It turned out that devmap.c is not only file in which PTE_DEVICE
is used and simultaneously, built for both armv4 and armv6 platforms.
When I tried to build all arm kernels before r295168 commit, it was
hid by some other local changes in my tree. I hope that this is just
temporary workaround before VM_MEMATTR_DEVICE could be used instead of
PTE_DEVICE outside of pmap code for __ARM_ARCH < 6.
instead of hiding behind pmap_map_chunk(). It's not longer needed
after old pmap-v6 code was removed.
For compatibility with __ARM_ARCH < 6, define PTE_DEVICE in devmap.c
file. Certainly, it would be nice if VM_MEMATTR_DEVICE could be used
even for __ARM_ARCH < 6.
do not depend on pmap internals. This is a preparation for hiding
internal pmap definitions as much as possible from the rest of system.
Simultaneously, the protection argument evaluation is fixed. Happily,
it did not effect the mappings. And it's the reason why it was not fixed
earlier.
Use per-CPU structure to store HW watchpoints registers state
for each CPU present in the system. Those registers will be restored
upon wake up from the STOP state if requested by the debug_monitor
code. The method is similar to the one introduced to AMD64.
We store all possible 16 registers for HW watchpoints
(maximum allowed by the architecture).
HW breakpoints are not maintained since they are used for single
stepping only.
Pointed out by: kib
Reviewed by: wma
No strong objections from: kib
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4338
This allows, for example, UEFI pass a memory map with some ram in this
region, but for us to ignore it. This is the case when running under the
qemu virt machine type.
Sponsored by: ABT Systems Ltd
Allows for using hardware watchpoints for 1, 2, 4, 8 byte long addresses.
The default configuration of watchpoint is RW but code allows to select
RO or WO and X.
Since debugging registers are per-CPU (CP14) the watchpoint is set on
the CPU that was lucky (or not) to enter DDB.
HW breakpoints are used to perform single step in KDB.
When HW breakpoint is enabled all watchpoints are temporary disabled
to avoid recursive abort on both watchpoint and breakpoint.
In case of branch, the breakpoint is set to both - next instruction
and possible branch address. This requires at least 2 breakpoints
supported in the CPU however this is a must for ARMv6/v7 CPUs.
Reviewed by: imp
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4037
pmap implementations on ARM. This way minidump code can be used without
any platform specific modification.
Also, this is the last piece missing for ARM_NEW_PMAP.
Differential Revision: https://reviews.freebsd.org/D5023
into a new function that other platforms can share.
This creates a new ofw_reg_to_paddr() function (in a new ofw_subr.c file)
that contains most of the existing ppc implementation, mostly unchanged.
The ppc code now calls the new MI code from the MD code, then creates a
ppc-specific bus_space mapping from the results. The new arm implementation
does the same in an arm-specific way.
This also moves the declaration of OF_decode_addr() from ofw_machdep.h to
openfirm.h, except on sparc64 which uses a different function signature.
This will help all FDT platforms to set up early console access using
OF_decode_addr().
The ci20 port (by kan@) is going to reuse almost all of the intrng code
since the SoC in question looks suspiciously like someone took an ARM
SoC design and replaced the ARM core with a MIPS core.
* migrate out the code;
* rename ARM_ -> INTR_;
* rename arm_ -> intr_;
* move the interrupt flush routine from intr.c / intrng.c into
arm/machdep_intr.c - removing the code duplication and removing
the ARM specific bits from here.
Thanks to the Star Wars: The Force Awakens premiere line for allowing
me a couple hours of quiet time to finish the universe builds.
Tested:
* make universe
TODO:
* The structure definitions in subr_intr.c still includes machine/intr.h
which requires one duplicates all of the intrng definitions in
the platform code (which kan has done, and I think we don't have to.)
Instead I should break out the generic things (function declarations,
common intr structures, etc) into a separate header.
* Kan has requested I make the PIC based IPI stuff optional.
(1) The pmap argument passed to the function must be current pmap only.
(2) The process must be single threaded as the function is called either
when a process is exiting or from exec_new_vmspace().
Remove pmap_tlb_flush_ng() which is not used anywhere now.
Approved by: kib (mentor)
clock_gettime(2) on ARMv7 and ARMv8 systems which have architectural
generic timer hardware. It is similar how the RDTSC timer is used in
userspace on x86.
