chipset. Add support for this card. Office Max has them on sale and
I was surprised that we didn't have it in our supported list when I
plugged it in...
than the generic ne-2000 string. This should have no effect on the
actual support of the parts, just reporting what the part was.
Also, rename a few functins and symbols to reflect a more generic
part support that grew out of the early specific support.
and into the bus front ends. For ISA and C-BUS cards, we always need
to grab it. For PC Card, already committed, we need to do some sanity
checking on the data that's in the ROMs before we decide that they are
OK to use. The PC Card code has already been committed and is
independent of this code (which also has to work on NE-1000 cards,
assuming that those cards still work :-).
with the latest changes. They actually have valid ROM data at location
0 of memory, just like a real NE-2000 ISA card. Use this data, if
the ROM passes a few basic tests, as an additional source for the MAC
address. Prefer the CIS over this source, but have it take precidence
over falling back to reading the attribtue memory.
o Minor cleanup of a few devices that we match on based on CIS string.
proper way, or at least the same way that NetBSD and Linux do things
(I've been unable to obtain datasheets for these parts to know for
sure). This has some marginal improvement in the DL10022 and DL10019
cards that I have. Also, report which type, exactly.
# There's one or two ed cards that I have which still don't work, but I think
# that's due to MII losage on the card that's not presently compensated
# for in the MII drivers.
tree since 2003/02/20, and I recently cleaned it up. I'd even closed
the PR that I obtained this from Fri Jul 18 23:25:08 MDT 2003 since
I looked at my p4 tree.
PR: 46889
Submitted by: HASEGAWA Tomoki
o Add a fallback location for the MAC address. Most of the early ne2000
PC Cards were built from the same parts, so most of them have the same
address in the CIS to grab the MAC from. Use this address as our
fallback if we don't find anything better.
o Add printf, in bootverbose, noting the MAC addresses that we find along
the way.
# Better sanity checking of the MAC address is needed. Will have to
# investigate using/creating a centralized function to do this as a number
# of other PC Card drivers each have their own ad-hoc tests.
at some offset. Unlike newer cards, the MAC address wasn't part of
the CIS as a specific FUNCE. These older cards were having their MAC
address show up as 0:2:4:6:8:a because that's what's in the ROM
locations that would be there in a real ne2000.
This patch allows one to specify the offset for the MAC address for
these cards. Specify one for the IBM Ethernet II card, as it is one
that has this problem. One shouldn't specify this unless the MAC
address really isn't in the CIS at all.
Side note: The novell probe likely shouldn't read the MAC address, and
that should be moved to the bus specific attach routine(s), maybe as a
convenience function in if_ed_novell.c.
My IBM Ethernet II (aka Info Mover) now has a believable MAC address.
are NOVELL NE2000 with just a tiny quirk that's non vendor specific.
Instead, use the chip_type of DL100XX instead. This is more inline
with how the AX88190 support was added, and seems a little cleaner.
pessmize the error recover path through edintr by calling these
functions, rather than expanding it inline. This error path already
does a lot in it, so an extra function call will be lost in the noise.
It also happens rarely.
while (complicated-expr)
continune;
in preference to
while (complicated-expr);
since the code generated is identical, and the former is easier to read,
especially for complicated-expr that reach to the end of the line...
probing the novell ne[12]000 cards. It should be its own thing, ala
how we do the dl100xx support doing its own thing at the right time.
For the moment, it is just a function, which makes the mainline of the
generic probe easier to follow.
Also, correct a couple of comments that looked wrong.
# there may be a bug in setting up gwether, in that we set
# sc->rec_page_stop based on memsize, rather than sc->mem_size, so if
# these two are different, then the rec_page_stop will be wrong. I'm
# hesitant to fix it without real hardware to test with. Since
# gwether isn't in the hardware list of the man page nor in the commit
# messages, it is hard to know for sure.
and wd80x3 support. Make the obscure ISA cards optional, and add
those options to NOTES on i386 (note: the ifdef around the whole code
is for module building). Tweak pc98 ed support to include wd80x3 too.
