the link rate - some ich motherboards overclock ac97 out of the box.
Will hopefully replace this with a callibration loop in time for 4.5R
freeze.
Problem reported by Luigi Rizzo and fix derived from his code (put
diff in ich.c rather than ac97.c).
MFC after: 3 days
superblock that is already set up to handle pointer types. This
fixes an accidental change in the superblock size on 64-bit platforms
caused by revision 1.24.
The description field is unused in -stable, so the MFC there is equivalent
to a comment. It can be done at any time, i am just setting a reminder
in 45 days when hopefully we are past 4.5-release.
MFC after: 45 days
the target thread of the join operation. This allows the cancelled
thread to detach the target thread in its cancellation handler.
This bug was found by Butenhof's cancel_subcontract test.
Reviewed by: jasone
variables. Use the -d flag in sysctl(8) to see this information.
Possible extensions to sysctl:
+ report variables that do not have a description
+ given a name, report the oid it maps to.
Note to developers: have a look at your code, there are a number of
variables which do not have a description.
Note to developers: do we want this in 4.5 ? It is a very small change
and very useful for documentation purposes.
Suggested by: Orion Hodson
"skimming thru" the printcap file looking for some common mistakes that
people make. These are the kinds of mistakes where the printcap file
probably looks correct to human eyes, but is wrong in some subtle way
which causes a problem in some queue definitions. The program treats
these as "warnings" not "errors".
Note that I'm flexible on the m.f.c. schedule, if people would rather
this waited until after 4.5-release.
Reviewed by: no screams from freebsd-audit freebsd-print@bostonradio.org
MFC after: 4 days
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
It tries to comply with the SCD 2.4.1 (and thus Sparc 64-bit psABI).
This is an amalgamation of the FreeBSD Alpha crt1.c and the BSD/OS Sparc
crt0.c (which the copyright reflects).
