Some hardware like DMA and GPIO controllers might require
more then 8 interrupts per device instance.
Submitted by: Daisuke Aoyama <aoyama at peach.ne.jp>
Discussed with: gber@, raj@
unmerged BERI DTS files) to head:
Use the OFW compatible string "mips,mips4k" rather than
"mips4k,cp0" for interrupt control using MIPS4k CP0.
Suggested by: thompsa
Implement a MIPS FDT PIC decode routine to use when no PIC has been
configured, which assumes a cascade back to the nexus bus (e.g.,
the on-board CP0 interrupt management parts on the MIPS). If the
soc bus in a MIPS DTS file is declared as "mips4k,cp0"-compatible,
then this will be enabled. This is sufficient to allow IRQs to be
configured on BERI.
Sponsored by: DARPA, AFRL
perhaps due to an interrupt configuration problem, do not try to free
device ivars that have not yet have been allocated.
MFC after: 1 week
Reviewed by: gonzo
Sponsored by: DARPA, AFRL
It returns memory regions restricted from being used by kernel. These
regions are dfined in "memreserve" property of root node in the same
format as "reg" property of /memory node
r233822:
Remove useless and wrong piece of code in fdt_get_range() which i
overwrites passed phandle_t node. Modify debug printf in fdt_reg_to_rl()
to be consistent (that is, print start and end *virtual* addresses).
r230560:
Handle "ranges;"
Make fdt_reg_to_rl() responsible for mapping the device memory, instead
on just hoping that there's only one simplebus, and using fdt_immr_va as
the base VA.
r230315
Add a function to get the PA from range, instead of (ab)using
fdt_immr_pa, and use it for the UART driver
of interrupts of direct children. Have the bus_config_intr and
bus_teardown_intr methods implemented by bus_generic_config_intr and
bus_generic_teardown_intr (resp) as we don't need to do anything
special outselves.
This removes all the ``#ifdef $arch'' code that was there because powerpc
didn't have a proper nexus and people tend to copy and paste stuff.
into partitions.
Partitions are created based on data in dts file which are
extracted and interpreted by slicer.
Obtained from: Semihalf
Supported by: FreeBSD Foundation, Juniper Networks
This lets specify whereabouts of the parent PHY for a given MAC node
(and get rid of ugly kludges in mge(4) and tsec(4)).
Obtained from: Semihalf
MFC after: 1 week
According to the open firmware standard, finddevice call has to return
a phandle with value of -1 in case of error.
This commit is to:
- Fix the FDT implementation of this interface (ofw_fdt_finddevice) to
return (phandle_t)-1 in case of error, instead of 0 as it does now.
- Fix up the callers of OF_finddevice() to compare the return value with
-1 instead of 0 to check for errors.
- Since phandle_t is unsigned, the return value of OF_finddevice should
be checked with '== -1' rather than '<= 0' or '> 0', fix up these cases
as well.
Reported by: nwhitehorn
Reviewed by: raj
Approved by: raj, nwhitehorn
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
that represents the host controller. This makes the FDT PCI support
working an a bare-bones manner. This needs a lot more work, of which
the beginning are at the end of the file, compiled-out with #if 0.
The intend being that both the Marvell PCIE and Freescale PCI/PCIX/PCIE
duplicate the same platform-independent domain initialization, that
should be moved into an unified implementation in the FDT code. Handling
of resources requires help from the platform. A unified implementation
allows us to properly support PCI devices listed in the device tree and
configured according to the device tree specification.
Sponsored by: Juniper Networks
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
o fdtbus(4) - the main abstract bus driver for all FDT-compliant systems. This
is a direct replacement for the many incompatible bus drivers grouping
integrated peripherals on embedded platforms (like obio(4), ocpbus(4) etc.)
o simplebus(4) - bus driver representing ePAPR style 'simple-bus' node, which
is an umbrella device for most of the integrated peripherals on a typical
system-on-chip device.
o Other components (common routines library, PCI node processing helper
functions)
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
