numbers with Chacha20. Keep the API, though, as that is what the
other *BSD's have done.
Use the boot-time entropy stash (if present) to bootstrap the
in-kernel entropy source.
Reviewed by: delphij,rwatson
Approved by: so(delphij)
MFC after: 2 months
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D10048
is no phy-handle property, fall back to using MII_PHY_ANY.
This still doesn't support an mdio bus with multiple PHYs on it, or the
possibility that the PHY being used by this instance of ffec is on the
mdio bus of some other instance (which is now a possibility with imx6ul).
Adding that support will require changes in fdt_get_phyaddr(), which is
currently making some assumptions that don't work with modern fdt data.
The only thing this phy needs that the ukphy driver doesn't provide is
that the value in the proprietary Phy Control 2 Register must be saved
before doing a soft reset and restored afterwards. Most modern phys have
"sticky bits" for low-level config that survive a reset, but on this one
the values in all registers go back to defaults, wiping out any board-
specific config set up by the bootloader/bios/whatever.
modes if the font size is >= 14.
This is the X cursor XC_left_ptr (#68) (glyph #45 in an X cursor font).
Also found in vt. The old 9x13 cursor is the 10x16 one trimmed not very
well.
8x8 fonts need a smaller cursor instead of a larger one, except when
the pixel size is small. Text mode is still limited to width and height
1 more than the font (so the 9x13 is already 4 pixels too high for it).
access it via pointers (still to only 1 instance, now with a less
generic name).
Restructure the "and" and "or" masks as border and interior masks
(where the "and" mask was for the union of the border and the interior).
"and" and "or" were only a detail in a not very good implementation,
and after fixing that the union was only used to calculate the border
at runtime.
Use the metric data in more places to clip to active pixels earlier.
available starting with T6. The values in the timer holdoff registers
are multiplied by the scaling factor before use.
dev.<nexus>.<n>.holdoff_timers shows the final values of the
timers in microseconds.
MFC after: 1 week
Sponsored by: Chelsio Communications
This fixes some panics after disconnecting mounted disks.
Submitted by: imp (slightly different version, which I've then lost)
Reviewed by: kib, imp, mckusick
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D9674
by the shutdown(2) system call. This ability has been lost as part of the svn
revision 285910.
Reviewed by: ed, rwatson, glebius, hiren
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10351
At this point we have not rendezvous'ed with the mirror worker thread, and
I/O may still be in flight. Various I/O completion paths expect to be able
to obtain a reference to the mirror softc from the GEOM, so setting it to
NULL may result in various NULL pointer dereferences if the mirror is
stopped with -f or the kernel is shut down while a mirror is
synchronizing. The worker thread will clear the softc pointer before
exiting.
Tested by: pho
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
We are otherwise susceptible to a race with a concurrent teardown of the
mirror provider, causing the I/O to be left uncompleted after the mirror
started withering.
Tested by: pho
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
mode.
Direct mode always supported widths up to 32, except for its hard-coded
16s matching the pixmap size. Text mode is still limited to 9 its 2x2
character cell method and missing adjustments for the gap between
characters, if any.
Cursor heights can be almost anything in graphics modes.
Regular I/O requests may be blocked by concurrent synchronization requests
targeted to the same LBAs, in which case they are moved to a holding queue
until the conflicting I/O completes. We therefore want to stop
synchronization before completing pending I/O in g_mirror_destroy_provider()
since this ensures that blocked I/O requests are completed as well.
Tested by: pho
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
While the former name is easier to read, the "_flags" suffix has a special
meaning for loader(8) and, thus, it was impossible to set the knob via
loader.conf(5). The loader interpreted the setting as flags that should
be passed to a kernel module named "vfs.zfs.debug".
Discussed with: smh
MFC after: 2 weeks
much as possible, by avoiding null ANDs and ORs to the frame buffer.
Mouse cursors are fairly sparse, especially for their frame. Pixels
are written in groups of 8 in planar mode and the per-group sparseness
is not as large, but it still averages about 40% with the current
9x13 mouse cursor. The average drawing time is reduced by about this
amount (from 22 usec constant to 12.5 usec average on Haswell).
