for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
during a trek through RCS. The Macronix 98713 and 98713A both have the
same PCI device ID but different revision numbers, and we need to be
able to tell one from the other. The 98715 and 98715A chips have the
same device ID as the 98725 chip but different revision numbers, however
we lump them into the same category except when identifying them during
the PCI probe output.
The main reason we need tell the chips apart is that the Macronix app
notes say you have to write a special magic number into one of the
registers in order to put the chip in normal operating mode. The 98713
requires one magic value, while all the others require a different one.
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
alpha, operations involving non-finite numbers or denormalised numbers
or operations which should generate such numbers will cause an arithmetic
exception. For programs which follow some strict code generation rules,
the kernel trap handler can then 'complete' the operation by emulating
the faulting instruction.
To use software completion, a program must be compiled with the arguments
'-mtrap-precision=i' and '-mfp-trap-mode=su' or '-mfp-trap-mode=sui'.
Programs compiled in this way can use non-finite and denormalised numbers
at the expense of slightly less efficient code generation of floating
point instructions. Programs not compiled with these options will receive
a SIGFPE signal when non-finite or denormalised numbers are used or
generated.
Reviewed by: John Polstra <jdp@polstra.com>
option not defined the sysctl int value is set to -1 and read-only.
#ifdef KERNEL's added appropriately to wall off visibility of kernel
routines from user code.
Add ICMP_BANDLIM option and 'net.inet.icmp.icmplim' sysctl. If option
is specified in kernel config, icmplim defaults to 100 pps. Setting it
to 0 will disable the feature. This feature limits ICMP error responses
for packets sent to bad tcp or udp ports, which does a lot to help the
machine handle network D.O.S. attacks.
The kernel will report packet rates that exceed the limit at a rate of
one kernel printf per second. There is one issue in regards to the
'tail end' of an attack... the kernel will not output the last report
until some unrelated and valid icmp error packet is return at some
point after the attack is over. This is a minor reporting issue only.
not like the 6-byte read and write commands! It returns illegal request,
with the field pointer pointing to byte 9 of a 6 byte CDB.
In any case, the work around is to put in a quirk mechanism that makes sure
that we don't send 6-byte reads or writes to this device. It's rather sad
that this is necessary. You'd think that they would be able to get
something that basic to work right in their firmware...
Reviewed by: gibbs
Reported by: Adam McDougall <bsdx@spawnet.com>
problem is worked around by using an interrupt gate for the page
fault handler. This code was originally made for NetBSD/pc98 by
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp> and has already
been in PC98 tree. Because of this bug, trap_fatal cannot show
correct page fault address if %cr2 is obtained in this function.
Therefore, trap_fatal uses the value from trap() function.
- The trap handler always enables interruption when buggy application
or kernel code has disabled interrupts and then trapped. This code
was prepared by Bruce Evans <bde@FreeBSD.org>.
Submitted by: Bruce Evans <bde@FreeBSD.org>
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp>
going to want a major number from that list instead. Also use the
same preallocated local range (500-600) for blkdevs as well as cdevs,
just to be orthogonal. The latter was for Brian, who has a *lot*
of local device drivers and needs more than just a single reserved
number.
can set if your hw/sw produces the "calcru negative..." message.
Setting the alternate method (sysctl -w kern.timecounter.method=1)
makes the the get{nano|micro}*() functions call the real thing at
resulting in a measurable but minor overhead.
I decided to NOT have the "calcru" change the method automatically
because you should be aware of this problem if you have it.
The problems currently seen, related to usleep and a few other corners
are fixed for both methods.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
install all those images at all (nor to install them under /usr/mdec), given
the high degree of customization this Makefile needs in order to get images
that are actually useful for some NIC.
Submitted by: John Hay <jhay@mikom.csir.co.za>,
Paul Allenby <pallenby@mikom.csir.co.za>
