pr_usrreqs. Collapse duplicates with udp_usrreq.c and
tcp_usrreq.c (calling the generic routines in uipc_socket2.c and
in_pcb.c). Calling sockaddr()_ or peeraddr() on a detached
socket now traps, rather than harmlessly returning an error; this
should never happen. Allow the raw IP buffer sizes to be
controlled via sysctl.
negotiation messages may be tagged, we were overrunning the old buffer.
The variable that was getting squashed is updated before the message goes
out, causing corrupted SDTR or WDTR messages. Depending on the phases
traversed before message out, this could cause the wrong offset to be
negotiated allowing data overruns to occur. The problem is easier to
detect with wide targets on the chain since the allowed offset is smaller.
Also removed the unnecessary clearing of SPIORDY during the message out
phase. We don't rely on SPIORDY any more.
non-broken chipssets whose ID is 0x84, such as the one found in the NEC
6030H.
> The code relies on the assumption that on a genuine_broken vlsi, you
> don't get 0x84 when probing slot 1 in the normal location. On the versa I
> do get 0x84 when probing slot 1 in the normal location. What you get on
> genuine_broken at the normal slot 1 location is unknown to me;
Submitted by: Chris Timmons <skynyrd@opus.cts.cwu.edu>
Successful lstat()s purged an existing entry as well as not caching the
result.
This bug was introduced in Lite1 by setting the LOCKPARENT flag for
[o]lstat() in order to support the inherit-attributes-from-parent-
directory misfeature for symlinks. LOCKPARENT was previously only set
for CREATEs and DELETEs. It is now set for LOOKUPs, but only for
[o]lstat(), so the problem wasn't very noticeable.
the old VFS_VFSCONF sysctl is enabled by default.
Initialize the vfc_vfsops field to non-NULL in sysctl_ovfs_conf()
so that the old VFS_VFSCONF sysctl actually works. The old (still
current) getvfsent.c uses this "kernel-only" field to decide which
vfs's are configured (the old implementation returned null entries
for unconfigured vfs's).
will increase the overhead of queueing a command, but some recent bug reports
make me believe that AAP isn't really working and that we are losing some
SCBs from the input queue. Hopefully this will cure that problem.
Fix some bugs in the error recovery code. Mainly these could cause us to
inadvertantly forget to untimeout an SCB that was recovered causing later
confusion.
to coredump previously since it (somewhat uniquely) is setuid and forks
without execing, and thus without passing P_SUGID the child could
coredump and possibly divulge sensitive information (such as encrypted
passwords from the passwd database).
at runtime.
etc/make.conf:
Nuked HAVE_FPU option.
lib/msun/Makefile:
Always build the i387 objects. Copy the i387 source files at build
time so that the i387 objects have different names. This is simpler
than renaming the files in the cvs repository or repeating half of
bsd.lib.mk to add explicit rules.
lib/msun/src/*.c:
Renamed all functions that have an i387-specific version by adding
`__generic_' to their names.
lib/msun/src/get_hw_float.c:
New file for getting machdep.hw_float from the kernel.
sys/i386/include/asmacros.h:
Abuse the ENTRY() macro to generate jump vectors and associated code.
This works much like PIC PLT dynamic initialization. The PIC case is
messy. The old i387 entry points are renamed. Renaming is easier
here because the names are given by macro expansions.
in the route. This allows us to remove the unconditional setting of the
pipesize in the route, which should mean that SO_SNDBUF and SO_RCVBUF
should actually work again. While we're at it:
- Convert udp_usrreq from `mondo switch statement from Hell' to new-style.
- Delete old TCP mondo switch statement from Hell, which had previously
been diked out.
is administratively downed, all routes to that interface (including the
interface route itself) which are not static will be deleted. When
it comes back up, and addresses remaining will have their interface routes
re-added. This solves the problem where, for example, an Ethernet interface
is downed by traffic continues to flow by way of ARP entries.
clusters greater than one page in length by calling contigmalloc1().
This uses a helper process `mclalloc' to do the allocation if
the system runs out at interrupt time to avoid calling contigmalloc
at high spl. It is not yet clear to me whether this works.
sb_max * MCLBYTES / (MSIZE + MCLBYTES)
used in sbreserve() to overflow, causing all socket creation attempts
to fail. Force the calculation to use u_quad_t's, which makes overflow
less likely.
"boot.config" (relative to the root directory on the 'a' partition
on the first BSD slice) if it exists. If it doesn't exist, then
the only visible changes should be that the kernel name isn't reset
to "/kernel" after looking it up fails and that the default name
is now "kernel".
The new function readfile() can be used for other things:
- reading help messages.
- reading splash screens.
- reading userconfig info.
Changed it from 4 to 16 for i386's. It can be anything for i386's,
but compiler options limit it to a power of 2, and assembler and
linker deficiencies limit it to a small power of 2 (<= 16).
We use 16 in the kernel to get smaller tables (see Makefile.i386 and
<machine/asmacros.h>). We still use the default of 4 in user mode.
Use HISTCOUNTER instead of (*kcount) in the definition of KCOUNT()
for consistency with other macros.
- *fs_init routines now take a "struct vfsconf * vfsp" pointer
as an argument.
- Use the correct type for cookies.
- Update function prototypes.
Submitted by: bde
Call vget/VOP_UNLOCK with the correct number of
arguments. Call vn_lock where appropriate.
vfs_goneall is now replaced by VOP_REVOKE.
Submitted by: bde
available in buffer when buffer was completely empty.
It now correctly reports the total buffer space available.
