It is about 2.5 microseconds or roughly 3 times faster to use this
"PIIX" timecounter than the "i8254" timecounter. Resolution is
also 3 times better.
The code cheats and don't register the PCI device, because other pieces
of code want to use it too.
Originally spotted by: msmith
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
discussed on current.
The following variables are defined (for now):
osname (defaults to "Linux")
Allow users to change the name of the OS as returned by uname(2),
specially added for all those Linux Netscape users and statistics
maniacs :-) We now have what we all wanted!
osrelease (defaults to "2.2.5")
Allow users to change the version of the OS as returned by uname(2).
Since -current supports glibc2.1 now, change the default to 2.2.5
(was 2.0.36).
oss_version (defaults to 198144 [0x030600])
This one will be used by the OSS_GETVERSION ioctl (PR 12917) which I
can commit now that we have the MIB. The default version number is the
lowest version possible with the current 'encoding'.
A note about imprisoned processes (see jail(2)):
These variables are copy-on-write (as suggested by phk). This means that
imprisoned processes will use the system wide value unless it is written/set
by the process. From that moment on, a copy local to the prison will be
used.
A note about the implementation:
I choose to add a single pointer to struct prison, because I didn't like the
idea of changing struct prison every time I come up with a new variable. As
a side effect, the extra storage is only needed when a variable is set from
within the prison. This also minimizes kernel bloat when the Linuxulator is
not used; both compiled in or as a module.
Reviewed by: bde (first version only) and phk
that are linked into the kernel. The KLD compilation options are
changed to call these functions, rather than in-lining the
atomic operations.
This approach makes atomic operations from KLDs significantly
faster on UP systems (though somewhat slower on SMP systems).
PR: i386/13111
Submitted by: peter.jeremy@alcatel.com.au
- Add support for calling 32-bit code in other segments
- Add support for calling 16-bit protected mode code
Update APM to use this facility.
Submitted by: jlemon
On the VAX, it used to be used for special compilation to avoid the
optimizer which would mess with memory mapped devices etc. These days
we use 'volatile'.
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
This is tested, but I really can't say whether it works entirely. I
don't know exactly what to look for when testing it. So let's say this
is open for testing. Send any results to green@FreeBSD.org
Reviewed by: msmith (long ago)
config kernel mumble mumble
line has been obsoleted and removed and with it went all knowledge of
devices on the part of config.
You can still configure a root device (which is used if you give
the "-r" flag) but now with an option:
options ROOTDEVNAME=\"da0s2e\"
The string is parsed by the same code as at the "boot -a" prompt.
At the same time, make the "boot -a" prompt both more able and more
informative.
ALPHA/PC98 people: You will have to adapt a few simple changes
(defining rootdev and dumpdev somewhere else) before config works
for you again, sorry, but it's all in the name of progress.
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
only worked for configurations with "swap on generic".
usr.sbin/config/config.y:
- ignore all "swap [on] device ...' specifications except for
warning about them. They haven't done anything related to swap
for almost 4 years, and were previously silently ignored,
except for "swap on generic" which stopped swap${KERNEL}.c
from being generated. Code to support swapping is now deader
than before.
usr.sbin/config/mkswapconf.c:
- don't generate a dummy setconf() function in swap${KERNEL}.c.
sys/i386/conf/files.i386:
- swapgeneric.c is now standard. It should be merged into autoconf.c
so that it doesn't conflict with swap${KERNEL}.c for kernels named
"generic".
sys/i386/i386/autoconf.c:
- don't call setroot() for mfs roots. Since setroot() doesn't do anything
harmful, this was just a waste of time, except possibly for booting with
-a it may have helped prevent an undesireable call to setconf() by
finding a bogus rootdev.
- honor -a for ffs roots. -a now overrides all other ways of specifying
the root device. Previously, -r had precedence over -a, and the -a
handling was usually a no-op.
- don't honor -a for non-ffs roots, since it would currently just get in
the way of a clean panic.
sys/i386/i386/swapgeneric.c:
- don't declare things that are now always declared in swap${KERNEL}.c.
Don't decide things that are now decided in autoconf.c. Code to
support the "generic" case is now dead instead of useless.
perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
This is for various Olicom cards. An IBM driver is following.
This patch also adds support to tcpdump to decode packets on tokenring.
