in connection with Marvell based SATA->PATA dongles.
The problem was caused by a combination of things working
together to make it hard to spot...
The ATA driver has always started the ATA command, then build
the SG list for DMA and then finally started the DMA engine.
While this is according to specs, it poses a potential
problem as some controllers apparently do not allow for unlimitted
time between starting the ATA command and starting the DMA engine.
At about the same time as ATAng was committed there were lots
of other changes applied, some of which was locking in parts
that causes the busdma load functions to take significantly
longer to load the SG list.
This pushed the time spent between starting the ATA command and
starting the DMA engine over the hill for some controllers
(especially the Silicon Image DS3112a) and caused what looked
like lost interrupts.
The solution is to get all the SG list work or rather all
busdma related stuff done before we even try to start anything.
This has the nice side effect of seperating busdma out the
way it should be, so the working of the ATA machinery is not
cluttered up with busdma droppings, making the code easier
to read and understand.
was that accessing the status reg could occour too fast, confusing
the logic in the flash part. Could not have been located without:
HW donated by: Jonas Bülow <jonas@servicefactory.se>
provide no methods does not make any sense, and is not used by any
driver.
It is a pretty hard to come up with even a theoretical concept of
a device driver which would always fail open and close with ENODEV.
Change the defaults to be nullopen() and nullclose() which simply
does nothing.
Remove explicit initializations to these from the drivers which
already used them.
Fix to the messages output under CAM_DEBUG_CCB: the summary sense
information (error bits and sense key) is in the error field, not
in the result field, of struct ata_request. No other functional change.
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
For the floppy driver, use fdcontrol to manipulate density selection.
For the CD drivers, the 'a' and 'c' suffix is without actual effect and
any applications insisting on it can be satisfied with a symlink:
ln -s /dev/cd0 /dev/cd0a
Ongoing discussion may result in these pieces of code being removed before
the 5-stable branch as opposed to after.
This will get rid of the warnings issued at shutdown (that seems to
worry alot of users), but will also no flush cache on lots of
devices that can, but doesn't set the right support bits...
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
real SATA disks now that I can test it.
Add support for the SiI 3112 SATA chip using memory mapped I/O.
Update the support for the SiI 0680 to use the memio interface as well.
Sponsored by: David Leimbach <leimy2k@mac.com> (3112 based controller)
Sponsored by: FreeBSD Systems (www.FreeBSDsystems.com) (SATA disks)
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
has already been registered with ATAPI/CAM (else there is nothing
to do). atapi_cam_reinit_bus may be called before the bus is
registered if an ATAPI command times out during the boot sequence.
PR: i386/51421
Reviewed by: roberto
Approved by: re (rwatson)
MFC after: 1 week
Note: this might print failure messages on some systems, unfortunatly
the info from the device, stating if flushing is supported, cannot be trusted
so the operation is always issued on all devices, just in case...
project by providing documentation (under NDA) and hardware for
testing. This commit is the first result of the cooperation, and
adds support for several of their new controllers that we didn't
support before (and probably newer would have without this arrangement).
Add support for the Promise SATA150 TX2/TX4 and the Promise TX4000
controllers. This also adds support for various motherboard fitted
Promise SATA/ATA chips.
Note that this code uses memory mapped registers to minimize overhead.
I belive FreeBSD has made another first in the Open Source world
by being able to release support for this :)
"Ian gave me this patch" I assume this is iadowse@.
Also, pull in a few devices NetBSD's table. More are there, but I need
to properly move them to pccarddev before including them here.
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
Clean up the DMA interface too much unneeded stuff crept in with
the busdma code back when.
Modify the ATA_IN* / ATA_OUT* macros so that resource and offset
are gotten from a table. That allows for new chipsets that doesn't
nessesarily have things ordered the good old way. This also removes
the need for the wierd PC98 resource functions.
Tested on: i386, PC98, Alpha, Sparc64
- Use it in atacontrol(8) when listing ATA devices instead of
stopping at the first ENXIO received.
This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.
Reviewed by: sos
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
Retire the "d_dump_t" and use the "dumper_t" type instead.
Dumper_t takes a void * as first arg which is more general than the
dev_t taken by d_dump_t. (Remember: we could have net-dumpers if
somebody wrote us one!)
Define the convention for GEOM controlled disk devices to be that the
first argument to the dumper function is the struct disk pointer.
Change device drivers accordingly.
Change the argument to disk_destroy() to be the same struct disk * as
disk_create() takes.
This enables drivers to ignore the (now) bogus dev_t which disk_create()
returns.
