floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
a vga.
* Fix broken logic in syscons for a failed probe.
* Fix AlphaStation 500/600 so that non-serial consoles are supported.
Submitted by: Thomas Valentino Crimi <tcrimi+@andrew.cmu.edu> (vga bits),
Andrew Gallatin <gallatin@cs.duke.edu> (AS500/AS600)
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
went backwards when interrupts were masked for more than one i8254
interrupt period. It sometimes went backwards when the i8254 counter
was reprogrammed. Neither of these should happen in normal operation.
Update the i8254 timecounter support variables atomically. Calling
timecounter functions from fast interrupt handlers may actually work
in all cases now.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
hopefully become a portable driver usable by all architectures. The api
support files have had to be copied to sys/alpha/include since userland
programs expect to find them in <machine/*.h>.
All the revision history of the i386 syscons has been retained by a
repository copy.
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
When bell is of "quiet" types, the console won't ring (or flush)
if the ringing process is in a background vty.
PR: i386/2853
- Modify the escape sequence 'ESC[=%d;%dB' so that bell pitch and
duration are set in hertz and msecs by kbdcontrol(1).
There will be a corresponding kbdcontrol patch.
PR: bin/6037
Submitted by: Kouichi Hirabayashi (kh@eve.mogami-wire.co.jp)
- Call isa_dmadone() whenever necessary to stop DMA and/or free bounce
buffers. Undead DMA corrupted the malloc freelist fairly consistently
in the following configuration: SLICE kernel, 2 floppy drives, no disk
in fd0, disk in fd1.
- Don't call fdc_reset() from fd_timeout(). Doing so gave an "extra"
interrupt which was usually misinterpreted as being for completion
of the next FDC command; the interrupt for completion of the next
FDC command was then usually misinterpreted... There were further
complications for interrupts latched by the soft-spl mechanism so
that they were delivered after all the h/w interrupts went away.
This caused at least wrong head settle delays and may be why the
FreeBSD floppy driver seems to munch floppies more than most floppy
drivers. The reset was unnecessary anyway in cases that didn't have
the bug described next, since is was repeated a little later for
the IOTIMEDOUT state. The state machine has complications to handle
resets correctly, so just use it.
- Don't call retrier() from fd_timeout(). The IOTIMEDOUT state needs
to be processed next, and it isn't valid to set to that state if
retrier() has aborted the current transfer. Doing so caused null
pointer panics after the previous bug was fixed.
Improved error handling:
- If an i/o is aborted, arrange to reset in the state machine before
doing the next i/o. New fdc flag for this. This fixes spurious
warnings and lengthy busy-waiting for the next i/o.
- Split STARTRECAL into RESETCOMPLETE and STARTRECAL and only check
for the results from reset if we actually reset. This fixes spurious
warnings for other paths to STARTRECAL. [Oops, it may break reset
handling for motor-off resets.]
Cleanups in fd_timeout():
- Renamed to fd_iotimeout() to make it clearer that it is only used
for i/o.
- Don't handle the bp == 0 case. This case can't happen for i/o.
- Don't check for controller-busy. We know it must be.
- Don't print anything. retrier() already prints too much for normal
errors.
- Fudge the state differently so that the state machine advances
fdc->retry and the status is invalid (perhaps this should fudge a
valid state like the one for WP).
- Style fixes.
controller reports a successful seek, it is very unlikely to report
seeking to a cylinder other than the one requested, but we check for
this, and botched the error handling for the requested_cylinder != 0
case. This error happened when the bug fixed in rev.1.52 of <sys/buf.h>
caused the head of buffer queue to change to one starting on a different
cylnder - the requested cylinder was found, but it wasn't what we
thought we requested. The fix is simply to arrange to reset the state
machine.
Corruption of the buffer queue seems to only have been a problem in the
floppy driver. Other drivers dequeue the head of the queue before doing
physical i/o on it, so the corruption at worse broke the elevator sort
order. Dequeueing breaks it anyway.
interupt level events. This needs a lot of cleanup, but has been working
here for a month or two.. originally needed for CAM integration
but that hasn't happenned yet. The probing state machines for each
handler should be replaced by a more generic state-service. It's
still quite messy in there..
is the kernel part of my commits, the userlevel stuff will be done in
a separate commit. Add the ability to suspend as well as hibernate to
syscons. Create a new virtual key like hibernate for suspend. Update
apm_bios.h to define more apm bios goodies.
There is only cdevsw (which should be renamed in a later edit to deventry
or something). cdevsw contains the union of what were in both bdevsw an
cdevsw entries. The bdevsw[] table stiff exists and is a second pointer
to the cdevsw entry of the device. it's major is in d_bmaj rather than
d_maj. some cleanup still to happen (e.g. dsopen now gets two pointers
to the same cdevsw struct instead of one to a bdevsw and one to a cdevsw).
rawread()/rawwrite() went away as part of this though it's not strictly
the same patch, just that it involves all the same lines in the drivers.
cdroms no longer have write() entries (they did have rawwrite (?)).
tapes no longer have support for bdev operations.
Reviewed by: Eivind Eklund and Mike Smith
Changes suggested by eivind.
over from the probe are now expected for incompatible UARTs that
deliver IRQs as a strobe (low) instead of a level (high).
Discard events on going-away devices too. Endless loops may have
been possible when an active pccard was removed.
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
miscconfigured case) if the port is the console. This fixes several
bugs:
- if all sioprobe()s failed, then the console driver followed null
pointers in cdevsw[].
- if the sioprobe() for the console failed but another sioprobe()
succeeded, then init hung early when the console couldn't be
opened.
- it was silly for the console to not be there after printing boot
messages on it.
Bugs introduced by this are hopefully no worse than old ones caused
by forcing the success of the `cn' level probe.
Only complain about an irq mismatch in the probe if the configured
irq doesn't become active, and then print the bitmap of irqs that
became active (including clock irqs) instead of just the first
(not including clock irqs).
Bugs reported by: msmith
a test of the irq number, and made failure of this test non-fatal.
Removed related unused complications for the APIC_IO case. Removed the
no-test3 flag.
Deverbosified the failure messages for the other tests. Removed the
per-port verbose flag - just use the general verbose flag.
Clean up (or if antipodic: down) some of the msgbuf stuff.
Use an inline function rather than a macro for timecounter delta.
Maintain process "on-cpu" time as 64 bits of microseconds to avoid
needless second rollover overhead.
Avoid calling microuptime the second time in mi_switch() if we do
not pass through _idle in cpu_switch()
This should reduce our context-switch overhead a bit, in particular
on pre-P5 and SMP systems.
WARNING: Programs which muck about with struct proc in userland
will have to be fixed.
Reviewed, but found imperfect by: bde
but doesn't do much of anything with it. I added it to siopnp_ids[]
and it was found and recognized as a serial port.
PR: 6605
Reviewed by: phk
Submitted by: Dave Marquardt <marquard@zilker.net>
This code will be turned on with the TWO options
DEVFS and SLICE. (see LINT)
Two labels PRE_DEVFS_SLICE and POST_DEVFS_SLICE will deliniate these changes.