Congratulations to the proud father.. (below)
Submitted by: Larry Lile <lile@stdio.com>
- Bring down the splash screen when a vty is opened for the first
time.
- Make sure the splash screen/screen saver is stopped before
switching vtys.
- Read and save initial values in the BIOS data area early.
VESA BIOS may change BIOS data values when switching modes.
- Fix missing '&' operator.
- Move ISA specific part of driver initialization to syscons_isa.c.
atkbd
- kbdtables.h is now in /sys/dev/kbd.
all
- Adjust for forthcoming alpha port. Submitted by: dfr
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
ISDN4BSD is the work of our brand-new comitter: Hellmuth Michaelis,
who has done a tremendous amount of work to bring us this far.
There are still some outstanding issues and files to bring into
the tree, and for now it will be needed to pick up all the extra
docs from the isdn4bsd release.
It is probably also a very good idea to subscribe to the isdn@freebsd.org
mailing list before you try this out.
These files correspond to release "beta Version 0.70.00 / December
1998" from Hellmuth.
Kazu writes:
The VESA support code requires vm86 support. Make sure your kernel
configuration file has the following line.
options "VM86"
If you want to statically link the VESA support code to the kernel,
add the following option to the kernel configuration file.
options "VESA"
The vidcontrol command now accepts the following video mode names:
VESA_132x25, VESA_132x43, VESA_132x50, VESA_132x60, VESA_800x600
The VESA_800x600 mode is a raster display mode. The 80x25 text will
be displayed on the 800x600 screen. Useful for some laptop computers.
vidcontrol accepts the new `-i <info>' option, where <info> must be
either `adapter' or `mode'. When the `-i adapter' option is given,
vidcontrol will print basic information (not much) on the video
adapter. When the `-i mode' option is specified, vidcontrol will
list video modes which are actually supported by the video adapter.
Submitted by: Kazutaka YOKOTA yokota@FreeBSD.ORG
This code will be turned on with the TWO options
DEVFS and SLICE. (see LINT)
Two labels PRE_DEVFS_SLICE and POST_DEVFS_SLICE will deliniate these changes.
/dev will be automatically mounted by init (thanks phk)
on bootup. See /sys/dev/slice/slice.4 for more info.
All code should act the same without these options enabled.
Mike Smith, Poul Henning Kamp, Soeren, and a few dozen others
This code does not support the following:
bad144 handling.
Persistance. (My head is still hurting from the last time we discussed this)
ATAPI flopies are not handled by the SLICE code yet.
When this code is running, all major numbers are arbitrary and COULD
be dynamically assigned. (this is not done, for POLA only)
Minor numbers for disk slices ARE arbitray and dynamically assigned.
Highlights:
* Simple model for underlying hardware.
* Hardware basis for timekeeping can be changed on the fly.
* Only one hardware clock responsible for TOD keeping.
* Provides a real nanotime() function.
* Time granularity: .232E-18 seconds.
* Frequency granularity: .238E-12 s/s
* Frequency adjustment is continuous in time.
* Less overhead for frequency adjustment.
* Improves xntpd performance.
Reviewed by: bde, bde, bde
This is Junichi's v1.0 driver.
NOTE: Major device numbers have been changed to avoid conflict with other
FreeBSD 3.0 devices. The new numbers should be considered "official."
This driver is still considered "beta" quality, although we have been
playing with it. Please submit bugs to junichi and myself.
Submitted by: junichi@astec.co.jp
original BSD code. The association between the vnode and the vm_object
no longer includes reference counts. The major difference is that
vm_object's are no longer freed gratuitiously from the vnode, and so
once an object is created for the vnode, it will last as long as the
vnode does.
When a vnode object reference count is incremented, then the underlying
vnode reference count is incremented also. The two "objects" are now
more intimately related, and so the interactions are now much less
complex.
When vnodes are now normally placed onto the free queue with an object still
attached. The rundown of the object happens at vnode rundown time, and
happens with exactly the same filesystem semantics of the original VFS
code. There is absolutely no need for vnode_pager_uncache and other
travesties like that anymore.
A side-effect of these changes is that SMP locking should be much simpler,
the I/O copyin/copyout optimizations work, NFS should be more ponderable,
and further work on layered filesystems should be less frustrating, because
of the totally coherent management of the vnode objects and vnodes.
