When fixing this module to build on PC98, I actually broke the build on
ARM64. On PC98 we need to pull in the sources from the MACHINE_CPUARCH
(i386), but on ARM64 we need to use the MACHINE, as MACHINE_CPUARCH is
set to aarch64 instead of just arm64.
Sync libarchive with vendor including security fixes
Vendor issues fixed:
Issue #731: Reject tar entries >= INT64_MAX
Issue #744 (part of Issue #743): Enforce sandbox with very long pathnames
Issue #748: Zip decompression failure with highly-compressed data
Issue #767: Buffer overflow printing a filename
Issue #770: Zip read: be more careful about extra_length
MFC after: 3 days
same name as for i386). It is not reconnected yet.
Which method is better is too machine-dependent and system-dependent
to replace the old method unconditionally.
This fixes a tautological pointer comparison warning, but would also a
real bug for a platform where bus_dmamap_unload of a static allocation
is not a no-op.
Summary:
Some device trees put "fsl,ns16650" first in the compatible list. This causes
the probe code to choke, even though the device is compatible with ns16650, and
has it listed later in the tree.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7676
beyond the end of disk. r298900 added code to prevent this. Some BIOSes
cause significant delays if asked to read past end-of-disk.
We never trusted the BIOS to accurately report the sectorsize of disks
before and this set of changes. Unfortuately they interact badly with
the infamous >2TB wraparound bugs. We have a number of relatively-recent
machines in the FreeBSD.org cluster where the BIOS reports 3TB disks as 1TB.
With pre-r298900 they work just fine. After r298900 they stop working if
the boot environment attempts to access anything outside the first 1TB on
the disk. 'ZFS: I/O error, all block copies unavailable' etc. It affects
both UFS and ZFS if they try to boot from large volumes.
This change replaces the blind trust of the BIOS end-of-disk reporting
with a read-ahead clip to prevent reads crossing the of end-of-disk
boundary. Since 2^32 (2TB) size reporting truncation is not uncommon,
the clipping is done on 2TB aliases of the reported end-of-disk.
ie: a 3TB disk reported as 1TB has readahead clipped at 1TB, 3TB, 5TB, ...
as one of them is likely to be the real end-of-disk.
This should make the loader on these broken machines behave the same as
traditional pre-r298900 loader behavior, without disabling read-ahead.
PR: 212139
Discussed with: tsoome, allanjude
macro is defined in lots of different places in ipfilter, so replace all
of the nonportable definitions with portable ones.
Pointy hat to: dim
X-MFC-With: r304959, r304953
MFC after: 3 days
This will allow us to perform bhndb(4) bridge configuration based on
the identified hardware, prior to performing full enumeration of the
child bhnd bus.
Approved by: adrian (mentor, implicit)
and negative shift counts.
Fix error messages: print "Division" instead of "Divide"; print
multiplier-like, addition-like and logical operator tokens instead of
garbage (usually the command name).
ddb has a primitive lexer with excessive information hiding that makes
it hard to find even the point in the line where a syntax error is
detected. Old ddb just printed "Syntax error" and this was unimproved
in most places by printing a garbage token.
Early use of vm86 depends on the PIC being reset to mask interrupts,
but r286667 moved PIC initialization to after where vm86 may be first
used.
Move the PIC initialization up to immdiately before vm86 initialization.
All invocations of diff that I tried display this move poorly so that it
looks like PIC and vm86 initialization was moved later.
r286667 was to move console initialization later. The diffs are again
unreadable -- they show a large move that doesn't seem to involve the
console. The PIC initialization stayed just below the console
initialization where it could still be debugged but no longer works.
Later console initialization breaks mainly debugging vm86 initialization
and memory sizing using ddb and printf(). There are several printf()s
in the memory sizing that now go nowhere since message buffer
initialization has always been too late. Memory sizing is done by loader
for most users, but the lost messages for this case are even more
interesting than for an auto-probe since they tell you what the loader
found.
vm86 uses the tss, but r273995 moved tss initialization to after where
it may be first used, just because tss_esp0 now depends on later
initializations and/or amd64 does it later.
vm86 is first used for memory sizing in cases where the loader can't
figure out the size or is not used. Its initialization is placed
immediately before memory sizing to support this, and the tss was
initialized a little earlier.
Move everything in the tss initialization except for tss_esp0 back to
almost where it was, immediately before vm86 initialization (the
combined move is from before dblflt_tss initialization to after). Add
only early initialization of tss_esp0, later reloading of the tss, and
comments. The initial tss_esp0 no longer has space for the pcb since
initially the size of the pcb is not known and no pcb is needed.
(Later changes broke debugging at this point, so the nonexistent pcb
cannot be used by debuggers, and at the time of 273995 when ddb was
almost able to debug this problem it didn't need the pcb.) The
iniitial tss_esp0 still has a magic 16 bytes reserved for vm86
although I think this is unused too.
In particular, preserve syscall arguments on stack, since callee is
not required to preserve arg-passing registers. Align stack.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Since ptrace(2) syscall can return -1 for non-error situations, libc
wrappers set errno to 0 before performing the syscall, as the service
to the caller. On both i386 and amd64, the errno symbol was directly
referenced, which only works correctly in single-threaded process.
Change assembler wrappers for ptrace(2) to get current thread errno
location by calling __error(). Allow __error interposing, as
currently allowed in cerror().
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
conversions from int to short changing the values. This applies to
B38400 and higher, since their values do not fit into a short.
However, since the wrapped values are still unique, and they only serve
as keys, there is no problem in adding a cast to silence the warnings.
This also avoids changing the ABI, which would happen if we changed
NCURSES_OSPEED to int.
Discussed with: Thomas Dickey
MFC after: 1 week
are equal. Unfortunately, RFC 3484 requires that otherwise equal objects
remain in the order supplied by the DNS server. The present code attempts
to deal with this by returning -1 for objects that are equal (i.e.,
returns that the first parameter is less then the second parameter).
Unfortunately, the qsort API does not state that the first parameter
passed in is in any particular position in the list.
PR: 212122
Submitted by: Herbie.Robinson@stratus.com
MFC after: 3 days
cnv API is a set of functions for managing name/value pairs by cookie.
The cookie can be obtained by nvlist_next(), nvlist_get_parent() or
nvlist_get_pararr() function. This patch also includes unit tests.
Submitted by: Adam Starak <starak.adam@gmail.com>