Reviewed by: jkh, davidg
Obtained from: Linux 1.3.20's sound driver code
being used without ever being initialized. From examining
the rest of the routine, it looks like this is a typo,
and it really should have been "1" instead of "i".
Submitted by: mpp
filed in the hardware SCB not changing during the course of a transaction.
Since the sequencer now DMAs the hardware SCB back up to the host when it
detects a residual, this is no longer the case. I added a field to the
"software" scb to mirror this information and it is now used for doing the
residual calculation.
When setting the HCNT registers, do so in ascending order.
When performing tagged queueing in non-paging mode, also check the
disconnected bit in the SCB as extra sanity during a reconection.
Make the labels in the DMA routine more sane.
When doing a DMA, if we see the DMADONE condition come true, we can
simply turn of the DMA enable bits in DFCNTRL without testing the FIFO
state as HDONE is true when DMADONE is true and this emplies the FIFO is
empty.
These changes clear up the data overrun error messages and seem to prevent
the "timed out in data-in phase" problems.
to not return without setting a return value when it
can't read a block error or detects a bad cylinder group,
since the caller is expecting a return value.
It will now panic at this point, since the thing
to do in this case would be to return a "bad block"
status to the caller, and the caller will panic
anyways when that happens.
Also updated to panic strings in this routine to read
"ffs_checkblk: ..." instead of "checkblk: ...".
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
ULTRAENB->FAST20
Add a missing ahc_run_done_queue if a BRKADDRINT occurs. This should never
happen (haven't heard of one happening), but it was still a bug.
Brought the ordered tag sending code up into the tag code to be clearer.
If we decide we should send an ordered tag, only do so for the target that
timed out instead of all targets.
Initialize the STAILQ in ahc_serach__qinfifo. This was causing a panic
during some recovery operations.
Remove the unused varable maxtarget.
free.
When we clear SCSIRATE, also clear the FAST20 bit in SXFRCTL0. This also
allowed me to clean up some of the ULTRA code.
ULTRAENB->FAST20 to follow the convention in the Adaptec data books.
Fix the data-overrun code to set both stcnt and hcnt otherwise, the transfer
will just hang until we get a timeout.
Add implicit support for the NOOP message. I've never heard of the driver
issueing a reject for one, but its silly to reject NOOP and who knows how a
device might react.
In the dma routine, check SDONE before cleaing SDMAEN. The data books mention
SDONE possibly being cleared when SDMAEN is reset. Clients of dma now need
to check if SINDEX is cleared to know if a phasemis occured.
Fix some comments to be correct.
from last time. Some people have pointed out that there were some odd
side-effects in the changes I made. Two things are different:
- sc_print_addr() will print 'foodev0:' (i.e. sd0:, st0:, cd0:, etc...)
if the device name is known. If it's not known, it'll use a longer
notation. This shortens error messages back to a sane length.
- Added a small function called sc_print_init() to set the sc_printing
flag so that sc_print_addr() will know that we want it to print a
linefeed. Used this in scsi_device_attach() to restore proper carriage
return printing behavior which I broke.
Remaining bogons: the NCR SCSI driver prints out information while the
device-specific attach routine is running with its own linefeeds. This
breaks up the individual messages emitted by the subdriver modules and
causes at least one message to appear on a line by itself without a
device spec prefix. I'm not sure of the correct way to fix this, and
I don't have any NCR SCSI hardware to test with anyway.
There's probably more, but I gather that a rewrite of the SCSI subsystem
is pending anyway, so I'll leave the rest to Those Who Know More About
This Than I (tm).
complained so it cannot be entirely bad :-)
I include the email that probably explains it for people who already know:
> >Compiling with -O3 inlines functions. However the function that is being
> >inlined in makeinfo.c (add_word_args()) is a vararg function and must not be
> >inlined.
> >
> >The code in question is K&R style, and AFIK, there is no way for the compiler
> >to determine that the function uses vararg. Either change the code to use
> >prototypes, or use stdarg, or add a directive to prevent inlining.
>
> Not declaring a varargs function as varargs before it is used gives
> undefined behaviour.
>
> However, in practice the bug is probably in FreeBSD's <varargs.h>, which
> doesn't use gcc's __builtin_next_arg(). gcc should notice that it is
> used and not inline functions that have it. <stdarg.h.> uses it, but I
> think there's another gcc builtin that it should be using.
Patch attached. The ellipsis causes gcc to flag this as a varargs function,
and the name "__builtin_va_alist" is special cased in gcc to hide the last
argument in the arglist.
Reviewed by: bde & phk
Submitted by: jlemon@americantv.com (Jonathan Lemon)
The PS/2 mouse device responds to a reset command with a sequence of
ACK(fa), RESULT(aa) and ID(00). Most PS/2 mice immediately returns
ACK, but spend sometime before sending RESULT. The Armada takes time
before ACK; extra delay is necessary before the call to read ACK.
The problem was reported in comp.unix.bsd.freebsd.misc and the patch
was tested by the reporter. No PR was filed, by the way.
read-mode access to CD-ROM media in the worm(4) driver. No whistles
and bells yet, like all the CDIO* commands, but at least a start.
In order to do this, i had to slightly rearrange the semantics of an
open(2) on the worm driver: now, opening it with O_NONBLOCK set means
no actual IO operations will be intended but only ioctls are to be
processed. This mode is used by wormcontrol(8) to prepare a track
and/or session.
I have only been able to test this on a 2.2-GAMMA system by now, and
only the !DEVFS part is tested yet. Also, i have only done a dummy
burn so far, but wouldn't expect many surprises else. Report bugs to
me ASAP, if there's reasonable demand and i hear no objections, i
might consider merging it into the 2.2 branch as well.