Please be careful with your system while running this code, but I would
greatly appreciate feedback as soon a reasonably possible.
(mutant) Crystal CSS4236 chip on the Intel PR440FX SMP motherboard.
XXX this uses some rather ugly PnP bootstrap code that is *NOT* compatable
with 'controller pnp0' or *ANY* other PnP devices. If you use some other
PnP devices, enabling css0 will burn your house down. :-] The
"simplified" PnP init sequence directly blats your config(8) settings onto
the chip. I'm pretty sure 'css0' will conflict with 'mss0', this whole
area desperately needs a cleanup.
I have been using the following with some success on the PR440FX:
controller snd0
device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 vector adintr
device opl0 at isa? port 0x388
device mpu0 at isa? port 0x330 irq 10 vector mpuintr
Here are the remanding changes required to support the Ensoniq
Soundscape using FreeBSD 3.0-current.
Notes:
1) ad1848_init already has code to detect if DMA_DUPLEX should
be set so it is not necessary (and is in fact a mistake) to
hard code setting it. Not all soundcards (i.e. the current
sscape driver) are capable of using DMA_DUPLEX.
2) The other changes are hopefully self explanatory. Feel free
to let me know if you need additional information.
Submitted by: john@feith.com (John Wehle)
files.i386.
We aren't sure if this new code and the old sound code will co-exist in a
kernel, so the device pcm0 line is left commented out in LINT.
Submitted-by: Luigi Rizzo
I changed a few bits here and there, mainly renaming wd82371.c
to ide_pci.c now that it's supposed to handle different chipsets.
It runs on my P6 natoma board with two Maxtor drives, and also
on a Fujitsu machine I have at work with an Opti chipset and
a Quantum drive.
Submitted by:cgull@smoke.marlboro.vt.us <John Hood>
Original readme:
*** WARNING ***
This code has so far been tested on exactly one motherboard with two
identical drives known for their good DMA support.
This code, in the right circumstances, could corrupt data subtly,
silently, and invisibly, in much the same way that older PCI IDE
controllers do. It's ALPHA-quality code; there's one or two major
gaps in my understanding of PCI IDE still. Don't use this code on any
system with data that you care about; it's only good for hack boxes.
Expect that any data may be silently and randomly corrupted at any
moment. It's a disk driver. It has bugs. Disk drivers with bugs
munch data. It's a fact of life.
I also *STRONGLY* recommend getting a copy of your chipset's manual
and the ATA-2 or ATA-3 spec and making sure that timing modes on your
disk drives and IDE controller are being setup correctly by the BIOS--
because the driver makes only the lamest of attempts to do this just
now.
*** END WARNING ***
that said, i happen to think the code is working pretty well...
WHAT IT DOES:
this code adds support to the wd driver for bus mastering PCI IDE
controllers that follow the SFF-8038 standard. (all the bus mastering
PCI IDE controllers i've seen so far do follow this standard.) it
should provide busmastering on nearly any current P5 or P6 chipset,
specifically including any Intel chipset using one of the PIIX south
bridges-- this includes the '430FX, '430VX, '430HX, '430TX, '440LX,
and (i think) the Orion '450GX chipsets. specific support is also
included for the VIA Apollo VP-1 chipset, as it appears in the
relabeled "HXPro" incarnation seen on cheap US$70 taiwanese
motherboards (that's what's in my development machine). it works out
of the box on controllers that do DMA mode2; if my understanding is
correct, it'll probably work on Ultra-DMA33 controllers as well.
it'll probably work on busmastering IDE controllers in PCI slots, too,
but this is an area i am less sure about.
it cuts CPU usage considerably and improves drive performance
slightly. usable numbers are difficult to come by with existing
benchmark tools, but experimentation on my K5-P90 system, with VIA
VP-1 chipset and Quantum Fireball 1080 drives, shows that disk i/o on
raw partitions imposes perhaps 5% cpu load. cpu load during
filesystem i/o drops a lot, from near 100% to anywhere between 30% and
70%. (the improvement may not be as large on an Intel chipset; from
what i can tell, the VIA VP-1 may not be very efficient with PCI I/O.)
disk performance improves by 5% or 10% with these drives.
real, visible, end-user performance improvement on a single user
machine is about nil. :) a kernel compile was sped up by a whole three
seconds. it *does* feel a bit better-behaved when the system is
swapping heavily, but a better disk driver is not the fix for *that*
problem.
