since the link takes a bit to negotiate, the information is pretty
much never available during the probe. As such, the boot output
pretty much always prints N/A for speed and duplex. Since we print
out the output of ifconfig during the user space boot, this early
boot information is also generally redundant, and added to the noise.
MFC after: 2 weeks
before dereferencing it. Certain corrupt kernel modules might not have
a valid hash table, and would cause a kernel panic when they were loaded.
Instead of panic'ing, the kernel now prints out a warning that it is
missing the symbol hash table.
Tested by: Benjamin Close Benjamin dot Close at clearchain dot com
MFC after: 1 week
PCI-ISA bridge. Thus, when viapm0 or viapropm0 attaches, isab0 dosen't
attach so there is no isa0 bus hung off of that bridge. In the non-ACPI
case, legacy0 will add an isa0 anyway as a fail-safe, but ACPI assumes that
any ISA bus will be enumerated via a bridge. To fix this, call
isab_attach() to attach an isa0 ISA child bus device if the pm or propm
device we are probing is a PCI-ISA bridge. Both drivers now have to
implement the bus_if interface via the generic methods for resource
allocation, etc. to work. Also, we now add 2 new ISA bus drivers that
attach to viapm and viapropm devices.
PR: kern/87363
Reported by: Oliver Fromme olli at secnetix dot de
Tested by: glebius
MFC after: 1 week
- Prefer '_' to ' ', as it results in more easily parsed results in
memory monitoring tools such as vmstat.
- Remove punctuation that is incompatible with using memory type names
as file names, such as '/' characters.
- Disambiguate some collisions by adding subsystem prefixes to some
memory types.
- Generally prefer lower case to upper case.
- If the same type is defined in multiple architecture directories,
attempt to use the same name in additional cases.
Not all instances were caught in this change, so more work is required to
finish this conversion. Similar changes are required for UMA zone names.
in bytes to start off with. This caused the GPT geom sniffer to attempt
a seek just back from the end of the 'disk', which resulted in a > 4G
seek, causing gdb psim to exit since it only supports 32-bit seeks.
The size of the disk should really be specified in the psim device tree,
but for now do the minimal amount of work to get psim to run again.
aac_alloc_sync_fib(). aac_alloc_sync_fib() will assert that the I/O locks
are held. This fixes a panic on system boot up when the aac(4) device's
bus_generic_attach() routine is called.
Reviewed by: scottl
OpenFirmware. FreeBSD/ppc uses SPRG0 as the per-cpu data area pointer,
and SPRG1-3 as temporary registers during exception handling. There
have been a few instances where OpenFirmware does require these to
be part of it's context, such as cd-booting an eMac.
reported by: many
MFC after: 3 days
following the protocol pru_listen() call to solisten_proto(), so
that it occurs under the socket lock acquisition that also sets
SO_ACCEPTCONN. This requires passing the new backlog parameter
to the protocol, which also allows the protocol to be aware of
changes in queue limit should it wish to do something about the
new queue limit. This continues a move towards the socket layer
acting as a library for the protocol.
Bump __FreeBSD_version due to a change in the in-kernel protocol
interface. This change has been tested with IPv4 and UNIX domain
sockets, but not other protocols.
that caused a premature exit after calling a fast interrupt handler
and bypassing a much needed critical_exit() and the scheduling of
the interrupt thread for non-fast handlers. In short: unbreak :-)
- Return EINVAL if play_format or rec_format is set but the corresponding
sample rate is 0.
- Don't try to set the playback or recording format to 0. Previously,
issuing an AIOSFMT ioctl with an all-zeroes snd_chan_param would
trigger a KASSERT in chn_fmtchain(); I'm unsure about the effects on
a kernel without INVARIANTS. After this commit, issuing AIOSFMT with
an all-zeroes snd_chan_param is equivalent to issuing AIOGFMT.
