Pass dwarf-version to cc1as.
Fix PR26999 - crashing in cc1as with any '*bsd' target.
This should fix possible crashes when using -g in combination with
-save-temps.
Replace loop with switch statement (rate2ridx())
(should be noop).
Tested with RTL8188EU / RTL8188CUS, STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D4848 (rebased)
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
bcm2835_mbox_fb_init sets configuration so SET_VIRTUAL_OFFSET should be used
instead of GET_VIRTUAL_OFFSET
Submitted by: Sylvain Garrigues <sylvain@sylvaingarrigues.com>
- Enable the commented out locking in fd_probe(). The worker thread
should not be running yet (even after these changes), but better to be
safe than sorry.
- Defer starting the worker thread until after the child drives have been
probed. The worker thread startup is moved into a fdc_start_worker()
thread that the various front ends call at the end of attach. As a
side effect this fixes a few edge cases that weren't shutting down the
worker thread if attach encountered a late failure.
- When executing the initial reset requested by attach in the worker
thread, use DELAY() instead of a tsleep() if cold is set.
Tested by: Howard Su <howard0su@gmail.com>
Sponsored by: Netflix
Eventually with earlier AP startup this code will change to call the
startup function synchronously instead of queueing the task. Moving
the time we queue the task should be a no-op since taskqueue threads
don't start executing tasks until much later, but this reduces the diff
with the earlier AP startup patches.
Sponsored by: Netflix
sys/geom/geom_disk.c:
disk_attr_changed(): Generate a devctl event of type GEOM:<attr> for
every call.
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D5952
IPv6 addresses has a scope ID which sometimes is stored in the
"sin6_scope_id" field of "struct sockaddr_in6" and sometimes as part
of the IPv6 address itself depending on the context. If the scope ID
is not in the expected location, the IPv6 address lookups in the
so-called GID table will fail. Some code factoring has been made to
achieve a clean exit of the "addr_resolve" function via a common
"done" label.
Sponsored by: Mellanox Technologies
Submitted by: Shani Michaeli <shanim@mellanox.com>
MFC after: 1 week
This also protects them from trying to create .meta files
with WITH_META_MODE.
Reported by: Nikolai Lifanov <lifanov@mail.lifanov.com>
Sponsored by: EMC / Isilon Storage Division
already required both of them, so having a separate rctl_lock didn't
buy us anything.
Reviewed by: mjg@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5914
tp->snd_wnd. This can happen, for example, when the remote side responds to
a window probe by ACKing the one byte it contains.
Differential Revision: https://reviews.freebsd.org/D5625
Reviewed by: hiren
Obtained from: Juniper Networks (earlier version)
MFC after: 2 weeks
Sponsored by: Juniper Networks
It's provided by sys.mk so there's no need to derive it from ${.CURDIR}.
Suggested by: ngie
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5998
Only compile what each SoC needs and get rid of MEDIATEK generic config.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5996
ascii.c was removed during r290494 but this introduced an issue with ASCII that
has been fixed in r290618 and lead to a rewrite of ascii.c based on none.c.
ascii.c was wrongly reintroduced in r290620 without proper svn operation which
lost the history.
Reported by: ache, danfe
ieee80211_scan_done().
Refresh comments that reference scan_next() method
(does not exist since r191746) + fix spelling of 'current'.
Differential Revision: https://reviews.freebsd.org/D5137
- Allow to enable/disable promiscuous mode when:
* interface is not a member of bridge, or;
* request was issued by user (ifconfig wlan0 promisc), or;
* interface is in MONITOR or AHDEMO mode.
- Drop local workarounds in mwl(4) and malo(4).
Tested with:
- Intel 3945BG, STA mode;
- RTL8188CUS, MONITOR mode;
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D5472
- notionally support a 'history file' flag. This doesn't do much now,
but is there to prevent scripts written against GNU units from
breaking
- correctly gracefully quit rather than exit (this will make it easier
to support a history file in the future)
- remove the "t" flag from fopen which was there to support windows. We
have not supported windows since at the latest, the introduction of
capsicum.
In Azure, the DHCP servers add private option (id 0xf5), which contains
binary form of an IPv4 address. Once this option is converted to string
form, it could contain '$', e.g.
IPv4 address: 100.72.36.54
binary form: 0x64 0x48 0x24 0x36
string form: "dH$6"
dhclient bails upon "illegal" options like the above example, thus the
VM bring-up will fail.
Also as a side note, this "illegal" option detection was added in
OpenBSD ~11years ago:
http://cvsweb.openbsd.org/cgi-bin/cvsweb/src/sbin/dhclient/dhclient.c?rev=1.50&content-type=text/x-cvsweb-markup
And it was removed along with the removal of script support in OpenBSD
~3years ago:
http://cvsweb.openbsd.org/cgi-bin/cvsweb/src/sbin/dhclient/dhclient.c?rev=1.159&content-type=text/x-cvsweb-markup
Reported by: Hongxiong Xian <v-hoxian microsoft com>
Reviewed by: jhb, Dexuan Cui <decui microsoft com>
Tested by: Hongxiong Xian <v-hoxian microsoft com>
Analyzed by: Dong Liu <doliu microsoft com>
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5853
VideoCore reports garbage in viewport geometry fields unless
viewport was set previously by earlier stage boot loader. So
when booting FreeBSD kernel directly from VideoCore's start.elf
framebuffer intialization fails due to invalid vxres, vyres
values. Make sure we request viewport to be equal to physical
resolution
Submitted by: Sylvain Garrigues <sylvain@sylvaingarrigues.com>
