loaded, the tick interrupt enabled and a handler that resets the tick
counter on every tick interrupt. While this isn't documented this can
cause DELAY() to wait for a value the tick counter will not reach when
used in early boot, i.e. before cpu_initclocks() is called, depending
on when in the cycle DELAY() is called, the delay value and the value
the tick compare register is set to. The excessive use of DELAY() in
uart(4) when probing Sun keyboards seems to always manage to trigger
this, resulting in a hang during boot.
Disable the tick interrupt in tick_init(), which is called early in
sparc64_init(), until the interrupt is enabled again in tick_start(),
called by cpu_initclocks(), with our own handler. This fixes the hang
during probing Sun keyboards on AXi boards and Ultra 10, with other
machines like Ultra 5 probably being affected but not tested.
Additional testing by: Matthias Muthmann
MFC after: 1 week
for nodes hanging off of Central (untested), FireHose (untested) and
PCI (tested) busses.
- Add an additional parameter to OF_decode_addr() which specifies the
index of the register bank to decode.
These should allow to eventually add support for the Z8530 hanging off of
FireHose to uart(4) and to write support for PCI-based graphics adapters.
Suggested by: tmm (back in '03)
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.
Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.
o Disable ofw_console(4), sab(4) and zs(4).
sab(4) and zs(4) are disabled because the hardware controlled by
them is handled by uart(4)+puc(4) and the latter combination is
functionally complete and up to date.
ofw_console(4) is disabled because it doesn't claim the device it
controls (through OFW) and thus interferes with puc(4)+uart(4),
which has sufficient knowledge to extract the necessary information
from OFW to setup the console. Put differently, ofw_console(4) is
not a proper device driver and can only do harm. Its functionality
is completely handled by uart(4).
This commit makes uart(4) the default driver for serial ports.
MFC after: 2 weeks
bridge in the device tree which lacks the mandatory (also by the OFW PCI
bus binding spec) "reg" property. Change the code to just ignore nodes
missing the "reg" property instead of panicing when encountering such a
node. Also ignore nodes without a "name" property (guaranteed by the OFW
PCI bus binding spec). This brings the behaviour of the MD OFW PCI code
regarding such incomplete nodes in line with the EBus and the SBus code.
Tested by: Cyril Tikhomiroff <tikho@anor.net>
MFC after: 1 month
now use a pool mutex to manage the reference counts. This fixes races
resulting in use-after-free.
Tested by: kris, David Cornejo dave at dogwood dot com
Reported by: bmilekic's MemGuard
MFC after: 1 week
won't exist for EBus. Just fail the allocation by returning NULL.
Now drivers that are MI can try resources that the driver knows may
be used by the device.
on entry and it assumes the responsibility for releasing the page queues
lock if it must sleep.
Remove a bogus comment from pmap_enter_quick().
Using the first change, modify vm_map_pmap_enter() so that the page queues
lock is acquired and released once, rather than each time that a page
is mapped.
In such cases, the busying of the page and the unlocking of the
containing object by vm_map_pmap_enter() and vm_fault_prefault() is
unnecessary overhead. To eliminate this overhead, this change
modifies pmap_enter_quick() so that it expects the object to be locked
on entry and it assumes the responsibility for busying the page and
unlocking the object if it must sleep. Note: alpha, amd64, i386 and
ia64 are the only implementations optimized by this change; arm,
powerpc, and sparc64 still conservatively busy the page and unlock the
object within every pmap_enter_quick() call.
Additionally, this change is the first case where we synchronize
access to the page's PG_BUSY flag and busy field using the containing
object's lock rather than the global page queues lock. (Modifications
to the page's PG_BUSY flag and busy field have asserted both locks for
several weeks, enabling an incremental transition.)
These devices should be probed first because they are at fixed
locations and cannot be turned off. ISA PNP devices, on the other
hand, can be turned off and often can be flexible in the resources
they use. Probe them last, as always.
specified register, but a pointer to the in-memory representation of
that value. The reason for this is twofold:
1. Not all registers can be represented by a register_t. In particular
FP registers fall in that category. Passing the new register value
by reference instead of by value makes this point moot.