MFC after: 2 weeks
trying to access user-space stack addresses when a user fault
is encountered, as occurs when GEOM KTR code is handling a page fault
and is using stack_save() to capture a trace for debug purposes.
It may be possible to walk beyond the trap-frame if it is a kernel fault,
as db_backtrace() does, but I don't think that complexity is needed in
this routine.
MFC after: 3 days
convert to or from timeval frequently.
Introduce function itimer_accept() to ack a timer signal in signal
acceptance code, this allows us to return more fresh overrun counter
than at signal generating time. while POSIX says:
"the value returned by timer_getoverrun() shall apply to the most
recent expiration signal delivery or acceptance for the timer,.."
I prefer returning it at acceptance time.
Introduce SIGEV_THREAD_ID notification mode, it is used by thread
libary to request kernel to deliver signal to a specified thread,
and in turn, the thread library may use the mechanism to implement
SIGEV_THREAD which is required by POSIX.
Timer signal is managed by timer code, so it can not fail even if
signal queue is full filled by sigqueue syscall.
actual resource values we received from the system rather than the range
we requested. Since we request a range starting at 0, we would record
that number. Later, since this == 0, we'd allocate again. However,
we wouldn't write the new resource into the BAR. This resulted in
a resource leak as well as a BAR that couldn't access the resource at
all since rman_get_start, et al, were wrong.
MFC After: 1 week (assuming RELENG_6 is open for business)
the ifp, so you can't call it before doing if_alloc(). Also, there's
really no need to call it here anyway: the code I originally ported from
OpenBSD incorrectly set the station address only once at device attach
time, instead of setting in txp_init(). This meant you couldn't change
the address with ifconfig txp0 ether xx:xx:xx:xx:xx:xx. I added the
call to txp_set_filter() in txp_init() to correct this, but forgot to
remove the call from txp_attach(). Until now, it never mattered.
With this fix, the txp driver tests good:
txp0: <3Com 3cR990-TX-97 Etherlink with 3XP Processor> port 0xb800-0xb87f mem 0xe6800000-0xe683ffff irq 12 at device 10.0 on pci0
txp0: Ethernet address: 00:01:03:d4:91:4f
and channel to ifconfig. Also use the SSID and channel info from
the association info that we already have instead of using ndis_get_info()
to ask the driver for it again.
memory for request.
I was sure graid3 should handle such situations well, but green@ reported
it is not and we want to fix it before 6.0.
Submitted by: green
kern/87959 cracauer ext2fs: no cp(1) possible, mmap returns EINVAL
ext2fs was missing vnode_create_vobject.
(Reisefs probably has the same problem but I want to get this in quick
for 6-release)
drivers I started quite some time before.
Retire the old i386-only pcf driver, and activate the new general
driver that has been sitting in the tree already for quite some
time.
Build the i2c modules for sparc64 architectures as well (where I've
been developing all this on).
o Fix typo in comment
o s/-100/BUS_PROBE_GENERIC/
o s/err/error/ for consistency
o Remove non-applicable comment
o Allow uart_bus_probe() to return the predefined BUS_PROBE_*
contants. In this case: explicitly test for error > 0.
With this change, the driver tests good (at least on i386):
wb0: <Winbond W89C840F 10/100BaseTX> port 0xb800-0xb87f mem 0xe6800000-0xe680007f irq 12 at device 10.0 on pci0
miibus1: <MII bus> on wb0
amphy0: <Am79C873 10/100 media interface> on miibus1
amphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wb0: Ethernet address: 00:00:e8:18:2a:02
wb0: link state changed to DOWN
wb0: link state changed to UP
- Add locked variants of init() and start().
- Use callout_*() to manage callout.
- Test IFF_DRV_RUNNING rather than IFF_UP in wb_intr() to see if we are
still active when an interrupt comes in.
I couldn't find any of these cards anywhere to test on myself, and google
turns up references to FreeBSD and OpenBSD manpages for this driver when
trying to locate a card that way. I'm not sure anyone actually uses these
cards with FreeBSD.