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
To fix scsi, don't wait for ithreads if we're dumping, it makes the
debugger sad.
To fix ata, use what appears to be a polling method if we're dumping,
I stole this from tmm but added code to ensure that this change is
only in effect while dumping.
Tested by: des
Properly handle the newer Promise SuperSwap 1000 enclosures.
Print out what kind of enclosure was found in the probe.
Misc cleanups in the enclosure handling code.
Sponsored by: Advanis Inc.
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
the device is not actually present), clear the corresponding bit in
the ch->devices bitmap. This resolves a panic that occurred with ATAPI/CAM
after an APM suspend/resume, when the ATA hardware would erroneously
report an extra ATAPI device.
Approved by: re, sos
Reviewed by: roberto
MFC after: 7 days
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
and XPT_RESET_DEV.
In order to properly handle reset requests whether they originate in the
ATA layer (atacontrol reinit) or from the CAM layer (camcontrol reset)
ata_reinit does not cause the SIM to be deallocated anymore. The SIM
is now unconditionnally created for each ATAPI bus.
This change may cause existing bus ids to change on some setups.
Reviewed by: roberto
Approved by: sos
* Change atapi-cd ioctls to use the same units.
* Change burncd, cdcontrol to convert CDROM speed to KB/sec before
calling the ioctl. Add a "max" speed option for their command lines.
This change does not break ABI but does change the units passed through
the ioctl so 3rd party software that uses cdrio.h will have to convert
(most likely by multiplying CDROM speed by 177 to get KB/s).
PR: kern/36845
Submitted by: Philipp Mergenthaler <p@i609a.hadiko.de> (CAM ioctls)
Reviewed by: sos, ken
MFC after: 1 month
The problem is that the code does a check for the granparent of
the Promise chip, if this is a bridge of the right type, we have
a TX4 on our hands, and need to handle that ones "issues".
Now the grandparent check cause subtle bugs in the newbus system,
mainly that pci_get_devid doesn't return an error value.
This patch works around the issue by using BUS_READ_IVAR() instead.
doesn't give them enough stack to do much before blowing away the pcb.
This adds MI and MD code to allow the allocation of an alternate kstack
who's size can be speficied when calling kthread_create. Passing the
value 0 prevents the alternate kstack from being created. Note that the
ia64 MD code is missing for now, and PowerPC was only partially written
due to the pmap.c being incomplete there.
Though this patch does not modify anything to make use of the alternate
kstack, acpi and usb are good candidates.
Reviewed by: jake, peter, jhb
and predictable way, and I apologize if I have gotten it wrong anywhere,
getting prior review on a patch like this is not feasible, considering
the number of people involved and hardware availability etc.)
If struct disklabel is the messenger: kill the messenger.
Inside struct disk we had a struct disklabel which disk drivers used to
communicate certain metrics to the disklayer above (GEOM or the disk
mini-layer). This commit changes this communication to use four
explicit fields instead.
Amongst the benefits is that the fields do not get overwritten by
wrong or bogus on-disk disklabels.
Once that is clear, <sys/disk.h> which is included in the drivers
no longer need to pull <sys/disklabel.h> and <sys/diskslice.h> in,
the few places that needs them, have gotten explicit #includes for
them.
The disklabel inside struct disk is now only for internal use in
the disk mini-layer, so instead of embedding it, we malloc it as
we need it.
This concludes (modulus any mistakes) the series of disklabel related
commits.
I belive it all amounts to a NOP for all the rest of you :-)
Sponsored by: DARPA & NAI Labs.
Rename diskerr() to disk_err() for naming consistency.
Drop the by now entirely useless struct disklabel argument.
Add a flag argument for new-line termination.
Fix a couple of printf-format-casts to %j instead of %l.
Correctly print the name of all bio commands.
Move the function from subr_disklabel.c to subr_disk.c,
and from <sys/disklabel.h> to <sys/disk.h>.
Use the new disk_err() throughout, #include <sys/disk.h> as needed.
Bump __FreeBSD_version for the sake of the aac disk drivers #ifdefs.
Remove unused disklabel members of softc for aac, amr and mlx, which seem
to originally have been intended for diskerr() use, but which only rotted
and got Copy&Pasted at least two times to many.
Sponsored by: DARPA & NAI Labs.
(what we want to mask is the ATA interrupts, which run at level splbio),
and add interrupt masking around the statement that modifies the
request queue for a SIM.
This resolves problems reported by users under heavy ATAPI load.
Reviewed by: roberto