/dev will be automatically mounted by init (thanks phk)
on bootup. See /sys/dev/slice/slice.4 for more info.
All code should act the same without these options enabled.
Mike Smith, Poul Henning Kamp, Soeren, and a few dozen others
This code does not support the following:
bad144 handling.
Persistance. (My head is still hurting from the last time we discussed this)
ATAPI flopies are not handled by the SLICE code yet.
When this code is running, all major numbers are arbitrary and COULD
be dynamically assigned. (this is not done, for POLA only)
Minor numbers for disk slices ARE arbitray and dynamically assigned.
- Set the correct value scp->font_size in init_scp().
- Set scp->font_size to FONT_NONE for VGA_MODEX.
Interim fix for a font problem:
- A kludge to display the correct font on some video cards.
We should be able to load multiple fonts to the VGA plane #2 and switch
between fonts by setting the font select register in the VGA sequencer.
It appears that the current code isn't functioning as expected on
some VGA cards (I have reports on Millenium and Mach64 cards). This is
either a bug in syscons or a hardware compatibility problem ;-<
This kludge will always load only one font set at a time and always use
the font page #0 on the plane #2. It is an interim kludge until
we find the exact cause and solution.
Small adjustment for mouse cursor handling:
- Turn off the mouse cursor early when changing video modes.
Video mode switch fixes:
- Stop the screen saver when changing video modes.
- Enclose the critical section with a pair of spltty()/splx().
- A kludge to prevent scrn_update() from accessing video memory in less-
critical sections in video mode change; artificially turn on the
UNKNOWN_MODE flag.
PR: bin/5899, bin/5907
Tested by: ache and a couple of users
OKed by: sos
* Figure out UTC relative to boottime. Four new functions provide
time relative to boottime.
* move "runtime" into struct proc. This helps fix the calcru()
problem in SMP.
* kill mono_time.
* add timespec{add|sub|cmp} macros to time.h. (XXX: These may change!)
* nanosleep, select & poll takes long sleeps one day at a time
Reviewed by: bde
Tested by: ache and others
"time" wasn't a atomic variable, so splfoo() protection were needed
around any access to it, unless you just wanted the seconds part.
Most uses of time.tv_sec now uses the new variable time_second instead.
gettime() changed to getmicrotime(0.
Remove a couple of unneeded splfoo() protections, the new getmicrotime()
is atomic, (until Bruce sets a breakpoint in it).
A couple of places needed random data, so use read_random() instead
of mucking about with time which isn't random.
Add a new nfs_curusec() function.
Mark a couple of bogosities involving the now disappeard time variable.
Update ffs_update() to avoid the weird "== &time" checks, by fixing the
one remaining call that passwd &time as args.
Change profiling in ncr.c to use ticks instead of time. Resolution is
the same.
Add new function "tvtohz()" to avoid the bogus "splfoo(), add time, call
hzto() which subtracts time" sequences.
Reviewed by: bde
on the IOAPIC being connected to the 8254 timer interrupt.
Verify that timer interrupts are delivered. If they aren't, attempt
a fallback to mixed mode (i.e. routing the timer interrupt via the 8259 PIC).
it runs at a constant frequency. This was less of an issue before,
because the TSC only interpolated in the HZ intervals, but now where
the timecounter is used all the way, this becomes much more visible.
Nit: Fix a printf which triggered the bde-filter.
Highlights:
* Simple model for underlying hardware.
* Hardware basis for timekeeping can be changed on the fly.
* Only one hardware clock responsible for TOD keeping.
* Provides a real nanotime() function.
* Time granularity: .232E-18 seconds.
* Frequency granularity: .238E-12 s/s
* Frequency adjustment is continuous in time.
* Less overhead for frequency adjustment.
* Improves xntpd performance.
Reviewed by: bde, bde, bde
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
with macros. This breaks if the functions are replaced by macros with
unsuitable semantics. Define a MAX() macro unconditionally instead.
max() is unsuitable since we need a constant expression. Don't define
MIN() - we never used min().
is "acquired". This fixes a TSC biasing error of about 10 msec when
pcaudio is active.
Update `time' before calling hardclock() when timer0 is being released.
This is not known to be important.
Added some delays in writertc(). Efficiency is not critical here, unlike
in rtcin(), and we already use conservative delays there.
Don't touch the hardware when machdep.i8254_freq is being changed but
the maximum count wouldn't change. This fixes jitter of up to 10 msec
for most small adjustments to machdep.i8254_freq. When the maximum
count needs to change, the hardware should be adjusted more carefully.
this using option "-b" to the boot blocks. It is smartest to compile
a font into your kernel (See LINT), but not mandatory, but apart from
the cursor you will see nothing on the screen until you load a font.
This mode allows XF86_VGA16 to run in 800x600 mode on otherwise unsupported
graphics hardware.
A number of buglets in the cursor handling in syscons may become
visible this way.
mode switch in ioctl.
Possibly related to PR: kern/4271
- A kludge: initialize scp->xpixel and ypixel even in the text mode.
If the console enters the `unknown' graphics mode via the ioctl KDSETMODE
(KD_GRAPHICS), these fields are not set (because syscons cannot know
the correct values), but set_mouse_pos() need to refer to these field
to adjust the mouse position.
- Turn off MOUSE_VISIBLE when switching video mode by ioctl.
- another new option: SC_MOUSE_CHAR
Define the first character code of four consecutive codes to be used for
the mouse cursor. Default codes are 0xd0 through 0xd3. Beware that
if you decide to use any codes outside the range of 0xc0-0xdf,
the mouse cursor may not look good, because of the way VGA displays
characters in 9-dot-wide character cells.
Requested by several people.
(This patch was tested by a person who recently reported, in the -current
ML, a page fault problem in the kernel (draw_mouse_iamge()) after
X server shutdown. The patch cured his problem.)
Don't touch/update the screen while manipulating font data.
Possibly related to PR: kern/4271
- Set up VGA in alphanumeric mode rather than graphics mode when
loading font into video memory. This will drastically reduce flicker.
PR: bin/2977
- Set up scp->font_size properly during video mode switch caused by
ioctl.
separate routine: scupdate() called from scrn_timer().
- Make sure that the screen is updated for the low-level console
routines sccngetc() and sccncheckc(). A new routine, sccnupdate(),
is introduced and will call scupdate() above.
Requested by: bde and msmith
OKed by: sos
from the low-level console routines sccngetc() and sccncheckc().
Submitted by: bde (a long time ago)
- Don't try to ring bell and immediately return from do_bell() while
device probe is in progress at boot time; the timeout queue is not
functional yet.
PR: kern/2424
- Stop running the screen saver after panic() is called: check
if `panicstr' is non-NULL during scrn_timer().
PR: kern/5314
- A new option: SC_DISABLE_REBOOT
The reboot key (usually Ctl-Alt-Del) will be ignored if this option
is defined. You may still have the reboot key defined in the keymap and
it won't cause error when the keymap is loaded, but it will be quietly
treated as nop.
