Although groff_mdoc(7) gives another impression, this is the ordering
most widely used and also required by mdocml/mandoc.
Reviewed by: ru
Approved by: philip, ed (mentors)
and ipv6_ifconfig_<interface> options have already been deprecated,
these changes do not alter that.
With these changes any value set for ipv6_enable will emit a
warning. In order to avoid a POLA violation for the deprecation
of the option ipv6_enable=NO will still disable configuration
for all interfaces other than lo0. ipv6_enable=YES will not have
any effect, but will emit an additional warning. Support and
warnings for this option will be removed in FreeBSD 10.x.
Consistent with the current code, in order for IPv6 to be configured
on an interface (other than lo0) an ifconfig_<interface>_ipv6
option will have to be added to /etc/rc.conf[.local].
1. Clean up and minor optimizations for the following functions:
ifconfig_up (the ipv6 elements)
ipv6if
ipv6_autoconfif
get_if_var
_ifconfig_getargs
The cleanups generally were to move the "easy" tests earlier in the
functions, and consolidate duplicate code.
2. Stop overloading ipv6_prefer with the ability to disable IPv6
configuration.
3. Remove noafif() which was only ever called from ipv6_autoconfif.
Instead, simplify and integrate the tests into that function, and
convert the test to use is_wired_interface() instead of listing
wireless interfaces explicitly.
4. Integrate backwards compatibility for ipv6_ifconfig_<interface>
into _ifconfig_getargs. This dramatically simplifies the code in
all of the callers, and avoids a lot of other code duplication.
5. In rc.d/netoptions, add code for an ipv6_privacy option to use
RFC 4193 style pseudo-random addresses (this is what windows does
by default, FYI).
6. Add support for the [NO]RTADV options in ifconfig_getargs() and
ipv6_autoconfif(). In the latter, include support for the explicit
addition of [-]accept_rtadv in ifconfig_<interface>_ipv6 as is done
in the current code.
7. In rc.d/netif add a warning if $ipv6_enable is set, and remove
the set_rcvar_obsolete for it. Also remove the latter from
rc.d/ip6addrctl.
8. In /etc/defaults/rc.conf:
Add an example for RTADV configuration.
Set ipv6_network_interfaces to AUTO.
Switch ipv6_prefer to YES. If ipv6_enable is not set this will have
no effect.
Add a default for ipv6_privacy (NO).
9. Document all of this in rc.conf.5.
Note that this is actually a no-op for most users, as this GNU
cpio was broken on -HEAD and 8-STABLE since last March until
the recent fix.
FreeBSD 8.0+ uses BSD cpio by default and the code is being
actively maintained.
Blessed by: kientzle
With hat: secteam
MFC after: 3 days
At least in RELENG_7 this fixes some start problems for some programs
from the ports. It is also more correct, as a jail shall not expect
input (interactivity) from the jail-host.
Revert the current behavior of starting jails in the background and
make it optional only for the start of jails (jail_parallell_start=YES
in rc.conf):
- The stop can not be done in the background, the system needs to wait
until everything is stopped correctly before it can reboot or power
down.
- The start should not be done in parallel by default, this not only
breaks POLA for people comming from RELENG_x, it may also break a
dependency chain with other scripts in the jail-host, which need to
do some stuff after the jails are up and running (e.g. hardlinking
a mysql socket from one jail into another one).
Discussed on: freebsd-jails@
HAST allows to transparently store data on two physically separated machines
connected over the TCP/IP network. HAST works in Primary-Secondary
(Master-Backup, Master-Slave) configuration, which means that only one of the
cluster nodes can be active at any given time. Only Primary node is able to
handle I/O requests to HAST-managed devices. Currently HAST is limited to two
cluster nodes in total.
HAST operates on block level - it provides disk-like devices in /dev/hast/
directory for use by file systems and/or applications. Working on block level
makes it transparent for file systems and applications. There in no difference
between using HAST-provided device and raw disk, partition, etc. All of them
are just regular GEOM providers in FreeBSD.