THE CODE:
this code is a patch to wd.c and wd82371.c, and associated header
files. it should be considered alpha code; more work needs to be
done.
wd.c has fairly clean patches to add calls to busmaster code, as
implemented in wd82371.c and potentially elsewhere (one could imagine,
say, a Mac having a different DMA controller).
wd82371.c has been considerably reworked: the wddma interface that it
presents has been changed (expect more changes), many bugs have been
fixed, a new internal interface has been added for supporting
different chipsets, and the PCI probe has been considerably extended.
the interface between wd82371.c and wd.c is still fairly clean, but
i'm not sure it's in the right place. there's a mess of issues around
ATA/ATAPI that need to be sorted out, including ATAPI support, CD-ROM
support, tape support, LS-120/Zip support, SFF-8038i DMA, UltraDMA,
PCI IDE controllers, bus probes, buggy controllers, controller timing
setup, drive timing setup, world peace and kitchen sinks. whatever
happens with all this and however it gets partitioned, it is fairly
clear that wd.c needs some significant rework-- probably a complete
rewrite.
timing setup on disk controllers is something i've entirely punted on.
on my development machine, it appears that the BIOS does at least some
of the necessary timing setup. i chose to restrict operation to
drives that are already configured for Mode4 PIO and Mode2 multiword
DMA, since the timing is essentially the same and many if not most
chipsets use the same control registers for DMA and PIO timing.
does anybody *know* whether BIOSes are required to do timing setup for
DMA modes on drives under their care?
error recovery is probably weak. early on in development, i was
getting drive errors induced by bugs in the driver; i used these to
flush out the worst of the bugs in the driver's error handling, but
problems may remain. i haven't got a drive with bad sectors i can
watch the driver flail on.
complaints about how wd82371.c has been reindented will be ignored
until the FreeBSD project has a real style policy, there is a
mechanism for individual authors to match it (indent flags or an emacs
c-mode or whatever), and it is enforced. if i'm going to use a source
style i don't like, it would help if i could figure out what it *is*
(style(9) is about half of a policy), and a way to reasonably
duplicate it. i ended up wasting a while trying to figure out what
the right thing to do was before deciding reformatting the whole thing
was the worst possible thing to do, except for all the other
possibilities.
i have maintained wd.c's indentation; that was not too hard,
fortunately.
TO INSTALL:
my dev box is freebsd 2.2.2 release. fortunately, wd.c is a living
fossil, and has diverged very little recently. included in this
tarball is a patch file, 'otherdiffs', for all files except wd82371.c,
my edited wd82371.c, a patch file, 'wd82371.c-diff-exact', against the
2.2.2 dist of 82371.c, and another patch file,
'wd82371.c-diff-whitespace', generated with diff -b (ignore
whitespace). most of you not using 2.2.2 will probably have to use
this last patchfile with 'patch --ignore-whitespace'. apply from the
kernel source tree root. as far as i can tell, this should apply
cleanly on anything from -current back to 2.2.2 and probably back to
2.2.0. you, the kernel hacker, can figure out what to do from here.
if you need more specific directions, you probably should not be
experimenting with this code yet.
to enable DMA support, set flag 0x2000 for that drive in your config
file or in userconfig, as you would the 32-bit-PIO flag. the driver
will then turn on DMA support if your drive and controller pass its
tests. it's a bit picky, probably. on discovering DMA mode failures
or disk errors or transfers that the DMA controller can't deal with,
the driver will fall back to PIO, so it is wise to setup the flags as
if PIO were still important.
'controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0xa0ffa0ff
vector wdintr' should work with nearly any PCI IDE controller.
i would *strongly* suggest booting single-user at first, and thrashing
the drive a bit while it's still mounted read-only. this should be
fairly safe, even if the driver goes completely out to lunch. it
might save you a reinstall.
one way to tell whether the driver is really using DMA is to check the
interrupt count during disk i/o with vmstat; DMA mode will add an
extremely low number of interrupts, as compared to even multi-sector
PIO.
boot -v will give you a copious register dump of timing-related info
on Intel and VIAtech chipsets, as well as PIO/DMA mode information on
all hard drives. refer to your ATA and chipset documentation to
interpret these.