OKed by: sos
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
so that existing programs which were compiled before the introduction
of the new mouse code and use these ioctls will run unmodified.
Suggested by msmith.
(accent_key + space does still print the accent letter too, as in
the previous commit.)
Requested by a couple of users.
- Clear the accent flag when the next_screen key is pressed.
- Added some comment lines regarding accent key processing.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
With a keymap with accent key definitions loaded to syscons, you press
an accent key followed by a regular letter key to produce an accented
letter. Press an accent key followed by the space bar to get the
accent letter itself.
Code is based on the ideas and work by jmrueda@diatel.upm.es and
totii@est.is.
PR: i386/4016
console.h
- Defined structures and constants for accent (dead) keys.
syscons.c, kbdtables.h
- When an accent key is pressed, set the corresponding index to
`accents'. If the next key is the space key, produce the accent char
itself. Otherwise search the accent key map entry, indexed by
`accents', for a matching pair of a regular char and an accented char.
- Added ioctl functions to set and get the accent key map (PIO_DEADKEYMAP
and GIO_DEADKEYMAP).
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
MS IntelliMouse, Kensington Thinking Mouse, Genius NetScroll,
Genius NetMouse, Genius NetMouse Pro, ALPS GlidePoint, ASCII
MieMouse, Logitech MouseMan+, FirstMouse+
- The `psm' driver is made to recognize various models of PS/2 mice
and enable their extra features so that their additional buttons and
wheel/roller are recognized. The name of the detected model will be
printed at boot time.
- A set of new ioctl functions are added to the `psm', `mse' and
`sysmouse' drivers so that the userland program (such as the X server)
can query device information and change driver settings.
- The wheel/roller movement is handled as the `Z' axis movement by the
mouse drivers and the moused daemon. The Z axis movement may be mapped
to another axis movement or buttons.
- The mouse drivers support a new, standard mouse data format,
MOUSE_PROTO_SYSMOUSE format which can encode x, y, and x axis movement
and up to 10 buttons.
/sys/i386/include/mouse.h
- Added some fields to `mousestatus_t' to store Z axis movement
and flag bits.
- Added the field `model' to `mousehw_t' to store mouse model code.
Defined model codes.
- Extended `mousemode_t'.
- Added new protocols and some constants for them.
- Added new ioctl functions and structures.
- Removed obsolete ioctl definitions.
/sys/i386/include/console.h
- Added `dz' field to the structure `mouse_data' to pass Z axis movement
to `syscons/sysmouse'.
- Removed LEFT_BUTTON, MIDDLE_BUTTON and RIGHT_BUTTON. Use button bits
defined in `mouse.h' instead.
/sys/i386/isa/psm.c
- Added a set of functions to detect various mice which have additional
features (wheel and buttons) unavailable in the standard PS/2 mouse.
- Refined existing ioctl functions and added new ones. Most important
of all is MOUSE_SETLEVEL which manipulates the output level of the driver.
While the output level remains zero, the output from the `psm' driver is
in the standard PS/2 mouse format (three bytes long). When the level
is set to one, the `psm' driver will send data in the extended format.
At the level two the driver uses the format which is native to the
connected mouse is used. (Meaning that the output from the device is
passed to the caller as is, unmodified.) The `psm' driver will pass
such extended data format as is to the caller if the output level is
two, but emulates the standard format if the output level is zero.
- Added kernel configuration flags to set initial resolution
(PSM_CONFIG_RESOLUTION) and acceleration (PSM_CONFIG_ACCEL).
- Removed the compile options PSM_ACCEL, PSM_CHECKSYNC and PSM_EMULATION.
Acceleration ratio is now specified by the kernel configuration flags
stated above. Sync check logic is refined and now standard.
The sync check can be turned off by the new kernel configuration flags
PSM_CONFIG_NOCHECKSYNC (0x100). PSM_EMULATION has been of little use.
- Summer clean up :-) Removed unused code and obsolete comments.
/sys/i386/isa/mse.c
- Created mseioctl() to deal with ioctl functions MOUSE_XXXX.
Most importantly, the MOUSE_SETLEVEL ioctl will change the
output format from the 5 byte format to the new, extended format
so that the caller can take advantage of Z axis movement and additional
buttons.
- Use constants defined in `mouse.h' rather than magic numbers.
/sys/i386/isa/syscons.c
- Changed scioctl() to reflect the new `console.h' and some of the new
ioctls defined in `mouse.h'. Most importantly, the MOUSE_SETLEVEL
ioctl will change the `sysmouse' output format from the MouseSystems
5 byte format to the new, extended format so that the caller can
take advantage of Z axis movement and additional buttons.
- Added support for double/triple click actions of the left button and
single click action of the right button in the virtual console. The
left button double click will select a word under the mouse pointer.
The triple click will select a line and the single click of the right
button will extend the selected region to the current position of
the mouse pointer. This will make the cut/paste support more compatible
with xterm.
/sys/i386/isa/kbdio.h
- Added PSM_INTELLI_ID.
checking the BIOS video mode paramter table. Now syscons uses the
parameter table even if some bits in the table are different from the
current VGA register settings.
Even if comp_vgaregs() finds that the BIOS video parameter table looks
totally unfamiliar to it, syscons allows the user to change the
current video mode to some modes which are based on the VGA 80x25
mode. They are VGA 80x30, VGA 80x50, VGA 80x60. In this case the user
will be warned, during boot, that video mode switching is only
paritally supported on his machine.
PR: bin/4477
in <machine/cpu.h>. Moved the declarations to <machine/cputypes.h>.
Fixed style bugs in the moved code. Fixed everything that depended on
the nested include. Don't include <machine/cpu.h> (in the changed files)
unless something in it is used directly.
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
flicker won't occur when set_border() is called.
- Properly restore the border color when switching virtual consoles.
Pointed out by: tony@dell.com
OKed by: sos
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
check the value and caused kernel panic when a large value was given.
- Move the configuration option SC_HISTORY_SIZE from syscons.h to
syscons.c.
- Define the maximum total number of history lines of all consoles.
It is SC_HISTORY_SIZE*MAXCONS or 1000*MAXCONS; whichever is larger.
CONS_HISTORY will allow the user to set the history size up to
SC_HISTORY_SIZE unconditionally (or the current height of the console
if it is larger than SC_HISTORY_SIZE). If the user requests a larger
buffer, it will be granted only if the total number of all allocated
history lines and the requested number of lines won't exceed the maximum.
- Don't free the previous history buffer and leave the history buffer
pointer holding a invalid pointer. Set the pointer to NULL first, then
free the buffer.
PR: bin/4592
floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.
Reviewed by: j@uriah.heep.sax.de (J Wunsch)
Hide the bogus FDC ``chip type'' display behind a (mostly) undocumented
option, since people started to trust the bogus claim. Once we're going
to handle 2.88 MB controllers, we have to redo the chip detection, by
now just leave it hidden.
size in terms of lines (instead of bytes). When changing video mode
in ioctl SW_XXX commands, syscons checks scp->history_size and
allocate a history buffer at least as large as the new screen size.