Fix a permission problem where generic timer access from EL0 (or
userspace on v7) was not properly initialized on APs.
For ARMv7, mark the stack non-executable. The shared page is added for
all arms (including ARMv8 64bit), and the signal trampoline code is
moved to the page.
Reviewed by: andrew
Discussed with: emaste, mmel
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D4209
Boundary Trace to assembly to reduce the overhead of these checks.
Submitted by: Howard Su <howard0su@gmail.com>
Relnotes: Yes
Differential Revision: https://reviews.freebsd.org/D4266
- add new TEX class for WT cacheable memory
- export new TEX class to kernel as VM_MEMATTR_WT attribute
- add new aliases VM_MEMATTR_WRITE_COMBINING and
VM_MEMATTR_WRITE_BACK, it's used in DRM code
Note:
Only Cortex A8 supports WT caching in HW. On rest of Cortex CPUs,
WT requests is treated as uncacheable.
Approved by: kib (mentor)
Replace tlb_flush_local() by tlb_flush() as even not global mappings
could be fetched to TLB(s) on other cores by speculative table walk.
From OS point of view, it was not a problem as either such mappings
were not used anymore or they were flushed from TLB(s) when reused.
However, from hardware point of view, it was a problem. Not flushed
mappings could be a target for speculative reads or prefetches (which
might be quite aggresive on ARM cores). As speculative read can fill
cacheline, it can cause a real problem, when physical page is reused,
but mapped with different memory attributes.
Anyhow, it's good to have only valid mappings in TLB(s).
Approved by: kib (mentor)
This structure must be binary compatible regardless of PMAP
version being used. Create reserved section for NEW_PMAP to
make other variables be placed exactly in the same memory
addresses. This fixes kgdb/gdb behavoiur, which uses pcb.h stuctures.
The NEW_PMAP is kernel flag, so it does not propagate to the buildworld,
what makes the tools using pcb.h unable to parse PCB data.
Reviewed by: mmel, kib
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4011
Allow manipulation with PSR_A bit on ARMv6+.
Remove declaration of unused functions.
This effectively enables asynchronous aborts on early bootstrap stage,
which previously was not enabled due to an error in enable_interrupts().
PR: 201434
Reported by: Gregory Soutade <soutade at gmail.com>
Approved by: kib (mentor)
function which checks an address for privileged (PL1) write access.
The function is inlined so it does not bring any cost, but makes
function set for checking privileged access complete.
Approved by: kib (mentor)
little-endian configuration for 64-bit variant is supported.
Reviewed by: mmel
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D4113
as of r288992 use it to manage the CCNT.
Use the CNNT for get_cyclecount() instead of binuptime() when device pmu
is compiled in; if it fails to attach, fall back to the former method.
Enable by default for the BeagleBoneBlack configuration.
Optained from: Cambridge/L41
Sponsored by: DARPA/AFRL
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3837
In the old days, device drivers passed NULL for the parent tag when creating
a new tag, and on arm platforms that resulted in a global tag representing
overall platform constraints being substituted in the busdma code. Now all
drivers use bus_get_dma_tag() and if there is a need to represent overall
platform constraints they will be inherited from a tag supplied by nexus or
some bus driver in the hierarchy.
The only arm platforms still relying on the old global-tag scheme were some
xscale boards with special PCI-bus constraints. This change provides those
constraints through a tag supplied by the xscale PCI bus driver, and
eliminates the few remaining references to the old global var.
Reviewed by: cognet
Previous code supported only "continuous" code without any kind of
branch instructions. To change that, new function was implemented
which parses current instruction and returns an addres where
the jump might happen (alternative addr).
mdthread structure was extended to support two breakpoints
(one directly below current instruction and the second placed
at the alternative location).
One of them must trigger regardless the instruction has or has not been
executed due to condition field.
Upon cleanup, both software breakpoints are removed.
This implementation parses only the most common instructions
that are present in the code (like 99.99% of all), but there
is a chance there are some left, not covered by the parsing routine.
Parsing is done only for 32-bit instruction, no Thumb nor Thumb-2
support is provided.
Reviewed by: kib
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Juniper Networks Inc.
Differential Revision: https://reviews.freebsd.org/D4021