEDE dtsi file is mt7621.dtsi. At the end of
it we add:
#include "fbsd-mt7621.dtsi"
Approved by: adrian (mentor)
Obtained from: LEDE project
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6394
The A83T thermal sensor controller has three sensors. Sensor 0 corresponds
to CPU cluster 0, sensor 1 to CPU cluster 1, and sensor 2 to the GPU. This
driver exports the temperature sensor readings via sysctl.
Calibration data is obtained from SRAM found in the Secure ID module.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D6378
- Factor out common part to zynq-7000.dtsi
- Fix problem with Zynq interrupts by using interrupt "triples"
in .dtsi file to differentiate between edge-triggered and
level-triggered interrupts
- cgem driver now recognizes "status" property
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D6095
The introduction of palmbus and previous work allows us to cut the
differences between FreeBSD and OpenWRT DTS files a bit further.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6043
This change is required so that RT3662/RT3883 PCI can function correctly
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6028
This revision suggests dtsi patches to be used with the original OpenWRT
dtsi files so we can re-use what has already been done in OpenWRT for the
Mediatek/Ralink SoCs.
The only thing that is required after importing this revision should be
the following:
1. Import OpenWRT dts/dtsi files into sys/gnu/dts/mips
2. Run the following script in sys/gnu/dts/mips:
for f in `ls [mr]t*.dtsi`; do
printf "\n#include <fbsd-$f>\n" > $f
done
This will apply our dtsi patches to OpenWRT's dtsi files and will allow us
to re-use dts/dtsi files for ~170 Mediatek/Ralink boards.
Currently our drivers are not 100% compatible with OpenWRT's dts files, but
they're compatible enough.
We can add more functionality in the future that would better leverage the
OpenWRT work as well.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5965
a child of it. This is done in conformity with Linux dts files and
as preparation for rework of BCM2836 interrupt controller for INTRNG.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D5807
The following pheripherals are supported: UART, MMC, AHCI, EHCI, PCIe, I2C,
PMIC, GPIO, CPU temperature and clock.
Note: The PCIe driver is pure mash at this moment. It will be reworked
immediately when both D5237 and D2579 enter the current tree.
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
Tested on Spike simulator with 2 and 16 cores (tlb enabled),
so set MAXCPU to 16 at this time.
This uses FDT data to get information about CPUs
(code based on arm64 mp_machdep).
Invalidate entire TLB cache as it is the only way yet.
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202
dts files. It may be removed once it will be fixed upstream.
This is done just to supresses a warning during dtb evaluation as
there is no elm driver in tree at present.
least the audio codec driver currently in review.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5050
o Add kernel configuration for QEMU.
Both SPIKE and QEMU kernel configs are temporary (until
we will be able to obtain DTB from loader).
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
This is the final step required allowing to compile and to run RISC-V
kernel and userland from HEAD.
RISC-V is a completely open ISA that is freely available to academia
and industry.
Thanks to all the people involved! Special thanks to Andrew Turner,
David Chisnall, Ed Maste, Konstantin Belousov, John Baldwin and
Arun Thomas for their help.
Thanks to Robert Watson for organizing this project.
This project sponsored by UK Higher Education Innovation Fund (HEIF5) and
DARPA CTSRD project at the University of Cambridge Computer Laboratory.
FreeBSD/RISC-V project home: https://wiki.freebsd.org/riscv
Reviewed by: andrew, emaste, kib
Relnotes: Yes
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
Differential Revision: https://reviews.freebsd.org/D4982
Invalid (in FreeBSD) definition of PCI controller was
replaced with another one, working in FreeBSD environment.
PCI controller's entry had to move from its parent node
so as to be recognized properly by FBSD.
PCI was enabled in kernel configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4379
uart_dev_ns8250 now relies on compatible property instead of additional
'busy-detect' cell. All drivers with compatible = "snps,dw-apb-uart" have
busy detection turned on. DTS files of devices affected by the change
were modified and 'busy-detect' property was removed.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4218
Ranges property of 'soc' node used two-cell addresses which resulted in
casting errors as simplebus resource allocation works with 32-bit u_long
variables. FDT ranges were simplified.
Reviewed by: imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4212
This commit introduces initial support for Marvell Armada38x platform.
Changes:
- Add common DTS files for Armada38x SoCs and DTS file for A388-GP
- Add ARMADA38X kernel configuration
- Add option SOC_MV_ARMADA38X and set MV_PCI_PORTS
- Add list of files to compile
- Implement get_tclk(), get_sar_value(), cpu_reset() functions
- Add CPU ID and SoC numbers
- Correct ifdefs in arm/mv/timer.c
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4210
Zybo needs its own DTB and has a different PHY, so add it to
the base kernel. Details on building bootable SD images at
http://www.thomasskibo.com/zedbsd/
Submitted By: Thomas Skibo
so they were disabled during DTS transition. Though there are
no standard devices/drivers on them people might use iic(4) userland
interface to access these buses.