(This was unnecessary before, because HISTORY_SIZE was as large as 100
lines and this is bigger than the maximum screen size: 60 lines).
Similar adjustment is done in ioctl CONS_HISTORY command too.
PR: kern/4169
Reviewed by: sos
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
Made NEW_STRATEGY default.
Removed misc. old cruft.
Centralized simple locks into mp_machdep.c
Centralized simple lock macros into param.h
More cleanup in the direction of making splxx()/cpl MP-safe.
Several new fine-grained locks.
New FAST_INTR() methods:
- separate simplelock for FAST_INTR, no more giant lock.
- FAST_INTR()s no longer checks ipending on way out of ISR.
sio made MP-safe (I hope).
Add support for MODEX 320x240x256color with "unchained" adressing, giving
access to all 256K on all VGA's, those with that much memory that is :)
Also make sysmouse use the right resolution in graphics modes.
- removed TEST_ALTTIMER.
- removed APIC_PIN0_TIMER.
- removed TIMER_ALL.
apic_vector.s:
- new algorithm where a CPU uses try_mplock instead of get_mplock:
if successful continue as before.
if fail set ipending bit, mask INT (to avoid recursion), cleanup & iret.
This allows the CPU to return to successful work, while the ISR will be run
by the CPU holding the lock as part of the doreti dance.
1. Add new interface, add_scrn_saver()/remove_scrn_saver(), to declare
loading/unloading of a screen saver. The screen saver calls these
functions to notify syscons of loading/unloading events.
It was possible to load multiple savers each of which will try to
remember the previous saver in a local variable (`old_saver'). The
scheme breaks easily if the user load two savers and unload them in a
wrong order; if the first saver is unloaded first, `old_saver' in the
second saver points to nowhere.
Now only one screen saver is allowed in memory at a time.
Soeren will be looking into this issue again later. syscons is
becoming too heavy. It's time to cut things down, rather than adding
more...
2. Make scrn_timer() to be the primary caller of the screen saver
(*current_saver)(). scintr(), scioctl() and ansi_put() update
`scrn_time_stamp' to indicate that they want to stop the screen saver.
There are three exceptions, however.
One is remove_scrn_saver() which need to stop the current screen saver
if it is running. To guard against scrn_timer() calling the saver during
this operation, `current_saver' is set to `none_saver' early.
The others are sccngetc() and sccncheckc(); they will unblank the
screen too. When the kernel enters DDB (via the hot key or a
break point), the screen saver will be stopped by sccngetc().
However, we have a reentrancy problem here. If the system has been in
the middle of the screen saver...
(The screen saver reentrancy problem has always been with sccnputc()
and sccngetc() in the -current source. So, the new code is doing no
worse, I reckon.)
3. Use `mono_time' rather than `time'.
4. Make set_border() work for EGA and CGA in addition to VGA. Do
nothing for MDA.
Changes to the LKM screen saver modules will follow shortly. YOU NEED
TO RECOMPILE BOTH SCREEN SAVERS AND KERNEL AS OF THESE CHANGES.
Reviewed by: sos and bde
and released. It should use `spcl' consistently in both cases,
otherwise shift/control/alt state may not be correctly set/reset.
(Even with this fix, you can still make syscons confused and fail to
change internal state if you really want to, by installing a really
arcane and artificial keymap.)
PR: i386/4030
Reviewed by: sos
cursor (CHAR_CURSOR)
1. Reduced the number of calls to set_destructive_cursor(). The
destructive cursor produced noticeable overhead on the system. It was
caused by draw_cursor_image() calling set_destructive_cursor() every
so often.
set_destructive_cursor() absolutely needs to be called when
a) the character code under the cursor has changed either because
the cursor moved or because the screen was updated or the mouse
pointer overlapped the cursor.
b) Or a new font has been loaded,
c) or the video mode has been changed,
d) or the cursor shape has been changed,
e) or the user switched virtual consoles.
2. Turn off the configuration flag CHAR_CURSOR (destructive cursor) in
scattach() if we have a non-VGA card. The destructive cursor works
only for VGA.
3. Removed redundant calls to set_destructive_cursor() in some places.
4. Fixed the "disappearing mouse pointer" problem. The mouse pointer
looked hidden under the destructive cursor when it overlaped the cursor.
A slightly different version of the patch was reviewd and OKed by
sos and ache.
Add a new configuration flag, KBD_NORESET (0x20) to tell scprobe() not
to reset the keyboard.
IBM ThinkPad 535 has the `Fn' key with which the user can perform
certain functions in conjunction with other keys. For example, `Fn' +
PageUP/PageDOWN adjust speaker volume, `Fn' + Home/End change
brightness of LCD screen. It can also be used to suspend the system.
It appears that these functions are implemented at the keyboard level
or the keyboard controller level and totally independent from BIOS or
OS. But, if the keyboard is reset (as is done in scprobe()), they
become unavailable. (There are other laptops which have similar
functions associated with the `Fn' key. But, they aren't affected by
keyboard reset.)
ThinkPad 535 doesn't have switches or buttons to adjust brightness and
volume, or to put the system into the suspend mode. Therefore, it is
essential to preserve these `Fn' key functions in FreeBSD. The new
flag make scprobe() skip keyboard reset.
If this flag is not set, scprobe() behaves in the same say as before.
(If we only knew a way to detect ThinkPad 535, we could skip keyboard
reset automatically, but...)
adapter during the system boot. It always assumes there is at least a
monochrome adapter.
This is rather strange assumption. If there is no dispaly adapter, the
console driver cannot be any good...
In this patch, scinit() is split into two parts; the first part is
now called scvidprobe() which will detect the presence of video card
at the CGA or MONO buffer address and returns TRUE if found. It is
called during sccnprobe() and scprobe(). Both will fail if no video
card is found.
The second part, whose name stays the same as before, scinit(), is
called from sccninit() and scattach() to complete initialization of
the found video card.
The keyboard probe code is moved from scprobe() to sckbdprobe();
scprobe() now calls scvidprobe() and sckbdprobe() to carry out device
probe. (This is rather a cosmetic change, but it sure makes the code
look better organized.)
The problem pointed out by Joerg.
speed using the boot blocks, instead of a hardcoded value stuck in the
kernel. This way, you can have systems using the same kernel but different
console speeds.
Add a sysctl entry for changing the system console speed.
Lock the user tty speed to match the system console speed.
Nuke CONSPEED.
Reviewed by: bde
When an ioctl command SW_XXXX is issued, scioctl() checks if the font
appropriate for the specified mode is already loaded. The check was
correctly done for 8 line and 16 line fonts, but not for 14 line font.
The symbols FONT_8, FONT_14 and FONT_16 were defined as numbers but
were sometimes treated as bit flags. They are now defined as bit
flags.
2) screen blinking (two fixes)
Removed a redundant call to timeout() in do_bell().
Don't let blink_screen() write to the video buffer if the screen is in
the graphics (UNKNOWN) mode.
3) screen saver timeout
The ioctl command CONS_BLANKTIME sets the screen saver's timeout. The
value of zero will disable the screen saver. If the screen saver is
currently running it should be stopped.