2. When we receive a G or P packet, both are for writing a register,
the packet will have the register value in target-byte order and
in the memory representation (modulo the fact that bytes are sent
as 2 printable hexadecimal numbers of course). We only need to
decode the packet to have a pointer to the register value.
This change fixes the bug of extracting the register value of the P
packet as a hexadecimal number instead of as a bit array. The quick
(and dirty) fix to bswap the register value in gdb_cpu_setreg() as
it has been added on i386 and amd64 can therefore be removed and has
in fact been that.
Tested on: alpha, amd64, i386, ia64, sparc64
clock found on the ISA bus (some USIIe, USIIi and USIIIi models) and
EBus (USIII models) instead of a MK48Txx clock.
Testet by: Matthew T. Lager" <freebsd@trinetworks.com> on Sun Fire V100,
Xavier Beaudouin <kiwi@oav.net> on Netra X1 (initial version)
- The claim in the commit log of rev. 1.11 of dev/uart/uart_cpu_sparc64.c
etc. that UARTs are the only relevant ISA devices on sparc64 turned out
to be false. While there are sparc64 models where UARTs are the only
devices on the ISA bus there are in fact also low-cost models where all
devices traditionally found on the EBus are hooked up to the ISA bus.
There are also models that use a mix between EBus and ISA devices with
things like an AT keyboard controller and other rather interesting
devices that we might want to support in the futute hook up to the ISA
bus.
In order to not need to add sparc64 specific device_identify methods to
all of the respective ISA drivers and also not add OFW specific code to
the common ISA code make the sparc64 ISA bus code fake up PnP devices so
most ISA drivers probe their devices without further changes.
Unfortunately Sun doesn't adhere to the ISA bindings defined in IEEE
1275-1994 for the properties of most of the ISA devices which would
allow to obtain the vendor and logical IDs from their properties. So we
we just use a simple table which maps the name properties to PnP IDs.
This could be done in a more sophisticated way but I courrently don't
see the need for this. [1]
- Add the children with fully mapped and specified resources (in the OFW
sense) similar to what is done in the EBus code for the IRQ resources
of the children as adjusting the resources and the resource list entries
respectively in isa_alloc_resource() as done perviously causes trouble
with drivers which use rman_get_start(), pass-through or allocate and
release resources multiple times, etc.
Adjusting the resources might be better off in a bus_activate_resource
method but the common ISA code currently doesn't allow for an
isa_activate_resource(). [2]
With this change:
- ppbus(4) and lpt(4) attach and work (modulo ECP mode, which requires
real ISADMA code but it currently only consists of stubs on sparc64).
- atkbdc(4) and atkbdc(4) attach, no further testing done.
- fdc(4) itself attaches but causes a hang while attaching fd0 also
when is DMA disabled, further work in fdc(4) is required here as e.g.
fd0 uses the address of fd1 on sparc64 (not sure if sparc64 supports
more than one floppy drive at all).
All of these drivers previously caused panics in the sparc64 ISA code.
- Minor changes, e.g. use __FBSDID, remove a dupe word in a comment and
declare one global variable which isn't used outside of isa.c static.
o dev/uart/uart_cpu_sparc64.c and modules/uart/Makefile:
- Remove the code for registering the UARTs on the ISA bus from the
sparc64 uart_cpu_identify() again and rely on probing them via PnP.
Original idea by: tmm [1]
No objections by: tmm [1], [2]
I have in mind for the genclock interface):
- Recognize the MK48T18 as well (differs from the MK48T08 only in
packaging options and voltages).
- Allow MD code to provide functions for reading/writing NVRAM/RTC
locations.
If passed NULL, the old behaviour using bus_space_{read,write}_1() is
used. Otherwise, all access to the chip goes via the MD functions.
This is necessary for mvmeppc boards where the mk48txx NVRAM/RTC is
not directly addressable.
