from fiddling with CS_TTGO since fiddling with CS_TTGO was removed in
rev.1.218 of the i386/isa version (which was merged with loss of history
in rev.1.223 of this version).
- Removed conversion of a zero input speed to the output speed. This
has been done better in ttioctl() since rev.1.108 of kern/tty.c
almost 5 years ago. comparam() did the conversion incompletely for
the case where the output speed is also zero. It had complications
to avoid using zero speeds, but would still have used a zero input
speed for setting watermarks if kern/tty.c had passed one.
- Never permit the input speed to be different from the output speed.
There was no validity check on the input speed for the case of a zero
output speed. Then we didn't change the physical speeds, but we used
the unvalidated input speed for setting watermarks and didn't return
an error, so ttioctl() stored the unvalidated input speed in the tty
struct where it could cause problems later.
- Removed complications that were to avoid using a divisor of 0. The
divisor is now always valid if the speed is accepted.
in the loopback test in the probe. The delay was too short for consoles
at speeds lower than about 3200 bps. This shouldn't have caused many
problems, since such low speeds are rare and the probe is forced to
succeed for consoles.
COM_NOFIFO() and COM_ESP cases are supposed to be a subsets of the
plain 16550A case, but 16650-related changes made the former fall into
the latter and then both fall into general code for printing the tx
fifo size. This mainly caused hard to parse boot messages like:
"sio0: type 16550A fifo disabled lookalike with 1 bytes FIFO".
COM_NOFIFO() on an ESP port gave a larger mess whose extent is not
clear.
Fixed some nearby style bugs.
defined values instead of hard-coded values. Don't repeat the register
access part of the code 4 times times or triple-space statements. This
fixes half of the style bugs in rev.1.172.
Hardware flow control of 16650As is still officially unsupported. I
was mistaken about it being broken. It is broken in 16650s but is
fixed in 16650As except for the maximum trigger level (which is no
longer used). Testing of the 16650's broken hardware flow control
watermarks by programming them on 16950s showed that their effects are
not too bad if the fifo size and trigger level are reasonably large
(16 is much better than 8).
to ns16550.h. The organization of these files was sort of backwards.
The bits in the registers have no driver or bus dependencies but they
but the offsets of the registers in bus space are very bus-dependent.
However, it does no harm to keep the definitions of the register offsets
in ns16550.h provided they are thought of as internal ns*50 offsets.
was added to the fast path to support the COM_IIR_RXRDYBUG() case even
when that case is not configured. This increased the relative overhead
of sio input by almost 25% in the worst case and by 2-3% in the usual
case (usually only about 0.2% absolute per port at 115200 bps). The
quick fix is to significantly pessimize only the COM_IIR_RXRDYBUG()
case.
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
now unnecessary hack from the previous commit;
- Add support for Interrupt Latch Register (ILR) into puc(4). So far only
ILRs compatible with specifications from Digi International are supported.
Support for other types of ILRs could be easily added later;
- Correct clock frequency for IC Book Labs Dreadnought x16 Lite board;
- Enable ILR detection/usage for IC Book Labs Dreadnought x16 boards.
Sponsored by: IC Book Labs
MFC after: 2 weeks
this card is based on 16750 UART, modify sio(4) a bit to ignore 16750-specific
7th bit of MCR when probing card. This allows card to be detected and attached
as 16550A-compatible device. More work needs to be done in order to enable
nice 16750-specific features such as larger fifo buffer and higher speeds.
Sponsored by: IC Book Labs
MFC after: 2 weeks
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
dev_t to the method functions.
The dev_t can still be found at struct consdev *->cn_dev.
Add a void *cn_arg element to struct consdev which the drivers can use
for retrieving their softc.
Wearing said pointy hat, correct the oversight and hope nobody
notices.
# this should make xircom modems happier to detach once other bugs with
# the cardbus layer are fixed.
Noticed by: scottl
Conical Hat to: imp
identify themselves as serial cards that it would be desirable to
attach a different driver than sio to. Since we are claiming all
serial cards, this is not possible. Instead, return -100 to indicate
that we're willing to take the card, but still allow other drivers to
attach.
Pointed out by: Maksim Yevmenkin
The advanced stage of computer assisted hardware design and
verification is aptly illustrated by the fact that this is necessary
because only the first ports in a single-chip, dual-port async
PC-Card product lacks this register.