4) border color and destructive cursor (two fixes)
The border color and the cursor type can be changed via escape
sequences. But only VGA can change the border color and set the
cursor type to destructive (CHAR_CURSOR) in the current syscons.
scan_esc() failed to check this.
Reviewed by: sos
simplifies some assumptions and stops some code compile problems.
This should fix the compile hiccup in PR#3491, but smp kernel profiling
isn't likely to be fixed by this.
1) i586_bcopy() problem
There have been a number of reports that the syscons doesn't work
properly if i586_bcopy() is enabled.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is that the system looks frozen during device probe or just
before the main installation menu. The workaround was to specify the
flag 0x01 to the npx device so that i586_bcopy() is disabled.
The patch forces the syscons to call generic_bcopy() when copying
to/from the video memory, even if CPU is Pentium and i586_bcopy() is
enabled. i586_bcopy() is still called for copy operations between
non-video memory regions.
PR: kern/2277, kern/3066, kern/3107, kern/3134
2) video mode parameter table problem
The syscons reads and uses the video mode parameter table provided by
the VGA BIOS to set VGA registers when changing video mode and
modifying font data. It appears that in some VGA BIOSes the table is
not ordered as the syscons expects, and this leads to screen
corruption.
The problem prevented users from installing 2.2(.1)-RELEASE. The
symptom is the corrupt screen or strange vertical lines soon after the
kernel is loaded into memory (just after the kernel decompression).
The patch performs simplistic test and if it fails, set video_mode_ptr
to NULL so that the video mode switching won't happen.
This is an interim kludge. There should be a better way to deal with
the problem.
PR: kern/2498, conf/2775, conf/3354
Reviewed by: sos
Tested by: PR originators (not all of them, though)
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
resetting the keyboard.
Well, sorry, this bug is totally my fault. I DID intend to preserve
them, but somehow I failed.
The bug puts some old keyboard controllers in a strange state,
resulting in keyboard freeze or random key input.
The fix closes PR kern/3067.
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
(see LINT). There is a new low-level console type that is more suitable
for use with gdb-remote.
Fixed setting of speed at probe time for the serial console (if any).
Reviewed by: dfr
change typematic rate, or the X server (XFree86 or Accelerated X)
starts up.
So far, there have been two independent reports from Dell Latitude XPi
notebook/laptop owners. The Latitude seems to be the only system which
suffers from this problem. (I don't know the problem is with the
entire Latitude line or with only some Latitude models) No problem
report has been heard about other systems (I certainly cannot
reproduce the problem in my -current and 2.2 systems).
In 3.0-CURRENT, 2.2-RELEASE and 2.2-GAMMA-970310, when programming the
keyboard LED/repeat-rate, `set_keyboard()' in `syscons' tells the
keyboard controller not to generate keyboard interrupt (IRQ1) and then
enable tty interrupts, expecting the keyboard interrupt doesn't occur.
It appears that somehow Latitude's keyboard controller still generates
the keyboard interrupt thereafter, and `set_keyboard()' doesn't see
the return code from the keyboard because it is consumed by the
keyboard interrupt handler.
The patch entirely disables tty interrupts while setting LED and
typematic rate in `set_keyboard()', making the routine behave more
like the previous versions of `syscons' (versions in 2.1.X and
2.2-ALPHA, -BETA, and some -GAMMAs). The reporter said this patch
eliminated the problem.
(I also found another typo/bug, but the reporter and I found that it
wasn't the cause of the problem...)
This should go into RELENG_2_2.
Warning: this won't work yet with PCVT_SCANSET=2 along in early
console mode (boot -c, or boot -d).
A big thanks to Kazutaka, and a word of apologies for delaying the
review for that long time...
Submitted by: yokota@zodiac.mech.utsunomiya-u.ac.jp (Kazutaka YOKOTA)
valid signals, else return EINVAL for ioctl VT_SETMODE.
this fixes a problem that anybody with vty access can panic the system.
2.2-Candidate (and 2.1.0 I believe)
Reviewed-by: sos
changes, so don't expect to be able to run the kernel as-is (very well)
without the appropriate Lite/2 userland changes.
The system boots and can mount UFS filesystems.
Untested: ext2fs, msdosfs, NFS
Known problems: Incorrect Berkeley ID strings in some files.
Mount_std mounts will not work until the getfsent
library routine is changed.
Reviewed by: various people
Submitted by: Jeffery Hsu <hsu@freebsd.org>
The PS/2 mouse device responds to a reset command with a sequence of
ACK(fa), RESULT(aa) and ID(00). Most PS/2 mice immediately returns
ACK, but spend sometime before sending RESULT. The Armada takes time
before ACK; extra delay is necessary before the call to read ACK.
The problem was reported in comp.unix.bsd.freebsd.misc and the patch
was tested by the reporter. No PR was filed, by the way.
with <= 100 usec between each character arrival time. This didn't happen
until rev.1.75 of clock.c because DELAY(100) used to delay for closer to
80 usec than 100 usec, and the minimum time between character arrivals is
87.8 usec at the maximum supported speed of 115200 bps 8N1.
Clear DCD timestamp flag on close (the input timestamp flag is already
cleared).
key "print scrn".
It used to stop at the first non-open vty, now it skips the non-open
ones and thereby enable one to cycle around all open vty by pressing
"print scrn".
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
- don't uselessly initialize the fifo "DMA" bit at attach time.
- initialize the fifo "DMA" bit at open time. Without this, the device
interrupts for every character received, reducing input performance
to that of an 8250.
- don't uselessly initialize the fifo trigger level to 8 (scaled to
256) at attach time.
- don't scale the fifo trigger level to 512 bytes. The driver's pseudo-
dma buffer has size 256, so it can't handle bursts of size 512 or 256.
It should be able to handle the second lowest ftl (2 scaled to 64).
- don't reset the fifos in siostop(). Reset triggers a hardware bug
involving wedging of the output interrupt bit This workaround
unfortunately requires ESP support to be configured.
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
actually harmless.
2. Fixed code to match comment in scintr().
3. Don't allow even root to take control of the machine when securelevel > 0.
I've secured the accesses to PSL_IOPL in all drivers and asked pst to
review it, but he seems to be busy. Write access to /dev/kmem and
other critival devices currently leaks across raisings of securelevel
via open fd's, so there may as well be a similar leak for PSL_IOPL.
4. (Most important.) Don't corrupt memory beyond the screen buffers if
the cursor happens to be off the 80x25 screen when syscons starts.
5. Fix console cursor update (not perfect yet).
Submitted by: bruce
~
getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
Inspired by: The Nomads
appearance of this bug was the malfunctioning -M option in GNU tar (it
worked only by explicitly specifying -L).
Reviewed by: bde, and partially corrected accoring to his comments
Candidate for 2.2, IMHO even for 2.1.6.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
TIMER_FREQ.
Fixed missing splx() in scrn_timer(). The bug was harmless because of the
undocumented behaviour that the ipl is automatically restored for timeout
functions (see softclock()). Perhaps we should depend on this behaviour.
