the value written to MSR register was always 0 regardless of value passed
by user.
- Use proper data pointer when performing AMD microcode update. Previously,
the pointer to user-space data has been provided instead, which is totally
incorrect.
Approved by: re (kib)
MFC after: 1 week
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
for the pmclog.
Reported by: Ryan Stone <rstone at sandvine dot com>
Tested by: Ryan Stone <rstone at sandvine dot com>
Sponsored by: Sandvine Incorporated
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
The Intel 2d driver calls modeset before reinstalling the handler on
a vt switch. This means that vblank status ends up getting cleared
after it has been setup. Restore saved values for the pipestat registers
rather than just wiping them out.
MFC after: 3 days
Use the vbl_lock when maniputlating the refcount. Eventually I want to
convert this to use our internal refcount code. Continue to use atomic
ops for manipulating vblank count since we access it often just for
reading.
MFC after: 3 days
- build ifmedia list based on phy->caps, not string comparisons.
- rebuild media list when a transceiver change is detected.
- return EOPNOTSUPP instead of ENXIO in cxgb_media_status.
Approved by: gnn (mentor)
MFC after: 2 weeks.
I tried re-ordering ether_ifdetach(), but this created a new race
where sometimes, when under heavy receive load (>1Mpps) and running
tcpdump, the machine would panic. At panic, the ithread was still in
the original (not dead) if_input() path, and was accessing stale BPF
data structs. By using a dying flag, I can close the interface prior
to if_detach() to be certain the interface cannot send packets up in
the middle of ether_ifdetach.
handling in order to reduce interrupt overhead which results in
better performance.
- Call ether_ifdetach(9) before stopping the controller and the
callouts detach in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- Add explicit IFF_DRV_RUNNING checking in order to prevent extra
link up/down events when using dhclient(8).
- Use the correct macro for deciding whether 2/3 of the available TX
descriptors are used.
- Wrap the RX fault printing in #ifdef CAS_DEBUG in order to not
unnecessarily frighten users and as debugging was the actual
intention. Real errors caused by these faults still will be
accumulated as input errors. It might be a good idea to later on
add driver specific counters for the faults though.
Submitted by: yongari (original patch)
longer useful for the FD_STYPE and FD_SOPTS ioctls to insist on being
issued on a writable file descriptor. Otherwise, there's no longer a
chance to set the drive type or options when a read-only medium is
present in the drive, as there is no way to obtain a writable fd then.
call ether_ifdetach(9) before stopping the controller and the
callouts. The consensus is that the latter is now safe to do and
should also solve the problem of active BPF listeners clearing
promiscuous mode can result in the tick callout being restarted
which in turn will trigger a panic once it's actually gone.
- honor parent DMA tag limitations, as man page requires,
- allow data buffer to be allocated within full 64bit address range, when
support is announced by hardware,
- add quirk, disabling 64bit addresses for broken chips, use it for MCP78.
This removes unnecessary PCI #includes dependency for systems with ATA
controllers living at non-PCI buses.
Submitted by: Piotr Ziecik
Obtained from: Semihalf
rlimit RLIMIT_SWAP that limits the amount of swap that may be reserved
for the uid.
The accounting information (charge) is associated with either map entry,
or vm object backing the entry, assuming the object is the first one
in the shadow chain and entry does not require COW. Charge is moved
from entry to object on allocation of the object, e.g. during the mmap,
assuming the object is allocated, or on the first page fault on the
entry. It moves back to the entry on forks due to COW setup.
The per-entry granularity of accounting makes the charge process fair
for processes that change uid during lifetime, and decrements charge
for proper uid when region is unmapped.
The interface of vm_pager_allocate(9) is extended by adding struct ucred *,
that is used to charge appropriate uid when allocation if performed by
kernel, e.g. md(4).
Several syscalls, among them is fork(2), may now return ENOMEM when
global or per-uid limits are enforced.
In collaboration with: pho
Reviewed by: alc
Approved by: re (kensmith)
the PHYs as some PHY drivers use it (but probably shouldn't). How
gem(4) has worked with brgphy(4) on powerpc without this so far is
unclear to me.
- Introduce a dying flag which is set during detach and checked in
gem_ioctl() in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- In gem_stop() reset rather than just disable the transmitter and
receiver in order to ensure we're not unloading DMA maps still in
use by the hardware. [1]
- The blanking time is specified in PCI clocks so we should use twice
the value when operating at 66MHz.
- Spell some 2 as ETHER_ALIGN and a 19 as GEM_STATUS_TX_COMPLETION_SHFT
to make the actual intentions clear.
- As we don't unload the peak attempts counter ignore its overflow
interrupts.
- Remove a stale setting of a variable to GEM_TD_INTERRUPT_ME which
isn't used afterwards.
- For optimum performance increment the TX kick register in multiples
of 4 if possible as suggested by the documentation.
- Partially revert r164931; drivers should only clear the watchdog
timer if all outstanding TX descriptors are done.
- Fix some debugging strings.
- Add a missing BUS_DMASYNC_POSTWRITE in gem_rint().
- As the error paths in the interrupt handler are generally unlikely
predict them as false.
- Add support for the SBus version of the GEM controller. [2]
- Add some lock assertions.
- Improve some comments.
- Fix some more or less cosmetic issues in the code of the PCI front-end.
- Change some softc members to be unsigned where more appropriate and
remove unused ones.
Approved by: re (kib)
Obtained from: NetBSD (partially) [2], OpenBSD [1]
MFC after: 2 weeks
- Support for 10G-PCIE*-8B*-C (dual-port CX4) NICs
- For dual-port NICs, f/w failover is now a few microsecs
instead of a few millisecs.
- On failover, f/w sends RARP broadcast to make the change
immediately known to the network
- Fixed a bug observed on IBM X3 architecture where
some spurious ecrc errors would be reported when OS enabled
ecrc support.
Sponsored by: Myricom Inc.
