Add MEMORY_BARRIER for the few scratch dma ops that were missing
them plus add a couple of hi 32 bit dma ops (we could probably
allow 64 bit scratch and request/response queue dma now).
install custom pager functions didn't actually happen in practice (they
all just used the simple pager and passed in a local quit pointer). So,
just hardcode the simple pager as the only pager and make it set a global
db_pager_quit flag that db commands can check when the user hits 'q' (or a
suitable variant) at the pager prompt. Also, now that it's easy to do so,
enable paging by default for all ddb commands. Any command that wishes to
honor the quit flag can do so by checking db_pager_quit. Note that the
pager can also be effectively disabled by setting $lines to 0.
Other fixes:
- 'show idt' on i386 and pc98 now actually checks the quit flag and
terminates early.
- 'show intr' now actually checks the quit flag and terminates early.
actually go write the config page. This fixes the long standing
problem about updating NVRAM on Fibre Channel cards and seems
so far to not break SPI config page writes.
Put back role setting into mpt. That is, you can set a desired role
for mpt as a hint. On the next reboot, it'll pick that up and redo
the NVRAM settings appropriately and warn you that this won't take
effect until the next reboot. This saves people the step of having
to find a BIOS utilities disk to set target and/or initiator role
for the MPT cards.
significantly reduces booting time when there is broken floppy disk drive,
controller, cable, BIOS, etc.
When the floppy controller interface is correctly implemented, disk change
signal (DSKCHG) is reflected in the Digital Input Register (DIR) at 0x3f7.
However, there are many cases that the signal is unusable. Moreover, some
BIOS does not reserve the port at all. In those cases, the register may not
function.
loading for the QLogic cards.
Because isp(4) exists before the root is mounted, it's not really
possible for us to use the kernel's linker to load modules directly
from disk- that's really too bad.
However, the this is still a net win in in that the firmware has
been split up on a per chip (and in some cases, functionality)
basis, so the amount of stuff loaded *can* be substantially less
than the 1.5MB of firmware images that ispfw now manages. That is,
each specific f/w set is now also built as a module. For example,
QLogic 2322 f/w is built as isp_2322.ko and Initiator/Target 1080
firmware is built as isp_1080_it.ko.
For compatibility purposes (i.e., to perturb folks the least), we
also still build all of the firmware as one ispfw.ko module.
This allows us to let 'ispfw_LOAD' keep on working in existing
loader.conf files. If you now want to strip this down to just
the firmware for your h/w, you can then change loader.conf to
load the f/w you specifically want.
We also still allow for ispfw to be statically built (e.g., for
PAE and sparc64).
Future changes will look at f/w unloading and also role switching
that then uses the kernel linker to load different ips f/w sets.
MFC after: 2 months
Use it to reset controller and to select data rate. According to Intel
80277AA datasheet, software reset behaves the same as DOR reset except
that it is self clearing. National Semiconductor PC8477B datasheet says
the same. As a side effect, we no longer use Configuration Control
Register (CCR) at 0x3f7 for these controllers, which is often missing
in modern hardware.
(and by extension, the 2422).
One peculiar thing I've found with the 2322 is that if you
don't force it to do Hard LoopID acquisition, the firmware
crashes. This took a while to figure out.
While we're at it, fix various bugs having to do with NVRAM
reading and option setting with respect to pieces of NVRAM.
is never taken since there aren't any 802.11a ural(4) sticks available
on the market.
PR: kern/99676
Submitted by: KIYOHARA Takashi
Reviewed by: damien
MFC after: 1 week
tree... John Baldwin noted that sio might pass values between probe
and attach via softc. It appears that sio does leave the hardware in
a known state after probing, so other drivers that try to probe might
leave it in a worse state. It doesn't seem to pass any data in softc,
however, that I could find... I think we should not be probing for
anything but nonPnP isa, but that's a change for another day.
Submitted by: Frank Behrens
PR: 87845
cards: the chips are all marked "RTL8111B", but they put stickers on the
back that say "RTL8168B/8111B". The manual says there's only one HWREV code
for both the 8111B and 8168B devices, which is 0x30000000, but the cards
they sent me actually report HWREV of 0x38000000. Deciding to trust the
hardware in front of me rather than a possibly incorrect manual (it wouldn't
be the first time the HWREVs were incorrectly documented), I changed the
8168 revision code. It turns out this was a mistake though: 0x30000000
really is a valid for the 8168.
There are two possible reasons for there to be two different HWREVs:
1) 0x30000000 is used only for the 8168B and 0x38000000 is only for
the 8111B.
2) There were 8111/8168 rev A devices which both used code 0x30000000,
and the 8111B/8168B both use 0x38000000.
The product list on the RealTek website doesn't mention the existence of
any 8168/8111 rev A chips being in production though, and I've never seen
one, so until I get clarification from RealTek, I'm going to assume that
0x30000000 is just for the 8168B and 0x38000000 is for the 8111B only.
So, the HWREV code for the 8168 has been put back to 0x30000000,
a new 8111 HWREV code has been added, and there are now separate
entries for recognizing both devices in the device list. This will
allow all devices to work, though if it turns out I'm wrong I may
need to change the ID strings
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
latter is a PCIe 10/100 chip.
Finally fix the EEPROM reading code so that we can access the EEPROMs on all
devices. In order to access the EEPROM, we must select 'EEPROM programming'
mode, and then set the EEPROM chip select bit. Previously, we were setting
both bits simultaneously, which doesn't work: they must be set in the
right sequence.
Always obtain the station address from the EEPROM, now that EEPROM
reading works correctly.
Make the TX interrupt moderation code based on the internal timer
optional and turned off by default.
Make the re_diag() routine conditional and off by default. When it is
on, only use it for the original 8169, which was the only device that
that really needed it.
Modify interrupt handling to use a fast interrupt handler and fast
taskqeueue.
Correct the rgephy driver so that it only applies the DSP fixup for
PHY revs 0 and 1. Later chips are fixed and don't need the fixup.
Make the rgephy driver advertise both 1000_FD and 1000_HD bits in
autoneg mode. A couple of the devices don't autoneg correctly unless
configured this way.