Fixed the ddb fix in rev.1.176. The in_debugger flag was no use because
it only works when the debugger is entered via the keyboard hotkey. The
debugger may be entered for breakpoints and traps, and the console putc
routine has no way of knowing when it was, so the console putc routine
must (almost?) always remove the cursor image.
Not fixed: console switching in ddb doesn't work (ISTR it working), and
console 0 shouldn't be switched to for the debugger hotkey unless console
0 is /dev/console.
Fixed side effects from calling add_keyboard_randomness() in the console
getc routine by not calling it. add_keyboard_randomness() currently
always reenables interrupts on 386's and 486's. This is very bad if the
console getc routine is called from the debugger and the debugger was
entered with interrupts disabled.
Fixed preservation of initial screen and now-bogus comment about it. It
was broken by setting the initial scr_buf to `buffer' instead of Crtat.
`buffer' was full of nulls and the first scroll cleared everything above
the things written through syscons.
Submitted by: bruce (bde@freebsd.org)
bit (0x0008) in the sc driver configuration line. This way it's easy to
boink a generic kernel.
Also, document and place in an opt_ file the #define's for overriding which
serial port is the system console.
Approved by: sos
there is keyboard input.
The mousepointer is shown again immediately if moved.
Also a function pointer used to install a userwritten extra
ioctl handler (sc_user_ioctl). This way its is possible to
install user defined videomodes etc etc. No further changes
should be in the kernel.
divisor latch registers if the registers wouldn't change.
Use the default console cfcr setting while setting the divisor
latch registers for console i/o. Input may be messed up by
transiently changing the cfcr.
Use a usual cfcr setting while setting the divisor latch registers
in the probe. This shouldn't matter, but this is not the place to
test the UART's handling of 5 bit words.
Removed a stale devfs comment.
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike
Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>
and xdm, possibly in general.
What was happening was that the server was doing a tcsetattr(.. TCSADRAIN)
on the mouse fd after a write. Since /dev/sysmouse had a null t_oproc,
the drain failed with EIO. Somehow this spammed XFree86 (!@&^#%*& binary
release!!), and the driver was left in a bogus state (ie: switch_in_progress
permanently TRUE).
The simplest way out was to implement a dummy scmousestart() routine to
accept any characters from the tty system and toss them into the void.
It would probably be more correct to intercept scwrite()'s to the mouse
device, but that's executed for every single write to the screen.
Supplying a start routine to eat the characters is only executed for the
mouse port during startup/shutdown, so it should be faster.
This enables other consumers of the mouse, to get it info via
moused/syscons.
In order to use it run moused (from sysconfig), and then tell
your Xserver that it should use /dev/sysmouse (mknod sysmouse c 12 128)
and it a mousesystems mouse. Everybody will be happy then :)
Remember that moused still needs to know what kind of mouse you
have..
Comments welcome, as is test results...
(A pointer to a const was misused to avoid loading loading the same
value twice, but gcc does exactly the same optimization automatically.
It can see that the value hasn't changed.)
If you define this, it means your keyboard is actually probable using the
brain-dammaged probe routine in syscons, and if the keyboard is NOT found,
then you don't want syscons to activate itself further.
This makes life sane for those of us who use serial consoles most of the
time and want "the right thing" to happen when we plug a keyboard in.
during phk's staticize/cleanup commits. pstat needs it, the MAXCONS
option is not visible anywhere else, and pstat uses it to find the bounds
of the sccons[MAXCONS] array, which varies.
Saves about 280 butes of source per driver, 56 bytes in object size
and another 56 bytes moves from data to bss.
No functional change intended nor expected.
GENERIC should be about one k smaller now :-)
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
via an ioctl (MOUSE_ACTION).
Fixed a couple of bugs (destructive cursor, uncut, jitter).
Now applications can use the mouse via the MOUSE_MODE ioctl, its
possible to have a signal sent on mouseevents, makeing an event loop
in the application take over mouseevents.
Real support for a Textmode mousecursor, works by reprogramming the
charset. Together with this support for cut&paste in text mode.
To use it a userland daemon is needed (moused), which provides
the interface to the various mice protokols.
Bug fixes here and there, all known PR's closed by this update.
Original version by John Hay.
Simplified timestamp code by reading the time exactly when necessary.
This may slow down the interrupt handler with extra calls to microtime(),
but only in bad configurations - the input fifo should normally be
disabled if timestamps on input are being used, since otherwise the
timestamp won't be precisely associated with any particular input event.
The interrupt handler remains slowed down by one test and branch for
each input (and now DCD change) event - avoiding this is not practical
yet.
The simplifications also fixed:
- timestamps for input sometimes being clobbered by output and modem
status interrupts.
- valid timestamps not being available unless the port is configured with
vector siointrts. siointrts no longer exists.
- compiler warnings about siointr* in some configurations.
Simplified timestamp and probe code by depending on recent changes in
microtime() and DELAY() to preserve the interrupt enable flag.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
unreasonable time. I've got a PCI mainboard that simply doesn't grok
it, so continuing with a warning (and a keyboard that's working
nevertheless :) seems to be better than spin-looping forever.
time. The results are currently ignored unless certain temporary options
are used.
Added sysctls to support reading and writing the clock frequency variables
(not the frequencies themselves). Writing is supposed to atomically
adjust all related variables.
machdep.c:
Fixed spelling of a function name in a comment so that I can log this
message which should have been with the previous commit.
Initialize `cpu_class' earlier so that it can be used in startrtclock()
instead of in calibrate_cyclecounter() (which no longer exists).
Removed range checking of `cpu'. It is always initialized to CPU_XXX
so it is less likely to be out of bounds than most variables.
clock.h:
Removed I586_CYCLECTR(). Use rdtsc() instead.
clock.c:
TIMER_FREQ is now a variable timer_freq that defaults to the old value of
TIMER_FREQ. #define'ing TIMER_FREQ should still work and may be the best
way of setting the frequency.
Calibration involves counting cycles while watching the RTC for one second.
This gives values correct to within (a few ppm) + (the innaccuracy of the
RTC) on my systems.
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
Always delay using one inb(0x84) after each i/o in rtcin() - don't
do this conditional on the bogus option DUMMY_NOPS not being defined.
If you want an optionally slightly faster rtcin() again, then inline
it and use a better named option or sysctl variable. It only needs
to be fast in rtcintr().
clock interrupts.
Keep a 1-in-16 smoothed average of the length of each tick. If the
CPU speed is correctly diagnosed, this should give experienced users
enough information to figure out a more suitable value for `tick'.
quite work yet, so the heart of it is disabled.
Added bdev and cdev args to dsopen().
drivers:
Fixed device names, links, minor numbers and modes.
wd.c:
Started actually supporting devfs.
diskslice.h:
Added devfs tokens to structs (currently 576 of them per disk! :-().
subr_diskslice.c:
Create devfs entries in dsopen() and (unsuccessfully) attempt to make
them go away at the right times. DEVFS is #undefed at the start so
that this shouldn't cause problems.
fd and wt drivers need bounce buffers, so this normally saves 32K-1K
of kernel memory.
