It would have been on an actual named pass before, but none were really
appropriate in name. Move it to the recently created SUPPORTDEV pass, which
perfectly describes it and keeps it in the right order.
Getting regulator is good, enabling them is better.
When the mmc stack decide to change the voltage for IO, don't
change the main vcc of the sd/mmc, only the io vcc.
AXP803 and AXP813/818 are very similar, only two regulators differs.
AXP803 is the companion chip for A64/R18
AXP813 is the companion chip for A83T
AXP818 is the companion chip for H8 (~A83T)
Add support for all regulators found in both of them.
to what other arches (all except riscv and armv4/5) do.
Submitted by: Hyun Hwang <hyun@caffeinated.codes>
Differential Revision: https://reviews.freebsd.org/D14465
(using "boot -d" at the loader propmt or setting boot_ddb in loader.conf).
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D14428
We don't support float in the boot loaders, so don't include
interfaces for float or double in systems headers. In addition, take
the unusual step of spiking double and float to prevent any more
accidental seepage.
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
appears that node names no longer include leading zeroes in the @address
qualifiers, so we have to search for the nodes involved in interrupt fixup
using both flavors of name to be compatible with old and new .dtb files.
(You know you're in a bad place when you're applying a workaround to code
that exists only as a workaround for another problem.)
The FDT variant is called "gicv2m" too, and as both would try to register
on gic, only one of them would succeed, while we want them both in a
GENERIC kernel.
Reviewed by: andrew
significant source of cache line contention from vm_page_alloc(). Use
accessors and vm_page_unwire_noq() so that the mechanism can be easily
changed in the future.
Reviewed by: markj
Discussed with: kib, glebius
Tested by: pho (earlier version)
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14273
Remove most of the Atmel at91 boards. Most of them are no longer
relevant or used by people. Kept ATMEL since it should work on all the
boards that still work (I've not confirmed this, since I don't have
all these boards). Also kept SAM9G20EK, since I have several boards
that it is used on. If I've deleted a kernel in error, please let me
know.
On the OrangePi One at least, emac reset when an ethernet cable is not
plugged in seems to break ethernet. Soft reset will fail, even with
increasing the delay and retries to wait for up to 20 seconds. This can be
reproduced across at least two different OrangePi One's by simply leaving
ethernet cable unplugged when awg attaches. Whether it's plugged in or not
through u-boot process makes no difference.
Skipping the reset in this configuration doesn't seem to cause any problems,
tried across many many reboots with and without ethernet cable plugged in.
Tested on: OrangePi One
Tested on: Other boards (manu)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13974
global to per-domain state. Protect reservations with the free lock
from the domain that they belong to. Refactor to make vm domains more
of a first class object.
Reviewed by: markj, kib, gallatin
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14000
Similarly as we already do for arm64, for mitigation is necessary to
flush branch predictor when we:
- do task switch
- receive prefetch abort on non-userspace address
The user can disable this mitigation by setting 'machdep.disable_bp_hardening'
sysctl variable, or it can check actual system status by reading
'machdep.spectre_v2_safe'
The situation is complicated by fact that:
- for Cortex-A8, the BPIALL instruction is effectively NOP until the IBE bit
in ACTLR is set.
- for Cortex-A15, the BPIALL is always NOP. The branch predictor can be
only flushed by doing ICIALLU with special bit (Enable invalidates of BTB)
set in ACTLR.
Since access to the ACTLR register is locked to secure monitor/firmware on
most boards, they will also need update of firmware / U-boot.
In worst case, when secure monitor is on-chip ROM (e.g. PandaBoard),
the board is unfixable.
MFC after: 2 weeks
Reviewed by: imp, emaste
Differential Revision: https://reviews.freebsd.org/D13931
the "power down" watchdog used by the ROM boot code is still active when the
regular watchdog is activated, turn off the power-down watchdog.
This adds support for the "fsl,ext-reset-output" FDT property. When
present, that property indicates that a chip reset is accomplished by
asserting the WDOG1_B external signal, which is supposed to trigger some
external component such as a PMIC to ready the hardware for reset (for
example, adjusting voltages from idle to full-power levels), and assert the
POR signal to SoC when ready. To guard against misconfiguation leading to a
non-rebootable system, the external reset signal is backstopped by code
that asserts a normal internal chip reset if nothing responds to the
external reset signal within one second.
bottom of the file, where it is in most imx5/6 drivers. Switch from an RD2
macro using bus_space_read_2() to an inline function using bus_read_2();
likewise for WR2. Use RESOURCE_SPEC_END to end the resource_spec list.
Net effect should be no functional changes.
instead of frobbing the registers directly.
As a hack the bcm2835_pwm kmod presently ignores the 'status="disabled"'
in the RPI3 DTB, assuming that if you load the kld you probably
want the PWM to work.
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
functionality on Raspberry Pi 0.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13924
(i386 and arm) that never implement them. This allows the removal of
#ifdef PHYS_TO_DMAP on code otherwise protected by a runtime check on
PMAP_HAS_DMAP. It also fixes the build on ARM and i386 after I forgot an
#ifdef in r328168.
Reported by: Milan Obuch
Pointy hat to: me
kernel by PHYS_TO_DMAP() as previously present on amd64, arm64, riscv, and
powerpc64. This introduces a new MI macro (PMAP_HAS_DMAP) that can be
evaluated at runtime to determine if the architecture has a direct map;
if it does not (or does) unconditionally and PMAP_HAS_DMAP is either 0 or
1, the compiler can remove the conditional logic.
As part of this, implement PHYS_TO_DMAP() on sparc64 and mips64, which had
similar things but spelled differently. 32-bit MIPS has a partial direct-map
that maps poorly to this concept and is unchanged.
Reviewed by: kib
Suggestions from: marius, alc, kib
Runtime tested on: amd64, powerpc64, powerpc, mips64
Focus on code where we are doing multiplications within malloc(9). None of
these ire likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
X-Differential revision: https://reviews.freebsd.org/D13837
- Add a per compatible configuration struct
- Not all SoC uses the same size for DMA transfert, add this into the
configuration data
- Use new timing mode for some SoC (A64 mmc)
- Auto calibrate clock for A64 mmc/emmc
- A64 mmc controller need masking of data0
- Add support for vmmc/vqmmc regulator
- Add more capabilities, r/w speed is better for eMMC
- MMC_CAP_SIGNALING_180 gives weird result so do not enable it for now.
- Add new register documented in H3/A64 user manual
Tested-On: Pine64-LTS (A64), eMMC still doesn't work
Tested-On: A64-Olinuxino (A64), sd and eMMC are working
Tested-On: NanoPi Neo Plus2 (H5), sd and eMMC are working
Tested-On: OrangePi PC2 (H5), sd only (no eMMC)
Tested-On: OrangePi One (H3), sd only (no eMMC)
Tested-On: BananaPi M2 (A31s), sd only (no eMMC)