For more information please consult hastd(8), hastctl(8) and hast.conf(5)
manual pages, as well as http://wiki.FreeBSD.org/HAST.
Sponsored by: FreeBSD Foundation
Sponsored by: OMCnet Internet Service GmbH
Sponsored by: TransIP BV
specify list of executables and/or rc scripts that should be executed
after firewall starts/stops.
Submitted by: Yuri Kurenkov <y dot kurenkov at init dot ru>
Reviewed by: rhodes, rc@
MFC after: 1 week
maximum file size limit. Default is UINT64_MAX when the option is
not specified. It was useless to set the limit to the total amount of
memory and swap in the system.
Use tmpfs_mem_info() rather than get_swpgtotal() in tmpfs_mount() to
check if there is enough memory available.
Remove now unused get_swpgtotal().
Reviewed by: Gleb Kurtsou
Approved by: trasz (mentor)
wlan(4) interfaces. vlan(4) interfaces are listed via a new 'vlans_<IF>'
variable. If a vlan interface is a number, then that number is treated as
the vlan tag for the interface and the interface will be named '<IF>.<tag>'.
Otherwise, the vlan tag must be provided via a vlan parameter in a
'create_args_<vlan>' variable.
While I'm here, fix a few nits in rc.conf(5) and mention create_args_<IF> in
the description of cloned_interfaces.
Reviewed by: brooks
MFC after: 2 weeks
re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
network_ipv6->rc.d/netif integration:
- $ipv6_enable is now obsolete. Instead, IPv6 is enabled by
default if the kernel supports it, and $ipv6_network_interfaces
is "none" by default. If you want to use IPv6, define
$ipv6_network_interfaces and $ifconfig_xxx_ipv6.
An interface which is in $network_interfaces and not in
$ipv6_network_interfaces will be marked as "inet6
-auto_linklocal ifdisabled" (see ifconfig(8)).
- $ipv6_ifconfig_xxx is renamed to ifconfig_xxx_ipv6 for
consistency with other address families. The old variables
still work but can be removed in the future. Note that
ipv6_ifconfig_xxx="..." should be replaced with
ifconfig_xxx_ipv6="inet6 ...".
- Receiving ICMPv6 Router Advertisement is not automatically
enabled even if there is no manual configuration of IPv6 in
rc.conf. If you want it, define
ifconfig_xxx_ipv6="inet6 ... accept_rtadv".
- The rc.d/ip6addrctl now chooses address selection policy based
on $ipv6_prefer, not $ipv6_enable. The default is
ipv6_prefer=NO.
- $router* and $ipv6_router* are replaced with $routed_* and
$route6d_* for consistency. The old variables still work but
can be removed in the future.
MFC after: 3 days
statically bind IPv4 <-> MAC address at boot time.
In order to use this, the administrator needs to configure the following
rc.conf(5) variable:
- static_arp_pairs: A list of names for static bind pairs, and,
- a series of static_arp_(name): the arguments that is being passed to
``arp -S'' operation.
Example:
static_arp_pairs="gw"
static_arp_gw="192.168.1.1 00:01:02:03:04:05"
See the rc.conf(5) manual page for more details.
Reviewed by: -rc@
MFC after: 2 weeks
using freebsd-update. This applies to using freebsd-update in "upgrade
mode" and normal freebsd-update on a security branch.
The backup kernel will be written to /boot/kernel.old, if the directory
does not exist, or the directory was created by freebsd-update in a
previous backup. Otherwise freebsd-update will generate a new directory
name for use by the backup. By default symbol files are not backed up
to save diskspace and avoid filling up the root partition.
This feature is fully configurable in the freebsd-update config file,
but defaults to enabled.
MFC after: 1 week (stable/7)
Reviewed by: cperciva
Approved by: re (kib)
the number of days between backups. All it says is frequency, with no
units given. It likely should say "the interval in days between backups"
instead, but not today.
(localhost by default) can be successfully looked up. Off by default.
2. New feature: option to create a forwarder configuration file based on
the contents of /etc/resolv.conf. This allows you to utilize a local
resolver for better performance, less network traffic, custom zones, etc.
while still relying on the benefits of your local network resolver.