Keep track of which DMA channels are busy. isa_dmadone() must now be
called when DMA has finished or been aborted.
Panic for unallocated and too-small (required) bounce buffers.
fd.c:
There will be new warnings about isa_dmadone() not being called after
DMA has been aborted.
sound/dmabuf.c:
isa_dmadone() needs more parameters than are available, so temporarily
use a new interface isa_dmadone_nobounce() to avoid having to worry
about panics for fake parameters. Untested.
variants, idea taken from NetBSD clock.c.
At least year calculation was wrong, pointed by Bruce.
Use different strategy to store year for BIOS without RTC_CENTURY
unintentionally committed):
- the fifo was completely disabled for low speeds. Apart from being
unnecessarily inefficient, this invalidated com->tx_fifo_size.
- `ftl' became a bogus name.
- the 16650 probe breaks the COM_NOFIFO() case and has other bugs
(disabled, not fixed).
Fixed bogus change of the fifo settings for the non-speed of 0. This
bug made the above fifo bug occur even at non-low speeds.
Fixed the modes of the cua devices. It isn't possible to set the uid
and gid correctly since the kernel can't know who uucp.dialer is.
Register the devswitch at device attach time. SYSINIT() is not
the right way to initialize devswitches (if anything :->).
Eventually, the devswitch should be deregistered at device detach
and/or unload time and reregistered at device attach time ... Then
some com->gone tests could be removed.
Cleaned up some other recent changes.
getmajorbyname() which were a better (sigh) temporary interface to
the going-away devswitches.
Note that SYSINIT()s to initialize the devswitches would be fatal
in syscons.c and pcvt_drv.c (and are bogus elsewhere) because they
get called independently of whether the device is attached; thus
devices that share a major clobber each other's devswitch entries
until the last one wins.
conf.c:
Removed stale #includes and comments.
device must be configured. It's hard to tell whether a reset function
should be noreset or nullreset since reset functions are never called.
Most drivers use nullreset but noreset has the advantage of complaining
if somehow gets called).
Removed old aliases d_rdwr_t and d_ttycv_t for d_read_t/d_write_t and
d_devtotty_t.
Sorted declarations of switch functions into switch order.
Removed duplicated comments and declarations of nonexistent switch
functions.
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
to get the definitions of TRUE and FALSE which happen to be defined in
a deeply nested include.
Added nearby #includes of <sys/conf.h> where appropriate.
- Don't print out meaningless iCOMP numbers, those are for droids.
- Use a shorter wait to determine clock rate to avoid deficiencies
in DELAY().
- Use a fixed-point representation with 8 bits of fraction to store
the rate and rationalize the variable name. It would be
possible to use even more fraction if it turns out to be
worthwhile (I rather doubt it).
The question of source code arrangement remains unaddressed.
conflicted with S3 graphics cards. Now users should put sio[2-3]
in the config file if the hardware exisst, even if the probe is
certain to fail due to an interrupt conflict. Otherwise, ports
sharing the interrupt may fail the probe if the system is warm
booted while sio[2-3] are active (perhaps under another OS). The
same problem for nonstandard ports is now handled better than
before.
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
totally dynamic.
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
it `const' to inhibit compiler warnings.
Added #include of <pccard/driver.h> to get prototypes. <pccard/slot.h>
is still necessary for its side effect of exporting non-slot things.
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
floppies must have been random in 2.x since we reintroduced sorting
on b_pblkno on 1995/03/18. Drivers still initialize b_cylin/b_resid
although this is no longer used.
Removed unused, wrong function fdsize(). (Returning 0 means that the
device exists and has size 0, not that the device doesn't exist.
swaponvp() allows for size 0 by stupidly calling the d_psize function
twice if the size isn't 0. setdumpdev() doesn't allow for it.)
Continued removing /* ARGSUSED */ from drivers.
misplaced extern declarations (mostly prototypes of interrupt handlers)
that this exposed. The prototypes should be moved back to the driver
sources when the functions are staticalized.
Added idempotency guards to <machine/conf.h>. "ioconf.h" can't be
included when building LKMs so define a wart in bsd.kmod.mk to help
guard against including it.
/dev/random is now a part of the kernel! you will need to make
the device in /dev: sh MAKEDEV random
and take a look at some test code in src/tools/test/random.
to <machine/conf.h>. conf.h was mechanically generated by
`grep ^d_ conf.c >conf.h'. This accounts for part of its ugliness. The
prototypes should be moved back to the driver sources when the functions
are staticalized.
This code will only be included in your kernel if you have
'options DEVRANDOM', but that will fall away in a couple of days.
Obtained from: Theodore Ts'o, Linux
Fix the tests for being a console by reverting to the ones that
were used before the the RB_SERIAL changes. RB_SERIAL only needs
to be tested in one place. The initialization of comconsole was
wrong before the RB_SERIAL changes for the COMCONSOLE case. This
may have been the cause of the unnecessary changes.
Start eliminating #includes of <i386/i386/cons.h>. This header is
supposed to be included from <machine> although it should be
completely machine-independent and included from <sys>.
Remove a wrong XXX comment. `comconsole' is used to test for being
a console and even the tests for deciding the default termios state
are necessary (the semi-reentrant i/o routines don't handle ordinary
device i/o).
cy.c:
Sync with sio.c. The console tests are present but always fail.
free-run and doing a subtract in microtime() rather than resetting the
counter to zero at every clock tick. In combination with the changes to
kern_clock.c, this should eliminate all the immediately obvious sources
of systematic jitter in timekeeping on Pentium machines.
the first one in the config has priority. They can be switched using
userconfig().
i386/i386/conf.c:
Initialize the shared syscons/pcvt cdevsw entry to `nx'.
Add cdevsw registration functions.
Use devsw functions of the correct type if they exist.
i386/i386/cons.c:
Add renamed syscons entry points to constab.
i386/i386/cons.h:
Declare the renamed syscons entry points.
i386/i386/machdep.c:
Repeat console initialization after userconfig() in case the current
console has become wrong. This depends on cn functions not wiring down
anything important.
sys/conf.h:
Declare new functions.
i386/isa/isa.[ch]:
Add a function to decide which display driver has priority. Should be
done better.
i386/isa/syscons.c:
Rename pccn* -> sccn*.
Initialize CRTC start address in case the previous driver has moved it.
i386/isa/syscons.c, i386/isa/pcvt/*
Initialize the bogusly shared variable Crtat dynamically in case the
stored value was changed by the previous driver.
Initialize cdevsw table from a template.