Tested by: NO ONE (despite repeated requests)
I had to initialize the ifnet a bit earlier in attach so that the
if_printf()'s in vr_reset() didn't explode with a page fault.
- Use M_ZERO with contigmalloc() rather than an explicit bzero.
even initialized it, but it never used it.
- Use callout_*() to manage the callout.
- Use m_devget() to copy data out of the rx buffers rather than doing it
all by hand.
- Use m_getcl() to allocate mbuf clusters rather than doing it all by hand.
- Don't free the software descriptor for a rx ring entry if we can't
allocate an mbuf cluster for it. We left a dangling pointer and never
reallocated the entry anyway. OpenBSD's code (from which this was
derived) has the same bug.
Tested by: NO ONE (despite repeated requests)
Reviewed by: wpaul (5)
gdb(1) command better, though I must admit it's confusing: these
files have not only [debugging] symbols, but much more than that.
Requested by: obrien
'device npx' (both of which aren't really optional right now) and
'device io' and 'device mem' (to preserve POLA for 4.x users upgrading
to 6.0) from GENERIC into DEFAULTS.
Requested by: scottl
Reviewed by: scottl
set. When watchdogd(1) is terminated intentionally it clears the bit,
which should then disable it in the kernel.
PR: kern/74386
Submitted by: Alex Hoff <ahoff at sandvine dot com>
Approved by: phk, rwatson (mentor)
can't acquire an sx lock in ttyinfo() because ttyinfo() can be called
from interrupt handlers (such as atkbd_intr()). Instead, go back to
locking the process group while we pick a thread to display information for
and hold that lock until after we drop sched_lock to make sure the
process doesn't exit out from under us. sched_lock ensures that the
specific thread from that process doesn't go away. To protect against
the process exiting after we drop the proc lock but before we dereference
it to lookup the pid and p_comm in the call to ttyprintf(), we now copy
the pid and p_comm to local variables while holding the proc lock.
This problem was found by the recently added TD_NO_SLEEPING assertions for
interrupt handlers.
Tested by: emaste
MFC after: 1 week
our kernel linker will only load PT_LOAD segments, apparently not.
Instead, produce .dbg objects from .debug objects, and install
them together with non-debug objects, as described in objcopy(1).
Original code by: obrien
debug.kdb.panic and debug.kdb.trap alongside the existing debug.kdb.enter
sysctl. 'panic' causes a panic, and 'trap' causes a page fault. We used
these to ensure that crash dumps succeed from those two common failure
modes. This avoids the need for creating a 'panic' kld module.
* Don't recursively panic if we've already paniced and the local apic is
now stuck.
* Add hw.apic.* tunables/sysctls for extint controls
* Change "lapic%d timer" to "cpu%d timer" intname to match i386
the start of the section headers has to take into account the fact
that the image_nt_header is really variable sized. It happens that
the existing calculation is correct for _most_ production binaries
produced by the Windows DDK, but if we get a binary with oddball
offsets, the PE loader could crash.
Changes from the supplied patch are:
- We don't really need to use the IMAGE_SIZEOF_NT_HEADER() macro when
computing how much of the header to return to callers of
pe_get_optional_header(). While it's important to take the variable
size of the header into account in other calculations, we never
actually look at anything outside the non-variable portion of the
header. This saves callers from having to allocate a variable sized
buffer off the heap (I purposely tried to avoid using malloc()
in subr_pe.c to make it easier to compile in both the -D_KERNEL and
!-D_KERNEL case), and since we're copying into a buffer on the
stack, we always have to copy the same amount of data or else
we'll trash the stack something fierce.
- We need <stddef.h> to get offsetof() in the !-D_KERNEL case.
- ndiscvt.c needs the IMAGE_FIRST_SECTION() macro too, since it does
a little bit of section pre-processing.