Add goo for alpha too.
The affected cards are the 3Com 3C503, HP LAN+ and SIC (whatever that
is). I couldn't find any of these for sale on ebay, so they are
untested. If you have one of these cards, and send it to me, I'll
ensure that you have no future problems with it...
Minor cleanups as well by using functions rather than cut and paste
code for some probing operations (where the function call overhead is
lost in the noise).
Remove use of kvtop, since they aren't required anymore. This driver
needs to get its memory mapped act together, however, and use bus
space. It doesn't right now.
This reduces the size of if_ed.ko from about 51k to 33k on my laptop.
o The COMBO_ECARD comes in many flavors, it seems, so probe both the DL10019
and the AX88x90 on it. Since this seems to work with no ill effects, maybe
the probing should happen more generally rather than being table driven.
Need to think more about this.
o Remove PCM100 because it is duplicative (the ETHERFAST is the pcm100 and
apparently has the same IDs). It was here for NetBSD because they match
up an expected MAC address OID, but since we don't bother with that, we
don't need to be so finely discriminating.
o Minor style nit.
if_ed_isa.c, and they seem to not be helpful anymore.
o Fix style issues from de-Pification.
o change from _isa_ to _cbus_ to the largest extent possible to reflect that
this is really for cbus, not isa.
o Use ANSI function definitions.
o Use ed_clear_memory
o eliminate kvtop
Make the special hp versions match the general ones. Also use fixed
types in the WD80x3_generic probe, and change callers' arrays to
match. Fix a couple of minor style issues by using newstyle function
definitions in a couple places.
if_ed and rename it to ed_detach(). Tell other busses to use this
routine for detach.
Since I don't actually have any non-pccard ed hardware I can test
with, I've only tested with my pccards.
More improvements in this area likely are possible.
Prodded by: rwatson
AX88190 ones, but that one only minorly):
o don't set flags in the match routine. They appear to be cleared
when probe/attach is called. Before this change, they were
always treated as a simple ne2000, which would fail to get the
right NIC address.
o Lookup device again in the probe routine and probe based on the
cards that you see.
o Detect and report the DL10022 seprately from the DL10019 cards.
While I'm here:
o remove a bad printf
o change another bad printf to device_printf.
o minor style(9) formatting tweaks.
# note: a lot of OEM entries are in the ed_pccard_products such that we can
# likely remove, or collapse, many of them.
This makes all of my DL100xx cards at least probe the ethernet address
correctly, which it wasn't doing before. I can't seem to locate my
AX88xxx based cards, so those haven't been tested, but they were
busted before the change so they can't be any worse now...
address, and additional information. Then the printing of the
ethernet address was moved into ether_attach, and so we were printing
orphaned information about the card. Now the probe message is
prefixed by edX:. Prepare for it to move under bootverbose, but don't
move it there yet (the || 1 trick).
versions of the Racore PC Card Ethernet card. Rearrange to reflect
this reality. This ejects IODATA from 0x1bf, which belongs to Racore.
Thanks to Wilko for providing me with a dumpcis for the DEPCM card.
Also, added Nextcom Nexthawk card from NetBSD
there's not dependencies on pccard symboles, such a dependency is not
necessary. This means that drivers that have multiple attachments can
not drag bogus devices into the kernel at load time.
We can't (yet) do this with pci and isa. Drivers written for them
actually do seem to have symbols that depend on these busses'
implementation code.
ndis not touched until other things can be tested.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Discussed in from [FreeBSD-tech-jp 3396] to [FreeBSD-tech-jp 3407]
at FreeBSD-tech-jp@jp.freebsd.org.
NOTE: We must put ed_probe_SIC() function into if_ed_isa.c because
this is a bus dependent code. But the ed driver code is not
separated explicitly whether it is bus dependent or independent
now.
Refer to: http://plaza17.mbn.or.jp/~chi/myprog/FreeBSD/sicat.html
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
is required. NetBSD has one because it checks for the mac address
match as well wanting to give its own string in the description.