This optimization is relatively larger with larger cursors. Width 10
requires 6 frame buffer accesses per line instead of 4 if not done
sparsely, but rarely more than 4 if done sparsely.
The "cred" argument of ncl_flush() is unused and it was confusing to have
the code passing in NULL for this argument in some cases. This patch deletes
this argument.
There is no semantic change because of this patch.
MFC after: 2 weeks
mode.
Don't manually unroll the 2 inner loops. On Haswell, doing so gave a
speedup of about 0.5% (about 4 cycles per iteration out of 1400), but
hard-coded a limit of width 9 and made better better optimizations
harder to see. gcc-4.2.1 -O does the unrolling anyway, unless tricked
with a volatile hack. gcc's unrolling is not very good and gives a
a speedup of about half as much (about 2 cycles per iteration). (All
timing on i386.)
Manual unrolling was only feasible because the inner loop only iterates
once or twice. Usually twice, but a dynamic check is needed to decide,
and was not moved from the second-innermost loop manually or by gcc.
This commit basically adds another dynamic check in the inner loop.
Cursor widths of 10-17 require 3 iterations in the inner loop and this
is not so easy to unroll -- even gcc stops at 2.
The 'pktid' variable is modified while being used twice between
sequence points, probably due to htonl() is macro.
Reported by: PVS-Studio
MFC after: 1 week
to pass rule number and rule set to userland. In r272840 the kernel
internal rule representation was changed and the rulenum field of
struct ip_fw_rule got the type uint32_t, but userlevel representation
still have the type uint16_t. To not overflow the size of pointer
on the systems with 32-bit pointer size use separate variable to
copy rulenum and set.
Reported by: PVS-Studio
MFC after: 1 week
do for streaming sockets.
And do more cleanup in the sbappendaddr_locked_internal() to prevent
leak information from existing mbuf to the one, that will be possible
created later by netgraph.
Suggested by: glebius
Tested by: Irina Liakh <spell at itl ua>
MFC after: 1 week
ipfilter man pages. This also currently restricts keep frags to only when
keep state is used, which is redundant because keep state currently
assumes keep frags. This commit fixes this.
To the user this change means that to maintain the current behaviour
one must add keep frags to any ipfilter keep state rule (as documented
in the man pages).
This patch also allows the flexability to specify and use keep frags
separate from keep state, as documented in an example in ipf.conf.5,
instead of the currently broken behaviour.
Relnotes: yes
Memory is malloc'd, then a search for a match in the fragment table
is made and if the fragment matches, the wrong fragment table is
freed, causing a use after free panic. This commit fixes this.
A symptom of the problem is a kernel page fault in bcopy() called by
ipf_frag_lookup() at line 715 in ip_frag.c. Another symptom is a
kernel page fault in ipf_frag_delete() when called by ipf_frag_expire()
via ipf_slowtimer().
MFC after: 1 week
TXP_CMD_WAIT argument allocates a response buffer. If the allocation
fails, txp_ext_command() returns an error and it's handed in caller.
Found by: PVS-Studio
Some NFSv4.1 servers such as AmazonEFS can only support a small fixed number
of open_owner4s. This patch adds a mount option called "oneopenown" that
can be used for NFSv4.1 mounts to make the client do all Opens with the
same open_owner4 string. This option can only be used with NFSv4.1 and
may not work correctly when Delegations are is use.
Reported by: cperciva
Tested by: cperciva
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8988
A function called svcpool_close() was added to the server side krpc by
r313735, so that a pool could be closed without destroying the data structures.
This little patch adds a call to it for the callback pool (svcpool_nfscbd),
so that the nfscbd daemon can be killed/restarted and continue to work
correctly.
MFC after: 2 weeks
Some dummynet modules used strcpy() to copy from a larger buffer
(dn_aqm->name) to a smaller buffer (dn_extra_parms->name). It happens that
the lengths of the strings in the dn_aqm buffers were always hardcoded to be
smaller than the dn_extra_parms buffer ("CODEL", "PIE").
Use strlcpy() instead, to appease static checkers. No functional change.
Reported by: Coverity
CIDs: 1356163, 1356165
Sponsored by: Dell EMC Isilon
