Document the options available for the ata driver.
Disconnect the atapi devices from the old wd driver to avoid conflicts
(they will go away at some point anyways)
* GC unused options
* Move options that exist on all architectures to conf/options
* Add missing options to LINT
* Sort undocumented options list in LINT
Reviewed by: green
to config(8) for static device tables that have not existed for quite
some time. They have been aliases for 'device' for a while, and "tape"
went away entirely as it wasn't used anywhere (except in an example
in LINT.. "fixed").
o Gut the compatibility interface, you now must attach with newbus.
o Unit numbers from pccardd are now ignored. This may change the units
assigned to a card. It now uses the first available unit.
o kill old skeleton code that is now obsolete.
o Use newbus attachment code.
o cleanup interfile dependencies some.
o kill list of devices per slot. we use the device tree for what we need.
o Remove now obsolete code.
o The ep driver (and maybe ed) may need some config file tweaks to
allow it to attach. See config files that were committed for examples
on how to do this.
Drivers to be commited shortly.
This is an interrum fix until the new pccard. ed, ep and sio will be
supported by me with this release, although others are welcome to try
to support other devices before new pccard is working.
I plan on doing minimal further work on this code base. Be careful
when upgrading, since this code is known to work on my laptop and
those of a couple others as well, but your milage may vary.
BUGS TO BE FIXED:
o system memory isn't allocated yet, it will be soon.
o No devices actually have a pccard newbus attach in the tree.
BUGS THAT MIGHT BE FIXED:
o card removal, including suspend, usually hangs the system.
Many thanks to Peter Wemm and Doug Rabson for helping me to fill in
the missing bits of New Bus understanding at FreeBSD Con '99.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
floating before). Attach pccard devices to pcic, one per slot
(although this may change to one per pcic). pcic is now attached to
isa (to act as a bridge) and pccard is attached to pcic, cbb and
pc98ic (the last two are card bus bridge and the pc98ic version of
pcic, neither of which are in the tree yet). Move pccard compat code
into pccard/pccard_compat.c.
THIS REQUIRES A CONFIG FILE CHANGE. You must change your pcic/card
entries to be:
# PCCARD (PCMCIA) support
controller pcic0 at isa?
controller pcic1 at isa?
controller card0
The old system was upside down and this corrects that problem. It
will make it easier to add support for YENTA pccard/card bus bridges.
Much more cleanup needs to happen before newbus devices can have
pccard attachments. My previous commit's comments were premature.
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
be set by a kernel conf option due to the struct buf structural
dependancy (sizing of b_pages[]) creating a conflict with modules
(which are not compiled with kernel config options overrides).
We'll be able to sysctl these two later on when the buffer subsystem
is revamped.
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
UMAPFS_DIAGNOSTIC and UNION_DIAGNOSTIC. Uncommented NULLFS_DIAGNOSTIC.
It is as bogus as the above three but since it is already a new-style
option it is easier to use it than to fix it.
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
