The mountpoint may not have defined an iosize parameter, so an attempt
to configure readahead on a device file can lead to a divide-by-zero
crash.
The sequential heuristic is not applied to I/O to or from device files,
and posix_fadvise(2) returns an error when v_type != VREG, so perform
the same check here.
Reported by: syzbot+e4b682208761aa5bc53a@syzkaller.appspotmail.com
Reviewed by: kib
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D21864
The debug level generally just controls verbosity of libusb for debugging
libusb devices/usage. We allow the environment to set the debug level
independent of the application, but the application will always override
this if it explicitly sets the debug level.
Changing the environment is easy, but patching the software to change the
debug level isn't necessarily easy or possible. Further, there's this
write-only debug_fixed variable that would seem to imply that the debug
level should be fixed, but it isn't currently used. Change the logic to use
strtol() so we can detect real 0 vs. conversion failure, then honor
debug_fixed in libusb_set_debug.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D21877
For ll/sc architectures, atomic(9) allows failure modes where *old == val
due to write failure and callers should compensate for this. Do not retry on
failure, just leave 0 in ret and fail the operation if we couldn't sc it.
This lets the caller determine if it should retry or not.
Reviewed by: kib
Looks ok: imp
Differential Revision: https://reviews.freebsd.org/D21836
installer when installing the system on a ZFS root filesystem.
For arm64, zfs_load="YES" does not add opensolaris.ko as a kld
dependency, so add it explicitly to prevent boot-time failures
out-of-box.
PR: 240478
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (Netgate)
The PRM suggests random 0 - 10ms to prevent multiple waiters on the same
interval in order to avoid starvation.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Linux commits:
6c780a0267b8
b8a92577f4be.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5en(4) after r348254.
The unlimited send tags are shared amount multiple connections and are
not allocated per send tag allocation request. Only increment the refcount.
MFC after: 3 days
Sponsored by: Mellanox Technologies
It may happen during link down that the running state may be observed
non-zero in the transmit routine, right before the running state is
cleared. This may end up using a destroyed mutex.
Make all channel mutexes and callouts persistant.
Preserve receive and send queue statistics during link toggle.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5core. The EEPROM information is not only a property of the
mlx5en(4) driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
The following sysctls are added:
dev.mce.N.conf.qos.cable_length
dev.mce.N.conf.qos.buffers_size
dev.mce.N.conf.qos.buffers_prio
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
All prints in mlx5core should use on of the macros:
mlx5_core_err/dbg/warn
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
In case of health counter fails to increment it indicates a bad device health.
In case when the syndrome indicated by firmware is 0x0, this indicates that
firmware is unable to respond to initialization segment reads.
Add proper print in this case.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MPFS is a logical switch in the Mellanox device which forward packets
based on a hardware driven L2 address table, to one or more physical-
or virtual- functions. The physical- or virtual- function is required
to tell the MPFS by using the MPFS firmware commands, which unicast
MAC addresses it is requesting from the physical port's traffic.
Broadcast and multicast traffic however, is copied to all listening
physical- and virtual- functions and does not need a rule in the MPFS
switching table.
Linux commit: eeb66cdb682678bfd1f02a4547e3649b38ffea7e
MFC after: 3 days
Sponsored by: Mellanox Technologies