CAM_DEBUG_CDB, CAM_DEBUG_PERIPH and CAM_DEBUG_PROBE) by default.
List of these flags can be modified with CAM_DEBUG_COMPILE kernel option.
CAMDEBUG kernel option still enables all possible debug, if not overriden.
Additional 50KB of kernel size is a good price for the ability to debug
problems without rebuilding the kernel. In case where size is important,
debugging can be compiled out by setting CAM_DEBUG_COMPILE option to 0.
Do not brelse() the buffer unconditionally with BIO_ERROR set if
uiomove() failed. The brelse() treats most buffers with BIO_ERROR as
B_INVAL, dropping their content. Instead, if the write request
covered the whole buffer, remember the cached state and brelse() with
BIO_ERROR set only if the buffer was not cached previously.
Update the buffer dirtyoff/dirtyend based on the progress recorded by
uiomove() in passed struct uio, even in the presence of
error. Otherwise, usermode could see changed data in the backed pages,
but later the buffer is destroyed without write-back.
If uiomove() failed for IO_UNIT request, try to truncate the vnode
back to the pre-write state, and rewind the progress in passed uio
accordingly, following the FFS behaviour.
Reviewed by: rmacklem (some time ago)
Tested by: pho
MFC after: 1 month
date: 2010/12/24 20:12:56; author: henning; state: Exp; lines: +3 -3
in pf_src_connlimit, the indices to sk->addr were swapped.
tracked down and diff sent by Robert B Mills <rbmills at sdf.lonestar.org>
thanks, very good work! ok claudio
Impact is that the "flush" keyword didn't work.
Obtained from: OpenBSD
MFC after: 1 week
until transport will do some probe actions (at least soft reset).
Make ATA/SATA SIMs to not report bogus and confusing PROTO_ATA protocol.
Make ATA/SATA transport to fill that gap by reporting protocol to SIM with
XPT_SET_TRAN_SETTINGS and patching XPT_GET_TRAN_SETTINGS results if needed.
SoC variants. Fold the AT91SAM9XE chips into the AT91SAM9260
handling, where appropriate. The following SoCs/SoC families are recognized:
at91cap9, at91rm9200, at91sam9260, at91sam9261, at91sam9263,
at91sam9g10, at91sam9g20, at91sam9g45, at91sam9n12, at91sam9rl,
at91sam9x5
and the following variations are also recognized:
at91rm9200_bga, at91rm9200_pqfp, at91sam9xe, at91sam9g45, at91sam9m10,
at91sam9g46, at91sam9m11, at91sam9g15, at91sam9g25, at91sam9g35,
at91sam9x25, at91sam9x35
This is only the identification routine: no additional Atmel devices
are supported at this time.
# With these changes, I'm able to boot to the point of identification
# on a few different Atmel SoCs that we don't yet support using the
# KB920X config file -- someday tht will be an ATMEL config file...
Put a bandaid to prevent ixgbe(4) from completely locking up the system
under high load. Our platform has a few CPU cores and a single active
ixgbe(4) port with 4 queues. Under high enough traffic load, at about
7.5GBs and 700,000 packets/sec (outbound), the entire system would
deadlock. What we found was that each CPU was in an endless loop on a
different ix taskqueue thread. The OACTIVE flag had gotten set on each
queue, and the ixgbe_handle_queue() function was continuously rescheduling
itself via the taskqueue_enqueue. Since all CPUs were busy with their
taskqueue threads, the ixgbe_local_timer() function couldn't run to clear
the OACTIVE flag.
Submitted by: scottl
MFC after: 1 week
http://austingroupbugs.net/view.php?id=385#c713
(Resolved state) recommend this way for the current standard (called
"earlier" in the text)
"However, earlier versions of this standard did not require this, and the
same example had to be written as:
// buf was obtained by malloc(buflen)
ret = write(fd, buf, buflen);
if (ret < 0) {
int save = errno;
free(buf);
errno = save;
return ret;
}
"
from feedback I have for previous commit it seems that many people prefer
to avoid mass code change needed for current standard compliance
and prefer to track unpublished standard instead, which requires now
that free() itself must save errno, not its usage code.
So, I back out "save errno across free()" part of previous commit,
and will fill PR for changing free() isntead.
2) Remove now unused serrno.
MFC after: 1 week
