This is the initial framework to call into the MCI HAL routines and drive
the basic state engine.
The MCI bluetooth coex model uses a command channel between wlan and
bluetooth, rather than a 2-wire or 3-wire signaling protocol to control things.
This means the wlan and bluetooth chip exchange a lot more information and
signaling, even at the per-packet level. The NICs in question can share
the input LNA and output PA on the die, so they absolutely can't stomp
on each other in a silly fashion. It also allows for the bluetooth side
to signal when profiles come and go, so the driver can take appropriate
control. There's also the possibility of dynamic bluetooth/wlan duty cycle
control which I haven't yet really played with.
It configures things up with a static "wlan wins everything" coexistence,
configures up the available 2GHz channel map for bluetooth, sets a static
duty cycle for bluetooth/wifi traffic priority and drives the basics needed to
keep the MCI HAL code happy.
It doesn't do any actual coexistence except to default to "wlan wins everything",
which at least demonstrates that things do indeed work. Bluetooth inquiry frames
still trump wifi (including beacons), so that demonstrates things really do
indeed seem to work.
Tested:
* AR9462 (WB222), STA mode + bt
* QCA9565 (WB335), STA mode + bt
TODO:
* .. the rest of coexistence. yes, bluetooth, not people. That stuff's hard.
* It doesn't do the initial BT side calibration, which requires a WLAN chip
reset. I'll fix up the reset path a bit more first before I enable that.
* The 1-ant and 2-ant configuration bits aren't being set correctly in
if_ath_btcoex.c - I'll dig into that and fix it in a subsequent commit.
* It's not enabled by default for WB222/WB225 even though I believe it now
can be - I'll chase that up in a subsequent commit.
Obtained from: Qualcomm Atheros, Linux ath9k
With r284861, UMA zones use the trash ctor and dtor by default. This is
incompatible with memguard, which frees the backing page when the item
is freed. Modify the UMA debug functions to be no-ops if the item was
allocated from memguard. This also fixes constructors such as
mb_ctor_pack(), which invokes the trash ctor in addition to performing
some initialization.
Reviewed by: glebius
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D6562
sys/cddl/contrib/opensolaris/uts/common/sys/acl.h:
Improve the english in a comment. No functional changes
Submitted by: gibbs
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
otherwise the system will hang.
This is a temporarily least intrusive crutch to get certain panicing systems
dumping. The proper fix should question is g_mirror_destroy() should be called
on a panicing system at all.
Discussed with: mav
acquire the page lock, which recurses. Avoid the recursion by reusing
the code from vm_page_remove() in a new helper
vm_page_xunbusy_maybelocked().
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
fractional floating point values with integer divides. This will
eliminate any chance that the compiler will generate code to evaluate
the expression using floating point at runtime.
Suggested by: bde
Submitted by: Rasool Al-Saadi <ralsaadi@swin.edu.au>
MFC after: 8 days (with r300779 and r300949)
comp_handler_lock but c4iw_destroy_cq has already freed the CQ memory
(which is where the lock resides).
Submitted by: Krishnamraju Eraparaju @ Chelsio
Sponsored by: Chelsio Communications
Inline version of primitives do an atomic op and if it fails they fallback to
actual primitives, which immediately retry the atomic op.
The obvious optimisation is to check if the lock is free and only then proceed
to do an atomic op.
Reviewed by: jhb, vangyzen
Do not set HWRTSEN bit when CTS-to-self is used; CTS2SELF bit triggers
CTS frame transmission by itself (and it does not work when HWRTSEN bit
is set).
Tested with:
* RTL8188CUS, HOSTAP mode (11g)
* RTL8188EU, STA mode (11g)
Receive all beacons in HOSTAP mode; they will give more information about
present non-ERP / legacy BSSs (used to choose protection mode).
Tested with RTL8188CUS (HOSTAP, urtwn) + RTL8821AU (HOSTAP, 11b mode).