Since we do neither, we don't need a separate entry.
# I suspect that a few of the COREGA cards might fall into that category
# as well, but since I don't have access to any of them it is hard to know
# for sure.
enet_mcast fields, so remove them. Sort. Eliminate now duplicate
entries.
This reorg saves about 500 bytes in the binary. I've tested this only
with a couple of cards, so please let me know if I've broken anything.
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o Honor NE2000DVF_{AX88190,DL10019} flags by setting the ED_FLAGS_xxxx
flag.
o Mark linksys combo_ecard as ax88190
o Set the type_str to AX88190 for the ax88190 cards.
This fixes ax88190 based cards, for the most part, but doesn't seem to fix
the mii based dl10019 cards (aka linksys cards).
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
storing a flag in the global variable 'linksys' during the probe
routine and reading it during the attach routine. We now have the
ED_VENDOR_LINKSYS vendor code stored in sc->vendor, so check that
instead.
not from the probe routine. This was an oversight when I originally
ported the miibus support to -current, though it was mostly harmless.
We now set the vendor code to the new value ED_VENDOR_LINKSYS in
ed_pccard_Linksys() at probe time. Then ed_pccard_attach() checks
the vendor code, and sets up the miibus if appropriate.
Reviewed by: imp
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
* a ">" is really ">=" ;
* do not try to fetch zero-sized blocks from the card;
* make sure that bpf gets the packets it wants even with
bridging active;
o Move the ax88190 code to its own function.
o Move all device_method_t, driver_t and DRIVER_MODULE definitions to the
end of files.
o Wrap a few lines > 80 characters.
o Use the same devclass for all ed drivers. This allows machines with
multiple types of cards to have their cards numbered correctly. Before,
you could wind up with two ed0's.
o Protect if_edvar.h from multiple includes because I was there.
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
using a cardbus based system with pccbb providing the pcic interface).
Something isn't quite right.. when the driver allocates and activates
its resources, the IO space that was requested reads as all zeros (versus
the original 0xff's as it normally is when there is no device responding).
Also, deactivate the resources before releasing them. OLDCARD doesn't
seem to care but NEWCARD/CARDBUS get rather unhappy if you release
a resource that hasn't been deactivated yet.
Make pcic_p.c only compile with oldcard kernels.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
first. This will fix a few cards that hang on the WD probe. He tells
me that PAO went one step farther and removed the WD proble completely
and none of the cards in the 2.x database broke in PAO3. Since I'm
more conservative in this code, I'm just swapping the order, which he
said also fixed his problem.
Reviewed by: mdodd, iwasaki
Submitted by: sanpai@sanpai.org
too many, so I removed the checks for the valid OUIs. We already do a
checksum of the entire ethernet address, so extra checking against the
OUI shouldn't be needed.
Many ed-based Ethernet PC-cards can't get correct MAC address without
this patch.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
Reviewed by: Warner Losh <imp@village.org>
o Expose ed_stop and call it early to shutdown the hardware.
o When releasing the interrupt, pass the cookie for the irq, not
a pointer to the cookie (this is the base problem).
o Release other resources used, just like the ep driver
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
yet, but that should be resolved shortly. Non memory mapped ed
devices should work, but I cannot test this since my only ed card is
memory mapped.
Submitted by: Matt Dodd <mdodd@freebsd.org>
bootup. Somehow my backout of an abortaive attempt at shared
memory autoconfiguration included this line:
sc->mem_shared = 1;
Which is fairly important as it turns out.
Since I performed my pre-commit testing on a different box with a generic
NE2000 I didn't catch this. Pointy hat.
now lives in the respective bus front end files.
- Add various function prototypes to if_edvar.h
- Clean up some debugging code that snuck into if_ed_isa.c
- Turn on the right bits in files.i386
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
const char *. Originally I was going to add casts from const char * to
char * in some of the pci device drivers, but the reality is that the
pci device probes return constant quoted strings.