- Cleanup MI mk48txx(4) todclock driver:
- Prepare mk48txxvar.h and leave only register definitions in
mk48txxreg.h.
- Define struct mk48txx_softc as usual devices and allocate necessary
members in it.
- Change mk48txx_attach() to only take a device_t.
o While converting the sparc64 eeprom driver to the above changes:
- Remove some dead code and stale comments.
- Use the NVRAM size provided by the mk48txx driver instead of hardcoding
it as suggested by a comment.
- Add a comment about why it doesn't make much sense to read the hostid
directly from the NVRAM except for displaying it when attaching.
- Don't print the hostid if it reads all zero because it's stored
elsewhere.
Change the spelling of the "catch" option to be consistent with the new
options. Implement the "no wait" option. An implementation of the "CPU
private" for i386 will be committed at a later date.
need for most calls to vm_page_busy(). Specifically, most calls to
vm_page_busy() occur immediately prior to a call to vm_page_remove().
In such cases, the containing vm object is locked across both calls.
Consequently, the setting of the vm page's PG_BUSY flag is not even
visible to other threads that are following the synchronization
protocol.
This change (1) eliminates the calls to vm_page_busy() that
immediately precede a call to vm_page_remove() or functions, such as
vm_page_free() and vm_page_rename(), that call it and (2) relaxes the
requirement in vm_page_remove() that the vm page's PG_BUSY flag is
set. Now, the vm page's PG_BUSY flag is set only when the vm object
lock is released while the vm page is still in transition. Typically,
this is when it is undergoing I/O.
control the number of lines per page rather than a constant. The variable
can be examined and changed in ddb as '$lines'. Setting the variable to
0 will effectively turn off paging.
- Change db_putchar() to force out pending whitespace before outputting
newlines and carriage returns so that one can rub out content on the
current line via '\r \r' type strings.
- Change the simple pager to rub out the --More-- prompt explicitly when
the routine exits.
- Add some aliases to the simple pager to make it more compatible with
more(1): 'e' and 'j' do a single line. 'd' does half a page, and
'f' does a full page.
MFC after: 1 month
Inspired by: kris
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
be used to announce various system activity.
The auxio device provides auxiliary I/O functions and is found on various
SBus/EBus UltraSPARC models. At present, only front panel LED is
controlled by this driver.
Approved by: jake (mentor)
Reviewed by: joerg
Tested by: joerg
MP machines (hopefully). CPU timers are OK on UP machines but we
don't keep the timers in sync on MP machines so if the CPU's timer
is chosen as the primary timecounter it's possible for time to
not be monotonically increasing because different CPU's counters
may be used at different times. But the CPU's counters are otherwise
one of the higher quality counters available. So, on UP machines
we'll use a relatively high quality value but on MP machines we'll
use a quality that should prevent the CPU's counters from being chosen.
Requested by: green (who did the first version of the patch)
Reviewed by: marius, green
MFC after: 1 week
the structure space had been obtained from malloc() its contents is
random garbage. The choice of value being set is part of a larger effort
to solve some timecounter issues on MP machines (while working on that
we noticed this problem).
Noticed by: marius
Reviewed by: marius, green
MFC after: 3 days
longer than 'normal'. The cause is still being tracked down but
in the meantime there are machines where raising IPI_RETRIES does
help - it's not just a case of the machine staying locked up longer
and then panic-ing anyway. Several helpful folks on sparc64@ tried
a patch that helped figure out what to raise this number to.
Discussed on: sparc64@
MFC after: 3 days
MAXWIN to the register window manipulation functions - rwindow_load()
calls rwindow_save() so this one addition should take care of both.
This should help find places that pcb_nsaved doesn't get initialized
properly.
Suggested by: jake
for the new thread. The rest of the fields in the pcb wind up being
written to before they're read as a normal part of the pcb usage but
this field may be read upon return to userland, having it be uninitialized
garbage is bad.
Submitted by: Andrew Belashov (bel at orel dot ru)
Reviewed by: jake
MFC after: 3 days