This simplifies setting an initial interrupt moderation value, and
avoids most calls to evx_ev_qmoderate from contexts where MCDI is
not allowed (MCDI is need for an EVQ timer workaround in a later patch).
Submitted by: Andy Moreton <amoreton at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6673
by default. This is a workaround for a too simplistic ICL module
choosing mechanism. To use it, specify offload in ctl.conf
or iscsi.conf.
This fixes a problem where "kldload cxgbei" wedges the iSCSI stack,
if you don't have a Chelsio card installed, or the endpoints of the
iSCSI session are not reachable through addresses configured
on that interface.
Reviewed by: np@
MFC after: 1 month
specific order. VNET_SYSUNINITs however are doing exactly that.
Thus remove the VIMAGE conditional field from the domain(9) protosw
structure and replace it with VNET_SYSUNINITs.
This also allows us to change some order and to make the teardown functions
file local static.
Also convert divert(4) as it uses the same mechanism ip(4) and ip6(4) use
internally.
Slightly reshuffle the SI_SUB_* fields in kernel.h and add a new ones, e.g.,
for pfil consumers (firewalls), partially for this commit and for others
to come.
Reviewed by: gnn, tuexen (sctp), jhb (kernel.h)
Obtained from: projects/vnet
MFC after: 2 weeks
X-MFC: do not remove pr_destroy
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6652
It seems that all versions of POSIX that I could find require that
<sys/resource.h> defines id_t. Define it together with rlim_t. While
there, move these typedefs closer to the top of the header file, right
after the includes, which we do in most other header files.
These are apparently conditional on there being a shared PA/LNA, which
at least on AR9462/QCA9535 devices I have isn't a thing.
I'm .. not yet sure which devices it /is/ a thing, so I'll come back
to that.
Tested:
* QCA9565 STA + bluetooth
Obtained from: Linux ath9k
* Add extra debugging - the weights debugging is really useful to ensure
things are programmed into the wlan coexistence table. The weights are
what traffic priority each of the various modes get (tx, tx-high-priority,
rx-beacon, etc) if they're all zero, things work very poorly.
* Add in coex init routines from ath9k for AR9462 and QCA9565 1ANT and 2ANT.
This control things like beacon stomping, ACK handling, antennas, PA/LNA
shared, etc.
* Some ancillary bits.
TODO:
* There's some conditional stuff around MCI_ANT_ARCH_PA_LNA_SHARED() in ath9k
which doesn't always enable force-on LNA. That'll have to be examined
and merged in as appropriate.
Obtained from: linux ath9k
Notably, this also sets AR_BTCOEX_WL_LNADIV to FORCE_ON, so LNA diversity
is always enabled and under control of the wifi chip.
Tested:
* QCA9565, STA + bluetooth mode
Obtained from: Linux ath9k
This configures the LNA antenna diversity control, which should be on
if wlan owns the LNA for bluetooth coexistence. Otherwise, make sure
it's off.
I think this is eventually intended to allow 1-antenna bluetooth +
wifi setups for QCA9565, but I'm not sure where that's actually configured
in ath9k.
Obtained from: Linux ath9k
Adding .META to targets-to-build will ensure that they will rebuild if there
is no .meta file.
Adding it to all SUFFIXES and objects ensures that at least objects will
rebuild if there is no .meta file.
This will be reverted if bmake's behavior changes to rebuild on missing .meta
files.
Sponsored by: EMC / Isilon Storage Division
- This header file has always depended on pthread_t, pthread_attr_t,
struct timespec, size_t and uid_t. Only as of POSIX 2008, these
dependencies have been states explicitly. They should now be defined.
- In our implementation, struct sigevent::sigev_notify_attributes has
type "void *" instead of "pthread_attr_t *". My guess is that this was
done to prevent pulling in the pthread types, but this can easily be
avoided by using the underlying structure types.
a non-zero ID. To do this we increment the cpuid of any CPUs with a smaller
devicetree ID by one to stop them conflicting with the boot CPU.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
