this fixes geom_redboot on boards that have multiple parts/regions as it
uses the value to locate the FIS directory which is in the last erase
region of flash
Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can be observed via sysctl.
Two new cxgbtool commands to get uP logic analyzer info and uP IOQs
Synced up with Chelsio's "common code" (as of 03/03/09)
Submitted by: Navdeep Parhar at Chelsio
Reviewed by: gnn
MFC after: 2 weeks
the PORTEN and MEMEN bits in the command register than to zero the
bars.
Use pci_write_ivar directly instead of a one-line wrapper that adds no
value.
Track verbosity changes in pci.
Remove a stray blank line.
After I imported libteken into the source tree, I noticed syscons didn't
store the cursor position inside the terminal emulator, but inside the
virtual terminal stat. This is not very useful, because when you
implement more complex forms of line wrapping, you need to keep track of
more state than just the cursor position.
Because the kernel messages didn't share the same terminal emulator as
ttyv0, this caused a lot of strange things, like kernel messages being
misplaced and a missing notification to resize the terminal emulator for
kernel messages never to be resized when using vidcontrol.
This patch just removes kernel_console_ts and adds a special parameter
to te_puts to determine whether messages should be printed using regular
colors or the ones for kernel messages.
Reported by: ache
Tested by: nyan, garga (older version)
We should just leave the underlying TTY objects alone when scrolling
around in KDB. It should be handled by Syscons exclusively.
Reported by: pluknet gmail com
get default next page configuration. While I'm here explicitly set
IP1000PHY_ANAR_CSMA bit. This bit is read-only and always set
by hardware so setting it has no effect but it would clear the
intention. With this change controllers that couldn't establish
1000baseT link should work.
PR: kern/130846
mapping. The tunable is OFF for all controllers except RTL8169SC
family. RTL8169SC seems to require more magic to use memory
register mapping. r187483 added a fix for RTL8169SCe controller but
it does not looke like fix other variants of RTL8169SC.
Tested by: Gavin Stone-Tolcher g.stone-tolcher <> its dot uq dot edu dot au
o correct dBm<->mW conversion logic
o set net80211 TXPMGT capability only if driver reports it is capable
PR: kern/132342
Submitted by: "Paul B. Mahol" <onemda@gmail.com>
Fix bugs and improve HID parsing.
- fix possible memory leak found
- fix possible NULL pointer access
- fix possible invalid memory read
- parsing improvements
- reset item data position when a new report ID is detected.
Submitted by: Hans Petter Selasky
Tested on an HD3850 (RV670) on loan from Warren Block.
Currently, you need one of the following for this to be useful:
x11-drivers/xf86-video-radeonhd-devel (not tested)
xf86-video-ati from git (EXA works, xv is too fast)
xf86-video-radeonhd from git (EXA works, xv works)
There is no 3d support available from dri just yet.
MFC after: 2 weeks
o add Transaction Translator support (still missing ISOC xfers)
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
o enable TT and big-endian MMIO
o force a reset before ehci_init to get byte-select setup
Also go back to using USB_EHCI_BIG_ENDIAN_DESC at compile time to enable the
byteswapping and reduce diffs to the original commits.
This fixes the new USB stack on the Cambria board.
o implement URB_FUNCTION_ABORT_PIPE handling.
o remove unused code related with canceling the timer list for USB
drivers.
o whitespace cleanup and style(9)
Obtained from: hps's original patch
entry is a specific entry to override the generic NetMos entry so that
puc(4) will leave this device alone and let uart(4) claim it.
Submitted by: Navdeep Parhar nparhar @ gmail
Reviewed by: marcel
MFC after: 1 week
when determining the size of a BAR by writing all 1's to the BAR and
reading back the result, always operate on the full 64-bit size.
Reviewed by: imp
MFC after: 1 month
flag when calling bus_alloc_resource() to allocate resources from a parent
PCI bridge. For PCI-PCI bridges this asks the bridge to satisfy the
request using the prefetchable memory range rather than the normal
memory range.
Reviewed by: imp
Reported by: scottl
MFC after: 1 week
BAR could be allocated twice by different children of a vgapci0 device.
To fix this, change the vgapci0 device to track references on its associated
resources so that they are only allocated once from the parent PCI bus and
released when no children are using them. Previously this leaked a small
amount of KVA on at least some architectures.
We now explicitly enable INTx during bus_setup_intr() if it is needed.
Several of the ata drivers were managing this bit internally. This is
better handled in pci and it should work for all drivers now.
We also mask INTx during bus_teardown_intr() by setting this bit.
Reviewed by: jhb
MFC after: 3 days
- Added missing firmware for 5709 A1 controllers.
- Changed some debug statistic variable names to be more consistent.
