So a command like
kill _HUP 1
now fails without sending SIGTERM to init.
The behaviour when kill(2) fails remains unchanged: processing continues.
This matches other implementations and POSIX and is useful for killing
multiple processes at once when some of them may already be gone.
PR: bin/40282
run. This makes the 'ctfconvert' and 'ctfmerge' programs show up during
a build when compiling a kernel, a library or a program.
Sponsored by: The FreeBSD Foundation
PR SCTP FWD-TSN's would not be sent and thus
cause a stalled connection. Also the rwnd
Calculation was also off on the receiver side for
PR-SCTP.
MFC after: 1 month
The emulation of 'ld' and 'sd' instructions only works for ABIs that support
64-bit registers and the instructions 'ldl' and 'ldr' that operate on those
registers.
Reviewed by: jmallett
that with a 32-bit ABI on a system with 64-bit registers can attempt to
access an invalid (well, kernel) memory address rather than the intended
user address for stack-relative loads and stores. Lowering the stack
pointer works around this. [1]
o) Make TRAP_DEBUG code conditional on the trap_debug variable. Make
trap_debug default to 0 instead of 1 now but make it possible to change it
at runtime using sysctl.
o) Kill programs that attempt an unaligned access of a kernel address. Note
that with some ABIs, calling useracc() is not sufficient since the register
may be 64-bit but vm_offset_t is 32-bit so a kernel address could be
truncated to what looks like a valid user address, allowing the user to
crash the kernel.
o) Clean up unaligned access emulation to support unaligned 16-bit and 64-bit
accesses. (For 16-bit accesses it was checking for user access to too much
memory (4 bytes) and there was no 64-bit support.) This still lacks support
for unaligned load-linked and store-conditional.
Reviewed by: [1] gonzo
and exclusion patterns [1]
- Some improvements on the exiting code, like replacing memcpy with
strlcpy/strcpy
Approved by: delphij (mentor)
Pointed out by: bf [1], des [1]
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
avoid a hang in the SSL case if the server sends a close notification
before we are done reading. In the non-SSL case, it can provide a
minor (but probably not noticeable) performance improvement for small
transfers.
MFC after: 3 weeks
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
now it uses a very dumb first-touch allocation policy. This will change in
the future.
- Each architecture indicates the maximum number of supported memory domains
via a new VM_NDOMAIN parameter in <machine/vmparam.h>.
- Each cpu now has a PCPU_GET(domain) member to indicate the memory domain
a CPU belongs to. Domain values are dense and numbered from 0.
- When a platform supports multiple domains, the default freelist
(VM_FREELIST_DEFAULT) is split up into N freelists, one for each domain.
The MD code is required to populate an array of mem_affinity structures.
Each entry in the array defines a range of memory (start and end) and a
domain for the range. Multiple entries may be present for a single
domain. The list is terminated by an entry where all fields are zero.
This array of structures is used to split up phys_avail[] regions that
fall in VM_FREELIST_DEFAULT into per-domain freelists.
- Each memory domain has a separate lookup-array of freelists that is
used when fulfulling a physical memory allocation. Right now the
per-domain freelists are listed in a round-robin order for each domain.
In the future a table such as the ACPI SLIT table may be used to order
the per-domain lookup lists based on the penalty for each memory domain
relative to a specific domain. The lookup lists may be examined via a
new vm.phys.lookup_lists sysctl.
- The first-touch policy is implemented by using PCPU_GET(domain) to
pick a lookup list when allocating memory.
Reviewed by: alc
details of the string buffer allocation in one place.
Eliminate the portion of the string buffer that was dedicated to storing
the interpreter name. The pointer to the interpreter name can simply be
made to point to the appropriate argument string.
Reviewed by: kib
thus don't depend on one_pass flag anymore.
This is a POLA violation, but it is quite difficult to restore
the old behavior with new code. Also, the new behavior matches
behavior of the older "tee" action, and this is more intuitive.
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
either find an existing entry, or allocate a new one. In the latter
case an entry would have flags, that were supplied as argument to
lla_lookup(). In case of an existing entry, flags aren't modified.
This lead to losing LLE_PUB and/or LLE_PROXY flags.
We should apply these flags either in lla_rt_output() or in the
in.c:in_lltable_lookup(). It seems to me that lla_rt_output() is
a more correct choice.
PR: kern/148784, kern/146539
Silence from: qingli, 5 days
booting again.
The code is a copy of the mips/mips/tick.c with minor modifications for
XLR interrupt handling. Disable mips/rmi/clock.c for now, the PIC based
timer code will be added later.
