active scan is completed just as WI_RID_READ_APS.
This fixes wicontrol -L for ath(4) and awi(4) to have results even if
the driver cannot associate any APs.
o #ifdef _KERNEL the fallback definition for DLT_IEEE802_11_RADIO
o fix many comments
o rename antenna stuff and fix units/reference signal
o change IEEE80211_RADIOTAP_DBM_TX_POWER from unsigned 16-bit value
to a signed 8-bit value
o change IEEE80211_RADIOTAP_FLAGS from 16 bits to 8 bits to simplify
padding requirements
o drop IEEE80211_RADIOTAP_TIME
o change IEEE80211_RADIOTAP_ANTENNA from 16 bits to 8 bits
o drop IEEE80211_RADIOTAP_PAD
o add channel flag definitions for outside the kernel so radiotap
doesn't depend on stuff in ieee80211*.h
Obtained from: NetBSD
o reject scan requests for a device that isn't marked up
This fixes a problem where requesting a scan before marking the device
up would cause a panic because the current channel was set to "any" (0xffff).
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
node lock while sending a management frame as this will potentially
result in a LOR with a driver lock. This doesn't happen for the
Atheros driver but does for the wi driver. Use a generation number
to help process each node once when scanning the node table and
drop the node lock if we need to timeout a node and send a frame.
AP has basic rates that we do not support then ignore them instead
of marking the rate set in error.
This fixes an 11b station associating with an 11g/b AP.
things than record a single value.
o add a per-node method for returning the "current RSSI" for a node
o create a default method that returns ni_rssi which is the rssi for
the last received frame
o use the per-node "get rssi" method to return data for the RID's
submitted by wicontrol, et. al.
Loosely based on work by Tom Marshall <tommy@home.tig-grr.com> for MADWIFI.
In particular, let drivers send up control frames so we can dispatch
them to bpf in monitor mode.
This is the first (small) step to adding more functionality such as
power save mode.
capabilities for outbound management frames. But beware of sending
this when operating on 5GHz channels; some 11a AP's reject association
requests if this bit is set in the capabilities listed.
Obtained from: MADWIFI (with modifications)
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
to override the method pointers for manipulating nodes; this fixes
a problem where the ic_bss node was not being created properly
for the ath driver causing the driver to scribble on random memory.
Noticed by: David Young <dyoung@pobox.com>
rate set element id from an AP. This allows stations to associate with
AP's that violate the 802.11 spec by sending >8 rates. This corrects a
recent regression; older code did likewise.
override in their sub-class; this eliminates the hack of interpreting the
EINPROGRESS return value to mean "don't do any of the normal work"
o correct active scanning so the first channel is only scanned once and so
per-channel passive mode is properly honored
o expose 802.11 FSM state names so every driver doesn't keep a private copy
o eliminate node parameter to ieee80211_begin_scan; it was not being used
o code reorg (relative to old netbsd-derived code) for future growth
o drivers now specify available channels and rates and 802.11 layer handles
almost all ifmedia actions
o multi-mode support for 11a/b/g devices
o 11g protocol additions (incomplete)
o new element id additions (for other than 11g)
o node/station table redone for proper locking and to eliminate driver
incestuousness
o split device flags and capabilities to reduce confusion and provide room
for expansion
o incomplete power management infrastructure (need to revisit)
o incomplete hooks for software retry
o more...