Off by default.
3. Add named-checkconf into the startup routine. This will prevent named
from trying to start in a situation where it would not be possible to do
so.
arbitrary commands (outside the jail) associated with said events,
e.g. to bring up/down CARP interfaces representing services run in
jails.
Reviewed by: simon
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
the -g and -q options. They do a slightly different thing and
both are necessary when the time difference is large.
Noticed by: danger, in the forums
Approved by: roberto
MFC after: 1 week
Note: this is only really necessary because of the ifconfig
logic to add/remove the jail IPs upon start/stop.
Consensus among simon and I is that the logic should
really be factored out from the startup script and put
into a proper management solution.
- We now support starting of no-IP jails.
- Remove the global jail_<jname>_netmask option as it is only
helpful to set netmasks/prefixes for the right address
family and per address.
- Implement jail_<jname>_ip options to support both
address familes with regard to ifconfig logic.
- Implement _multi<n> support suffix to the jail_<jname>_ip
option to configure additional addresses to avoid overlong,
unreadbale jail_<jname>_ip lines with lots of addresses.
Submitted by: initial work from Ruben van Staveren
Discussed on: freebsd-jail in Nov 2008.
Reviewed by: simon, ru (partial, older version)
MFC after: 1 week
in /etc/fstab. We do support passing special options on a per
filesystem type basis, like `-u UID -g GID' for mount_msdosfs, but
the syntax of these options in fstab is non-obvious and a lot of
users have asked about it.
PR: docs/128816
Submitted by: Roland Smith, rsmith at xs4all dot nl
MFC after: 2 days
documents away from being public accessible. Replace link to
the Bluetooth specification document with the document name.
Pointed out by: SoftLover < slserg at uic dot tula dot ru >
MFC after: 3 days
parts relied on the now removed NET_NEEDS_GIANT.
Most of I4B has been disconnected from the build
since July 2007 in HEAD/RELENG_7.
This is what was removed:
- configuration in /etc/isdn
- examples
- man pages
- kernel configuration
- sys/i4b (drivers, layers, include files)
- user space tools
- i4b support from ppp
- further documentation
Discussed with: rwatson, re
To preserve the existing behavior of etc/rc.d/netif, add code to wait
up to if_up_delay seconds (30 seconds by default) for a default route to
be configured if there are any dhcp interfaces. This should be extended
to test that the interface is actually up.
X-MFC after:
more wlans_<ifn> and create_args_<ifn>
Add documentation for these variants and generally update the wireless
device example.
There is are very short lived shim from vaps_<ifn> which produces
a warning and vap_create_<ifn> which does not. Misuse the MFC
notification service to remind me to remove them.
MFC after: 3 weeks
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
mode at boot time. Multiple profiles can be started at the same time.
The whole idea is very similar to the ppp rc script.
Document Bluetooth knobs in rc.conf(5)
MFC after: 1 week
per-profile variables of the form ppp_<profile>_unit. No ppp_unit
variable is supported since tying the same unit to more than one profile
won't work.
PR: conf/122127
MFC after: 1 week
to _ when evaluating ppp_<profile>_nat and ppp_<profile>_mode. Document
the per-profile variables.
PR: conf/121452, conf/122127 (partial)
MFC after: 1 week
scripts at boot. This is currently disabled by default. /etc/ddb.conf
contains some potentially reasonable default scripts.
PR: conf/119995
Submitted by: Scot Hetzel <swhetzel at gmail dot com> (Earlier version)
X-MFC after: textdumps
included in the kernel by default. Remove reference to this option
from defaults/rc.conf and rc.conf(5).
PR: conf/119098
Submitted by: Beat Gaetzi
MFC after: 1 week
upgrading to new releases. Important parts of this code include
* automatically determining which optional components (e.g., src,
info, proflibs) are installed.
* merging changes in files which are modified locally and have
changed between the currently running and new release.
* prompting the user to rebuild all 3rd party software before
deleting old shared libraries.