WHAT I'D LIKE FROM YOU and THINGS TO TEST:
reports. success reports, failure reports, any kind of reports. :)
send them to cgull+ide@smoke.marlboro.vt.us.
i'd also like to see the kernel messages from various BIOSes (boot -v;
dmesg), along with info on the motherboard and BIOS on that machine.
i'm especially interested in reports on how this code works on the
various Intel chipsets, and whether the register dump works
correctly. i'm also interested in hearing about other chipsets.
i'm especially interested in hearing success/failure reports for PCI
IDE controllers on cards, such as CMD's or Promise's new busmastering
IDE controllers.
UltraDMA-33 reports.
interoperation with ATAPI peripherals-- FreeBSD doesn't work with my
old Hitachi IDE CDROM, so i can't tell if I've broken anything. :)
i'd especially like to hear how the drive copes in DMA operation on
drives with bad sectors. i haven't been able to find any such yet.
success/failure reports on older IDE drives with early support for DMA
modes-- those introduced between 1.5 and 3 years ago, typically
ranging from perhaps 400MB to 1.6GB.
failure reports on operation with more than one drive would be
appreciated. the driver was developed with two drives on one
controller, the worst-case situation, and has been tested with one
drive on each controller, but you never know...
any reports of messages from the driver during normal operation,
especially "reverting to PIO mode", or "dmaverify odd vaddr or length"
(the DMA controller is strongly halfword oriented, and i'm curious to
know if any FreeBSD usage actually needs misaligned transfers).
performance reports. beware that bonnie's CPU usage reporting is
useless for IDE drives; the best test i've found has been to run a
program that runs a spin loop at an idle priority and reports how many
iterations it manages, and even that sometimes produces numbers i
don't believe. performance reports of multi-drive operation are
especially interesting; my system cannot sustain full throughput on
two drives on separate controllers, but that may just be a lame
motherboard.
THINGS I'M STILL MISSING CLUE ON:
* who's responsible for configuring DMA timing modes on IDE drives?
the BIOS or the driver?
* is there a spec for dealing with Ultra-DMA extensions?
* are there any chipsets or with bugs relating to DMA transfer that
should be blacklisted?
* are there any ATA interfaces that use some other kind of DMA
controller in conjunction with standard ATA protocol?
FINAL NOTE:
after having looked at the ATA-3 spec, all i can say is, "it's ugly".
*especially* electrically. the IDE bus is best modeled as an
unterminated transmission line, these days.
for maximum reliability, keep your IDE cables as short as possible and
as few as possible. from what i can tell, most current chipsets have
both IDE ports wired into a single buss, to a greater or lesser
degree. using two cables means you double the length of this bus.
SCSI may have its warts, but at least the basic analog design of the
bus is still somewhat reasonable. IDE passed beyond the veil two
years ago.
--John Hood, cgull@smoke.marlboro.vt.us
fix stopped it being used in all cases, because substitution on unset
variables does not work.
When profiling, put -malign-functions=4 in CFLAGS instead of in PROF.
This fixes the histogram counts for profiling support functions. It
gives bogus but harmless extra alignment for genassym etc.
is incompatible with -pg. (We use a different version of mcount for
profiling frame-pointer-less assembler functions, but gcc doesn't know
about this.)
Added a missing dependency.
Cleaned up trailing backslashes.
Added comment about config's limitations/bugs handling dependencies and
backslashe/newlines.
Finished removing support for isdn drivers.
There are various options documented in i386/conf/LINT, there is more to
come over the next few days.
The kernel should run pretty much "as before" without the options to
activate SMP mode.
There are a handful of known "loose ends" that need to be fixed, but
have been put off since the SMP kernel is in a moderately good condition
at the moment.
This commit is the result of the tinkering and testing over the last 14
months by many people. A special thanks to Steve Passe for implementing
the APIC code!
supports All Cyrix CPUs, IBM Blue Lightning CPU and NexGen (now AMD)
Nx586 CPU, and initialize special registers of Cyrix CPU and msr of
IBM Blue Lightning CPU.
If revision of Cyrix 6x86 CPU < 2.7, CPU cache is enabled in
write-through mode. This can be disabled by kernel configuration
options.