PR: kern/83477
threads can wait for a thread to exit, and safely assume that the thread
has left userland and is no longer using its userland stack, this is
necessary for pthread_join when a thread is waiting for another thread
to exit which has user customized stack, after pthread_join returns,
the userland stack can be reused for other purposes, without this change,
the joiner thread has to spin at the address to ensure the thread is really
exited.
and ndis_halt_nic(). It's been disabled for some time anyway, and
it turns out there's a possible deadlock in NdisMInitializeTimer() when
acquiring the miniport block lock to modify the timer list: it's
possible for a driver to call NdisMInitializeTimer() when the miniport
block lock has already been acquired by an earlier piece of code. You
can't acquire the same spinlock twice, so this can deadlock.
Also, implement MmMapIoSpace() and MmUnmapIoSpace(), and make
NdisMMapIoSpace() and NdisMUnmapIoSpace() use them. There are some
drivers that want MmMapIoSpace() and MmUnmapIoSpace() so that they can
map arbitrary register spaces not directly associated with their
device resources. For example, there's an Atheros driver for
a miniPci card (0x168C:0x1014) on the IBM Thinkpad x40 that wants
to map some I/O spaces at 0xF00000 and 0xE00000 which are held by
the acpi0 device. I don't know what it wants these ranges for,
but if it can't map and access them, the MiniportInitialize() method
fails.
o Oxford Semiconductor PCI Dual Port Serial
o Netmos Nm9845 PCI Bridge with Dual UART
Add PCI IDs for single-port cards:
o Various SIIG Cyber Serial
o Oxford Semiconductor OXCB950 UART
Update description as per puc(4).
immediately, back off to the next higher Cx sleep state. Some machines
with a Via chipset report a valid C3 but a register read doesn't actually
halt the CPU. This would cause the machine to appear unresponsive as it
repeatedly called cpu_idle() which immediately returned. Causing interrupts
(i.e. by pressing the power button) would cause the system to make forward
progress, showing that it wasn't actually hung.
Also, enable interrupts a little earlier. We don't need them disabled
to calculate the delta time for the read.
Reported by: silby
MFC after: 2 weeks
and increase flexibility to allow various different approaches to be tried
in the future.
- Split struct ithd up into two pieces. struct intr_event holds the list
of interrupt handlers associated with interrupt sources.
struct intr_thread contains the data relative to an interrupt thread.
Currently we still provide a 1:1 relationship of events to threads
with the exception that events only have an associated thread if there
is at least one threaded interrupt handler attached to the event. This
means that on x86 we no longer have 4 bazillion interrupt threads with
no handlers. It also means that interrupt events with only INTR_FAST
handlers no longer have an associated thread either.
- Renamed struct intrhand to struct intr_handler to follow the struct
intr_foo naming convention. This did require renaming the powerpc
MD struct intr_handler to struct ppc_intr_handler.
- INTR_FAST no longer implies INTR_EXCL on all architectures except for
powerpc. This means that multiple INTR_FAST handlers can attach to the
same interrupt and that INTR_FAST and non-INTR_FAST handlers can attach
to the same interrupt. Sharing INTR_FAST handlers may not always be
desirable, but having sio(4) and uhci(4) fight over an IRQ isn't fun
either. Drivers can always still use INTR_EXCL to ask for an interrupt
exclusively. The way this sharing works is that when an interrupt
comes in, all the INTR_FAST handlers are executed first, and if any
threaded handlers exist, the interrupt thread is scheduled afterwards.
This type of layout also makes it possible to investigate using interrupt
filters ala OS X where the filter determines whether or not its companion
threaded handler should run.
- Aside from the INTR_FAST changes above, the impact on MD interrupt code
is mostly just 's/ithread/intr_event/'.
- A new MI ddb command 'show intrs' walks the list of interrupt events
dumping their state. It also has a '/v' verbose switch which dumps
info about all of the handlers attached to each event.