Yes, this is compatible with "freebsd-update rollback" -- you can
test a new -BETA and roll back to the old release if you don't
like it.
Subject to re@ approval, this will be MFCed before 7.0-BETA3 and
6.3-RC1.
MFC after: 2 days
selected interface. wpa_supplicant does not only handle WPA
authentication but also EAP/LEAP as well as WEP encryption or no
encryption at all. The patch clarifies this.
PR: 117046
Submitted by: lme
Reviewed by: bruffer
Approved by: jkois (mentor)
This commit includes the following core components:
* sample configuration file for sensorsd
* rc(8) script and glue code for sensorsd(8)
* sysctl(3) doc fixes for CTL_HW tree
* sysctl(3) documentation for hardware sensors
* sysctl(8) documentation for hardware sensors
* support for the sensor structure for sysctl(8)
* rc.conf(5) documentation for starting sensorsd(8)
* sensor_attach(9) et al documentation
* /sys/kern/kern_sensors.c
o sensor_attach(9) API for drivers to register ksensors
o sensor_task_register(9) API for the update task
o sysctl(3) glue code
o hw.sensors shadow tree for sysctl(8) internal magic
* <sys/sensors.h>
* HW_SENSORS definition for <sys/sysctl.h>
* sensors display for systat(1), including documentation
* sensorsd(8) and all applicable documentation
The userland part of the framework is entirely source-code
compatible with OpenBSD 4.1, 4.2 and -current as of today.
All sensor readings can be viewed with `sysctl hw.sensors`,
monitored in semi-realtime with `systat -sensors` and also
logged with `sensorsd`.
Submitted by: Constantine A. Murenin <cnst@FreeBSD.org>
Sponsored by: Google Summer of Code 2007 (GSoC2007/cnst-sensors)
Mentored by: syrinx
Tested by: many
OKed by: kensmith
Obtained from: OpenBSD (parts)
I did this in the previous commit, leaves out the parsing of $FreeBSD$
which is actually required to be parsed.
Kindly reminded by: bmah
Approved by: re (bmah)
Approved by: imp (mentor, implicit)
Document the SENDMAIL_ALIASES, SENDMAIL_MAP_SRC, SENDMAIL_MAP_TYPE, and
SENDMAIL_START_SCRIPT
.Xr make.conf 5
variables.
These are used in
.Pa /etc/mail/Makefile .
PR: conf/40548
MFC after: 3 days
in the description of `moused_flags', instead of the later), and
add a description of `moused_XXX_flags' where `XXX' is the port
name of a non-default moused invocation -- including an example
of using "-3" with the default moused(8) instance, but no special
flags for moused(8) invocations handling 3-button USB mice (which
seems a very common scenario these days).
MFC after: 3 days
which can be used to turn off multicast pfsync support, and enable
the transmission of directed PFSYNC (IP protocol: 240) packets to
a specific "sync peer" host.
PR: conf/111225
Submitted by: Bas van Beek <bas@tobin.nl>
Approved by: mtm, mlaier
MFC after: 2 weeks
the background fsck indefinitely. This allows the administrator to run
it at a convenient time. To support running it from cron, the
forcestart argument now causes the fsck to start with no delay and all
output to be suppressed.
for /tmp and /var. This makes the memory discs swap-backed instead
of malloc-backed. A swap-backed memory disc should not be worse
than a malloc-backed one in any scenario because it will start
touching swap only when needed. OTOH, a malloc-backed disc can
starve limited kernel resources and evenually crash the system.
Reflect the change in the rc.conf(5) manpage. Also stop telling
lies there about softupdates: it does not waste disc space, it
just can delay its freeing.
Suggested by: many
PR: kern/87255
MFC after: 1 week
<sys/extattr.h> to <ufs/ufs/extattr.h>. Move description
of extended attributes in UFS from man9/extattr.9 to
man5/fs.5.
Note that restore will not compile until <sys/extattr.h>
and <ufs/ufs/extattr.h> have been updated.
Suggested by: Robert Watson