Reviewed by: Bruce Evans <bde@freebsd.org> and
Jordan K. Hubbard <jkh@freebsd.org>
to -current.
Thanks goes to Ulrike Nitzsche <ulrike@ifw-dresden.de> for giving me
a chance to test this. Only the PCI driver is tested though.
One final patch will follow in a separate commit. This is so that
everything up to here can be dragged into 2.2, if we decide so.
Reviewed by: joerg
Submitted by: Matt Thomas <matt@3am-software.com>
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
uses /usr/include/sys/*, which may point to a different build tree. I'm
not sure that this is necessary, but there was a question mark over what
/usr/include/sys points to when building the "user mode" binaries in the
kernel code, especially when building the smp tree.
I suspect that the "right" line here is to use ${INCLUDES}, but that
causes warnings about unused static inline functions in stdio.h and ctype.h
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, nao@tom-yam.or.jp (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly nao@tom-yam.or.jp (HAMADA Naoki)
Obtained from:partly OpenBSD
- use a more accurate and more efficient method of compensating for
overheads. The old method counted too much time against leaf
functions.
- normally use the Pentium timestamp counter if available.
On Pentiums, the times are now accurate to within a couple of cpu
clock cycles per function call in the (unlikely) event that there
are no cache misses in or caused by the profiling code.
- optionally use an arbitrary Pentium event counter if available.
- optionally regress to using the i8254 counter.
- scaled the i8254 counter by a factor of 128. Now the i8254 counters
overflow slightly faster than the TSC counters for a 150MHz Pentium :-)
(after about 16 seconds). This is to avoid fractional overheads.
files.i386:
permon.c temporarily has to be classified as a profiling-routine
because a couple of functions in it may be called from profiling code.
options.i386:
- I586_CTR_GUPROF is currently unused (oops).
- I586_PMC_GUPROF should be something like 0x70000 to enable (but not
use unless prof_machdep.c is changed) support for Pentium event
counters. 7 is a control mode and the counter number 0 is somewhere
in the 0000 bits (see perfmon.h for the encoding).
profile.h:
- added declarations.
- cleaned up separation of user mode declarations.
prof_machdep.c:
Mostly clock-select changes. The default clock can be changed by
editing kmem. There should be a sysctl for this.
subr_prof.c:
- added copyright.
- calibrate overheads for the new method.
- documented new method.
- fixed races and and machine dependencies in start/stop code.
mcount.c:
Use the new overhead compensation method.
gmon.h:
- changed GPROF4 counter type from unsigned to int. Oops, this should
be machine-dependent and/or int32_t.
- reorganized overhead counters.
Submitted by: Pentium event counter changes mostly by wollman
type identification code out of machdep.c and into a new file of its
own. Hopefully other grot can be moved out of machdep.c as well
(by other people) into more descriptively-named files.
based on the HD64570 chip. Both the 1 and 2 port cards is supported.
Line speeds of up to 2Mbps is possible. At this speed about 95% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the X.21 interface is tested. The others may need
tweaks to the clock selection code.
(This code is as yet untested; to come after man page is written.)
This also adds inlines to cpufunc.h for the RDTSC, RDMSR, WRMSR, and RDPMC
instructions. The user-mode interface is via a subdevice of mem.c;
there is also a kernel-size interface which might be used to aid
profiling.
netscape-2.0 for Linux running all the Java stuff. The scrollbars are now
working, at least on my machine. (whew! :-)
I'm uncomfortable with the size of this commit, but it's too
inter-dependant to easily seperate out.
The main changes:
COMPAT_LINUX is *GONE*. Most of the code has been moved out of the i386
machine dependent section into the linux emulator itself. The int 0x80
syscall code was almost identical to the lcall 7,0 code and a minor tweak
allows them to both be used with the same C code. All kernels can now
just modload the lkm and it'll DTRT without having to rebuild the kernel
first. Like IBCS2, you can statically compile it in with "options LINUX".
A pile of new syscalls implemented, including getdents(), llseek(),
readv(), writev(), msync(), personality(). The Linux-ELF libraries want
to use some of these.
linux_select() now obeys Linux semantics, ie: returns the time remaining
of the timeout value rather than leaving it the original value.
Quite a few bugs removed, including incorrect arguments being used in
syscalls.. eg: mixups between passing the sigset as an int, vs passing
it as a pointer and doing a copyin(), missing return values, unhandled
cases, SIOC* ioctls, etc.
