- These were needed on armv4/5 (VIVT cache), not needed on armv6.
- The wbinv_all call can't be used on SMP systems; cache operations by
set/way are not broadcast to other cores.
- The TLB maintenance operations needed for pmap_growkernel() happen in
pmap_grow_l2_bucket(), so there's no need to flush all TLB entries at
the end.
- There may not be any need for the TLB flush at the beginning of
pmap_release(), but it's left in for now pending more investigation.
Pointed out by: Svatopluk Kraus <onwahe@gmail.com>
Discussed with: cognet@
While it is the recommended initialization procedure, it hangs on the reset
of the second GPIO module on pandaboard.
Removes the module reset for now as more investigation would be needed.
Reported by: jceel
These should have been part of r264129, they are part of the overall set
of changes that got several weeks of testing. I must have fumbled them
while merging various patchsets.
On AM335x each one of the four GPIO banks has two physical interrupt
lines, so we now allocate resources and setup our interrupt handler for
all the (8) available interrupts.
On OMAP3 and OMAP4 there is only one interrupt for each GPIO bank (6
banks, 6 interrupts), but there are two set of registers where the
first one is used to setup the delivery of interrupts to the MPU and
the second set, setup the delivery of interrupts to the DSP.
On AM335x, each set of registers controls each one of the interrupt
lines.
- Remove nonexistent registers for OMAP4 and AM335x, replace their use with
the correct ones for these SoCs.
- Remove stray whitespace.
Based on OMAP3, OMAP4 and AM335x TRMs.
Tested on Beaglebone-black.
enabled. Also switch IMX6 to use SCHED_ULE.
The now-unreferenced WANDBOARD.common config will be deleted after giving
folks who may be including it a heads-up to switch to IMX6.
- Add cpu_cpwait to comply with the convention.
- Add missing TLB invalidations, especially in pmap_kenter & pmap_kremove
with distinguishing between D and ID pages.
- Modify pmap init/bootstrap invalidations to ID, just to be safe.
- Fix TLB-inv and PTE_SYNC ordering.
This combines changes submitted by ian@, cognet@, and Wojciech Macek,
which have all been tested together as a unit.
Perform sychronization (by "isb" barrier) after TTB is set. This
is done to ensure that TLB invalidation always executes after
TTB modification and operates on valid CP15 data (per specification).
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian@, cognet@
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
errors.
Reset the GPIO module during the initialization. This is guaranteed to be
the same as a hardware reset. Tested on AM335x (BBB) and checked against
the omap3 and omap4 TRM.
Do a better job freeing resources when there are errors and on
ti_gpio_detach().
We don't know our ARM security state, so one of them will operate.
- Don't set frequency, since it's unpossible in non-secure state.
Only rely on DTS clock-frequency value or get clock from timer.
Discussed with: ian, cognet
This adds the concept of "operating points," combinations of frequency
and voltage at which the cpu is known to work correctly. Some day these
should come from FDT data, but for now the table is hard-coded.
This also allows tuning the min and max operating frequencies. The min
frequency is what the thermal management code will slow down to if the
core temperature gets too high. The max frequency is what gets used if
the temperature is okay.
Normally the max cannot be set higher than the value burned into the
ocotp fuses as the chip's rated max, but there is now a new sysctl+tunable
cpu_overclock_enable; when set to non-zero it allows raising the frequency
above the ocotp value: USE WITH CARE! (At least one of my imx6 boards
has a cpu whose ocotp values never got set correctly; they claim a max
of 792mhz, but the physical markings on the chip say it's good to 1ghz.)
Because all these values affect the entire SoC, there is a new sysctl
node, hw.imx6, where all these values live. The values that are currently
under dev.imx6_anatop.0 should probably move to hw.imx6 too, because
"anatop" doesn't even mean anything to me, let alone to an end user.
description was eaten by the dog (or an editor crash or something).
Add variable-frequency support to the arm mpcore eventtimer driver.
This allows a platform's early init code to tell the mpcore driver that the
clock frequency can vary. That causes the mpcore driver to register an
eventtimer, but not a timecounter. The platform has to provide a time
counter using some other fixed-frequency clock, but can still use the
per-cpu goodness of the mpcore hardware for event timers.
When the platform support code does something to change the frequency of
the CPU clocks (power saving, thermal management) it must tell the mpcore
driver code about it using arm_tmr_change_frequency().
register values, then restart the timer. This prevents a situation where
an old event fires just as we're about to load a new value into the timer,
when the start routine is called to change the time of the current event.
Also re-nest the parens properly for casting the result of converting
time and frequency to a count. This doesn't actually change the result of
the calcs, but will some day prevent a loss-of-precision warning on the
assignment, if that warning gets enabled.
Support covers device drivers for:
- Interrupt Combiner
- gpio/pad, External Interrupts Controller (pad)
- I2C Interface
- Chrome Embedded Controller
- Chrome Keyboard
Also:
- Use new gpio dev class in EHCI driver
- Expand device tree information
* Save the required VFP registers on context switch. If the exception bit
is set we need to save and restore the FPINST register, and if the fp2v
bit is also set we need to save and restore FPINST2.
* Move saving and restoring the floating point control registers to C.
* Clear the fpexc exception and fp2v flags on a floating-point exception.
* Signal a SIGFPE if the fpexc exception flag is set on an undefined
instruction. This is how the ARM core signals to software there is a
floating-point exception.
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