- We currently don't destroy an interrupt thread when the last threaded
handler is removed because it would suck for things like ppbus(8)'s
braindead behavior. The code is present, though, it is just under
#if 0 for now.
- Move the code to actually execute the threaded handlers for an interrrupt
event into a separate function so that ithread_loop() becomes more
readable. Previously this code was all in the middle of ithread_loop()
and indented halfway across the screen.
- Made struct intr_thread private to kern_intr.c and replaced td_ithd
with a thread private flag TDP_ITHREAD.
- In statclock, check curthread against idlethread directly rather than
curthread's proc against idlethread's proc. (Not really related to intr
changes)
Tested on: alpha, amd64, i386, sparc64
Tested on: arm, ia64 (older version of patch by cognet and marcel)
to the actual dates when code actually changed. Also add special case
link state change handling for RELENG_5, which doesn't have
if_link_state_change(). No actual operational changes are done.
devices can be opened multiple times simultaneously but we're
expected to be able to do so by the rest of the loader.
This fixes booting from disks attached to the on-board SCSI
controller of Sun Ultra 1 (previously this triggered a trap)
and probably also of AX1115 boards.
- While here, remove unused variables and add empty lines where
style(9) requires such.
Tested on: powerpc (grehan), sparc64
MFC after: 1 month
Try to make everyone happy: David (to have debug kernels installed
by default), Warner (to be able to override that), and myself (for
actually making it all work and to be consistent).
Now, if kernel was configured for debugging (through DEBUG=-g in
the kernel config file or "config -g"), doing "make install" will
install debug versions of kernel and module objects with their
canonical names,
kernel.debug -> /boot/kernel/kernel
if_fxp.ko.debug -> /boot/kernel/if_fxp.ko
Installing a kernel not configured for debugging, or debug kernel
with INSTALL_NODEBUG variable defined, will install non-debug
kernel and module objects.
Also, restore the install.debug and reinstall.debug targets that
are part of the existing API (they cause some additional gdb(1)
scripts to be installed).
of the PCIR_HDRTYPE register. It's the value returned from this
read access that determines whether or not we decide a device is
present at the current slot index. For some reason that I can't
adequately explain, this read fails on my machine when probing the
USB controller on my machine (which happens a multifunction device
at slot index 3 hung off the PCI-PCI bridge on the AMD8111 (bus
index 1)). The read will return 0xFF even though it should return
0x80 to indicate the presence of a multifunction device.
As near as I can tell, there's some timing issue involved with reading
the 'dead' slot indexes 0 through 2 that causes the read of the actual
device at slot 3 to fail. I tried a couple of different tricks to
correct the problem (the patch to amd64/pci/pci_cfgreg.c fixes it
for the amd64 arch), but adding this delay is the only thing that
always allows the USB controllers to be correctly probed 100% of the
time. Whatever the problem is, it's likely confined to the AMD8111
chipset. However, a simple 1us delay is fairly harmless and should
have no side effects for other hardware. I consider this to be
voodoo, but it's fairly benign voodoo and it makes my USB keyboard
and mouse work again.
Note that this is the second time that I've had to resort to a
1us delay to fix a PCI-related problem with this AMD8111/Opteron
system (the first being a fix I made a while back to the NDISulator).
It's possible the delay really belongs in the cfgreg code itself,
or that pci_cfgreg needs some custom hackery for an errata in the
8111. (I checked but couldn't find any documented errata on AMD's
site that could account for these problems.)
other OSes (Solaris, Linux, VxWorks). It's not necessary to write a 0
to the config address register when using config mechanism 1 to turn
off config access. In fact, it can be downright troublesome, since it
seems to confuse the PCI-PCI bridge in the AMD8111 chipset and cause
it to sporadically botch reads from some devices. This is the cause
of the missing USP ports problem I was experiencing with my Sun Opteron
system.
Also correct the case for mechanism 2: it's only necessary to write
a 0 to the ENABLE port.