The build for the code has changed. i386/conf/files now knows how
to build linux_genassym and generate linux_assym.h on the fly.
Supporting changes elsewhere in the kernel:
The user-mode signal trampoline has moved from the U area to immediately
below the top of the stack (below PS_STRINGS). This allows the different
binary emulations to have their own signal trampoline code (which gets rid
of the hardwired syscall 103 (sigreturn on BSD, syslog on Linux)) and so
that the emulator can provide the exact "struct sigcontext *" argument to
the program's signal handlers.
The sigstack's "ss_flags" now uses SS_DISABLE and SS_ONSTACK flags, which
have the same values as the re-used SA_DISABLE and SA_ONSTACK which are
intended for sigaction only. This enables the support of a SA_RESETHAND
flag to sigaction to implement the gross SYSV and Linux SA_ONESHOT signal
semantics where the signal handler is reset when it's triggered.
makesyscalls.sh no longer appends the struct sysentvec on the end of the
generated init_sysent.c code. It's a lot saner to have it in a seperate
file rather than trying to update the structure inside the awk script. :-)
At exec time, the dozen bytes or so of signal trampoline code are copied
to the top of the user's stack, rather than obtaining the trampoline code
the old way by getting a clone of the parent's user area. This allows
Linux and native binaries to freely exec each other without getting
trampolines mixed up.
- split driver into FreeBSD specific and camera specific portions
(qcamio.c can run in user mode, with a Linux "driver top" etc,
and qcam.c should be trivial to port to NetBSD and BSDI.)
- support for 4bppand bidirectional transfers working better
- start of interleaved data-transfers byte-stream decodes (some of this
stuff has been pulled out for the moment to make it easier to debug)
At this point, anyone who wants to port it to other platforms should feel
free to do so. Please feed changes directly back to me so that I can produce
a unified distribution.
chipset. This does not attempt to do anything special with the timing
on the hope that the BIOS will have done the right thing already. The
actual interface from the wd driver to the new facility is not
implemented yet (this commit being an attempt at prodding someone else
to do it because looking at the wd driver always confuses the h*** out of me).
looking at a high resolution clock for each of the following events:
function call, function return, interrupt entry, interrupt exit,
and interesting branches. The differences between the times of
these events are added at appropriate places in a ordinary histogram
(as if very fast statistical profiling sampled the pc at those
places) so that ordinary gprof can be used to analyze the times.
gmon.h:
Histogram counters need to be 4 bytes for microsecond resolutions.
They will need to be larger for the 586 clock.
The comments were vax-centric and wrong even on vaxes. Does anyone
disagree?
gprof4.c:
The standard gprof should support counters of all integral sizes
and the size of the counter should be in the gmon header. This
hack will do until then. (Use gprof4 -u to examine the results
of non-statistical profiling.)
config/*:
Non-statistical profiling is configured with `config -pp'.
`config -p' still gives ordinary profiling.
kgmon/*:
Non-statistical profiling is enabled with `kgmon -B'. `kgmon -b'
still enables ordinary profiling (and distables non-statistical
profiling) if non-statistical profiling is configured.
libkern.a are now specified by listing their source files in
files.${MACHINE}. The list is machine-dependent to save space.
All the necessary object for each machine must be linked into the
kernel in case an lkm wants one.
redistribute a few last routines to beter places and shoot the file
I haven't act actually 'deleted' the file yet togive people time
to
have done a config.. I.e. they are likely to have done one in a week or so
so I'll remove it then..
it's now empty.
makes the question of a USL copyright rather moot.
LINT: add a couple of new/missing/undocumented options
files.i386: add linux code so that you can compile a kernel with static
linux emulation ("options LINUX")
i386/*: use #if defined(COMPAT_LINUX) || defined(LINUX) to enable static
support of linux emulation (just like "IBCS2" makes ibcs2 static)
The main thing this is going to make obvious, is that the LINUX code
(when compiled from LINT) has a lot of warnings, some of which dont look
too pleasant..
allow one EISA/ISA/PCI/VL Buslogic controller to be probed. The driver
is almost fully dynamic. It just needs some kdc work and for the SCSI code
to stop passing unit numbers up in the scsi_xfer struct.
introduced.