Submitted by: davidch
MFC after: Two weeks
A while back, Warner changed the PCI bus code to reserve resources when
enumerating devices and simply give devices the previously allocated
resources when they call bus_alloc_resource(). This ensures that address
ranges being decoded by a BAR are always allocated in the nexus0 device
(or whatever device the PCI bus gets its address space from) even if a
device driver is not attached to the device. This patch extends this
behavior further:
- To let the PCI bus distinguish between a resource being allocated by
a device driver vs. merely being allocated by the bus, use
rman_set_device() to assign the device to the bus when it is owned
by the bus and to the child device when it is allocated by the child
device's driver. We can now prevent a device driver from allocating
the same device twice. Doing so could result in odd things like
allocating duplicate virtual memory to map the resource on some
archs and leaking the original mapping.
- When a PCI device driver releases a resource, don't pass the request
all the way up the tree and release it in the nexus (or similar device)
since the BAR is still active and decoding. Otherwise, another device
could later allocate the same range even though it is still in use.
Instead, deactivate the resource and assign it back to the PCI bus
using rman_set_device().
- pci_delete_resource() will actually completely free a BAR including
attemping to disable it.
- Disable BAR decoding via the command register when sizing a BAR in
pci_alloc_map() which is used to allocate resources for a BAR when
the BIOS/firmware did not assign a usable resource range during boot.
This mirrors an earlier fix to pci_add_map() which is used when to
size BARs during boot.
- Move the activation of I/O decoding in the PCI command register into
pci_activate_resource() instead of doing it in pci_alloc_resource().
Previously we could actually enable decoding before a BAR was
initialized via pci_alloc_map().
Glanced at by: bsdimp
This addresses interrupt storms that were noticed after enabling MSI
in drm. I think this is due to a loose interpretation of the PCI 2.3
spec, which states that a function using MSI is prohibitted from using
INTx. It appears that some vendors interpretted that to mean that they
should handle it in hardware, while others felt it was the drivers
responsibility.
This fix will also likely resolve interrupt storm related issues with
devices other than drm.
Reviewed by: jhb@
MFC after: 3 days
name i2c-address instead of reg. Change the OFW I2C probe to check both
locations for the address.
Submitted by: Marco Trillo
Reported by: Justin Hibbits
ready status. Most of controllers managed to issue coommand and set BUSY
bit almost simultaneously, before we will read it, but at least JMicron JMB363
don't. Ignore timeout errors to keep old behavior when error there was
impossible.
For me this fixes timeout errors on the first command after channel attach
or reinit. Boot in my case is not affected, as there is much time passing
between reset and next command giving reset time to complete.
done in other places. Until we have no support for command queueing we have
no any benefit from FBS, while enabling it only here somehow leads to
"port not ready" errors on Intel 63XXESB2 controller.
Tested by: Larry Rosenman <ler AT lerctr.org>
and partially r188903. Revert breaks new drives detection on reinit to the
state as it was before me, but fixes series of new bugs reported by some
people.
Unconditional queueing of ata_completed() calls can lead to deadlock if
due to timeout ata_reinit() was called at the same thread by previous
ata_completed(). Calling of ata_identify() on ata_reinit() in current
implementation opens numerous races and deadlocks.
Problems I was touching here are still exist and should be addresed, but
probably in different way.
drivers' probe routines. It allows not to sleep and so not drop Giant inside
ata_identify() critical section and so avoid crash if it reentered on
request timeout. Reentering of probe call checked inside of it.
Give device own knowledge about it's type (ata/atapi/atapicam). It is not
a good idea to ask channel status for device type inside ata_getparam().
Add softc memory deallocation on device destruction.
at irq install/uninstall time, but when we vt switch, we uninstall the
irq handler. When the irq handler is reinstalled, the modeset ioctl
happens first. The modeset ioctl is supposed to tell us that we can
disable vblank interrupts if there are no active consumers. This will
fail after a vt switch until another modeset ioctl is called via dpms
or xrandr. Leading to cases where either interrupts are on and can't
be disabled, or worse, no interrupts at all.
MFC after: 2 weeks
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
net/route.h.
Remove the hidden include of opt_route.h and net/route.h from net/vnet.h.
We need to make sure that both opt_route.h and net/route.h are included
before net/vnet.h because of the way MRT figures out the number of FIBs
from the kernel option. If we do not, we end up with the default number
of 1 when including net/vnet.h and array sizes are wrong.
This does not change the list of files which depend on opt_route.h
but we can identify them now more easily.
kernel dumping case.
ata_completed() may initiate ata_reinit() on error, that may lead to drives
attach or detach. Attach and detach are sending requests to drives and sleep
waiting for results. But ata_finish() can be called directly from
interrupt handler where sleeping is prohibited, so we must break this chain
somewhere. This place seems to fit best.
Disable MSI for nVidia MCP51 controller. Enabling MSI there leads to
unexpected errors and timeouts, that should not happen even if interrupts
are not working completely.