Don't grab the console if another display driver has priority.
i386/isa/syscons.h, i386/isa/pcvt/pcvt_hdr.h:
Don't externally declare now-static cdevsw functions.
i386/isa/pcvt/pcvt_hdr.h:
Set the sensitive hardware flag so that pcvt doesn't always have lower
priority than syscons. This also fixes the "stupid" detection of the
display after filling the display with text.
i386/isa/pcvt/pcvt_out.c:
Don't be confused the off-screen cursor offset 0xffff set by syscons.
kern/subr_xxx.c:
Add enough nxio/nodev/null devsw functions of the correct type for syscons
and pcvt.
changes to allow devices that don't probe (e.g. /dev/mem)
to create devfs entries
this required giving 'configure' its own SYSINIT entry
so we could duck in just before it with a DEVFS init
and some device inits..
my devfs now looks like:
./misc
./misc/speaker
./misc/mem
./misc/kmem
./misc/null
./misc/zero
./misc/io
./misc/console
./misc/pcaudio
./misc/pcaudioctl
./disks
./disks/rfloppy
./disks/rfloppy/fd0.1440
./disks/rfloppy/fd1.1200
./disks/floppy
./disks/floppy/fd0.1440
./disks/floppy/fd1.1200
also some sligt cleanups.. DEVFS needs a lot of work
but I'm getting back to it..
This is still very green, but I have managed to get my modem working.
Lots of work still to do, but now at least we can commit it. /phk
Reviewed by: phk
Submitted by: Andrew McRae <andrew@mega.com.au>
for return values. It just so happens that in the cases where it is likely
to fail, it is okay to change the M_NOWAIT to M_WAITOK -- and all will
be well. This problem was manfest as a panic very regularly on a 4MB
system right after bootup.
hardware. Set the sleep-on flag for the address so there is more
than a small chance that the sleep address is actually used (this
used to work by timing out). Don't bother clearing the sleep-on
flag after a timeout here or elsewhere since leaving it set just
generates a few null calls to wakeup().
Introduce TS_CONNECTED and TS_ZOMBIE states. TS_CONNECTED is set
while a connection is established. It is set while (TS_CARR_ON or
CLOCAL is set) and TS_ZOMBIE is clear. TS_ZOMBIE is set for on to
off transitions of TS_CARR_ON that occur when CLOCAL is clear and
is cleared for off to on transitions of CLOCAL. I/o can only occur
while TS_CONNECTED is set. TS_ZOMBIE prevents further i/o.
Split the input-event sleep address TSA_CARR_ON(tp) into TSA_CARR_ON(tp)
and TSA_HUP_OR_INPUT(tp). The former address is now used only for
off to on carrier transitions and equivalent CLOCAL transitions.
The latter is used for all input events, all carrier transitions
and certain CLOCAL transitions. There are some harmless extra
wakeups for rare connection- related events. Previously there were
too many extra wakeups for non-rare input events.
Drivers now call l_modem() instead of setting TS_CARR_ON directly
to handle even the initial off to on transition of carrier. They
should always have done this. l_modem() now handles TS_CONNECTED
and TS_ZOMBIE as well as TS_CARR_ON.
gnu/isdn/iitty.c:
Set TS_CONNECTED for first open ourself to go with bogusly setting
CLOCAL.
i386/isa/syscons.c, i386/isa/pcvt/pcvt_drv.c:
We fake carrier, so don't also fake CLOCAL.
kern/tty.c:
Testing TS_CONNECTED instead of TS_CARR_ON fixes TIOCCONS forgetting to
test CLOCAL. TS_ISOPEN was tested instead, but that broke when we disabled
the clearing of TS_ISOPEN for certain transitions of CLOCAL.
Testing TS_CONNECTED fixes ttyselect() returning false success for output
to devices in state !TS_CARR_ON && !CLOCAL.
Optimize the other selwakeup() call (this is not related to the other
changes).
kern/tty_pty.c:
ptcopen() can be declared in traditional C now that dev_t isn't short.
Use input buffer watermarks of TTYHOG-512 (high) and (high)*7/8
(low) instead of TTYHOG/2 (high) and TTYHOG/5 (low) to agree with
some drivers. 512 is magic and some things depended on TTYHOG/2
>= TTYHOG-512 to work; now they depend on the 512 magic not changing
and TTYHOG-512 being significantly larger than 0. This should be
handled in ttsetwater().
Separate the decision about whether to do input flow control from
doing it. ttyblock() now just starts input flow control (hardware
and/or software) and there is a new function ttyunblock() to stop
it. The decisions are the same except for the watermark changes
and allowing for input expansion for PARMRK.
When flushing input, try harder at first to send a start character
if required, but give up if the first attempt fails.
cy.c, rc.c, sio.c:
Simplify: let ttyinput() handle input flow control if it is not
being bypassed. Use ttyblock() to start flow control otherwise.
rc.c:
Use same input flow control test as elsewhere: test in a more
efficient order and start flow control at >= highwater instead of
at > highwater.
essential when I fix excessive wakeups for output-below-low-water.
In cy.c and sio.c, wake up via the driver start routine to also
eliminate duplicated code involving the clearing of TS_TTSTOP.
Always (except in code to be replaced soon) call driver start
routine directly instead of going through ttstart().
ttwwakeup(). The conditions for doing the wakeup will soon become
more complicated and I don't want them duplicated in all drivers.
It's probably not worth making ttwwakeup() a macro or an inline
function. The cost of the function call is relatively small when
there is a process to wake up. There is usually a process to wake
up for large writes and the system call overhead dwarfs the function
call overhead for small writes.
were two races:
- q_to_b() might unexpectedly return 0 (e.g, after a keyboard signal
flushes the output queue and isn't echoed). ansi_put() interprets
0 bytes as 4GB...
- more output (e.g. for echoes) might arrive afer q_to_b() returns 0.
Then scstart() returns presumably and the new output might not be
handled for a long time.
Remove unused function scxint().
Fix prototypes (foo() isn't a prototype).
syscons' output is now only about 4-5 times slower than I want.
It loses a factor of 2 for scrolling output by unnecessarily copying
the screen buffer, a factor of 4/3 for dumb OPOST processing, and
a factor of 3/2 for clist processing.
no ports are active, provided there are no polled ports and no
`LOSESOUTINTS' ports. Do a little more in the interrupt handler instead.
This is a little less efficient if there are are many active ports but
a little more efficient otherwise. Polled ports are ones with no irq
specified (as before). `LOSESOUTINTS' ports are ones with 0x08 set in
their config flags. Unless this flag is set, it will now take up to one
second to recover from lost output interrupts, if any. Some 8250s and
16450s lose output interrupts.
Improve output buffering: copy the clist buffer to 2 linear buffers if
necessary and possible instead of to 1. Handle an arbitrary queue of
buffers in the interrupt handler. Check for waking up sleepers after
copying characters out of the clist buffer instead of before.
Delay translation of TIOCM_DTR to MCR_DTR etc. so that the top level
routines are more machine independent.
Fix bogus device register in unused code.
to access it. setdelayed() actually ORs the bits in `idelayed' into
`ipending' and clears `idelayed'.
Call setdelayed() every (normal) clock tick to convert delayed
interrupts into pending ones.
Drivers can set bits in `idelayed' at any time to schedule an interrupt
at the next clock tick. This is more efficient than calling timeout().
Currently only software interrupts can be scheduled.
The ``flags 1'' in the fdc line is now only needed for owners of an
Insight tape (perhaps there aren't any? Mine is disfunctional). All
other probes are safe wrt. to the motor-control line of floppy disk
drives. Document the flag in LINT finally.