Fixed the device-driverness of atapi.c and spkr.c.
These changes are actually no-ops because ${DRIVER_C} is the same as
${NORMAL_C} for the i386. I could do without magic CFLAGS. Special
handling should be in the sources if possible.
This code will only be included in your kernel if you have
'options DEVRANDOM', but that will fall away in a couple of days.
Obtained from: Theodore Ts'o, Linux
had a 2.1 tag, thus sending these two changes into the 2.1 branch instead
of -current. Argh. I may bring these changes into the 2.1 anyway (they're
benign there) so I'm not going to admin them out of 2.1 for the time
being.
new driver code, there are diffs to several other existing files
on the system and a man page.
This version of matcd implements the rest of the key ioctls related to
playing audio CDs and reading table of contents information from any
type of disc.
This update also corrects several problems detected since the original
version 1(10) was released. These include:
1. Jordons report on the kernel -c string problem.
2. A problem with the driver being confused by other types of
devices located at addresses it probes.
3. An old CD TOC wouldn't always be cleared after a disc change.
4. Cleaned up code so -Wall yields no warnings on 2.0 and later.
5. A problem with drive getting out of sync with the driver when
changing between CD-Data and CD-DA.
There have only been two reports from the field relating to problems
so either the first release isn't really being used or doesn't have
many problems.
If there are any problems with this submission, please let me know.
Submitted by: Frank Durda IV <uhclem%nemesis@fw.ast.com>
card. This is the braindamaged card with the 80186 CPU on it. It is
slow, probably not very good after all, but hey, if you have one lying
around doing nothing anyway...
Added the "zp0" driver to GENERIC.
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
Submitted by: wolf (Wolfgang Stanglmeier)
Most PCI specific files moved from sys/i386/pci to sys/pci.
One PC specific file (pcibus.c) new in sys/i386/isa.
Handles at least Trantor T130 and ProAudioSpectrum adapters.
The pas driver has consequently been removed.
This driver can be configured without without interrupts.
Manpage to follow when PAS16 has been edited in.
Reviewed by: phk
Submitted by: Serge Vakulenko, <vak@cronyx.ru>
Go to a single dependancy in files.i386. Using a .c file for the
sequencer code won't work since I need to know the size of the program,
so we just include the generated .h file as:
"../../sys/gnu/misc/aic7770/aic7770_seq.h"
Reviewed by:
Submitted by:
Obtained from:
instead. The entire scheme just doesn't work as envisioned (hint: think
about make depend as well as all). Those extremely rare individuals who
actually hack on the sequencer code will know how to keep stuff in sync,
I *do* get the feeling!
of config so YOU MUST RECOMPILE CONFIG. Modifying config was the cleanest
solution to integrating this driver into the tree which will become more
obvious in the next commit.
created by Amancio Hasty (specificly, this, in conjunction with his sound
driver mods for dual-mode DMA will allow VAT compiled for BSD/386 1.1 to
run under FreeBSD 2.x.)
will do most of the work for handling them. Only one extra flag and one
bogus dependency was used for machdep.c and there was never anything
special about the others.
Add locore.s, but commented out. It's still special.
Remove com.c and lpa.c.
This is the slowest and most stupid of our SCSI-drivers, but it is there
and it works. It has been tested with CD-ROM and disk.
It uses no interrupts, no DMA, just polled I/0.
Transfer-rate is <= 100Kbyte/sec.
If you set the jumpers on the board, you can change the unit-number and
you will be able to have four of these co-exist in one computer, why one
would do that is somewhat unclear though.
If I ever get my hand on the docs for this, I will improve it of course,
but for now we can install and access those CD-ROMs.
This driver supports all the DEC EtherWORKS III NICs (DE203, DE204,
and DE205) and the later DEC EtherWORKS II NICs (DE200, DE201, DE202,
DE422). DEPCA-style boards prior to the DE200 have not been tested
and may not work.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
put vers.o at the end of the loader line. We are simply jumping in the
moment into the first location of the text segment in 386bsd. So the
linking order is very important :-). With the addition of the const
types in newvers.sh we jumped into them. I have experimented with an
entry point specification, but was unsuccessfull. Someone else should
look at this.
devices.i386:
files.i386:
Added entries for a Sony cdrom driver.
