controller found in the MBP2013 has been observed to not work properly
unless this operation is performed.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
value. The "Intel Lynx Point" XHCI controller found in the MBP2013 has
been observed to not always set the event interrupt bit while there
are events to consume in the event ring.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
Some Intel XHCI controlles timeout processing so-called "TRBs" when
the final LINK TRB of a so-called "TD" has the CHAIN-BIT set.
MFC after: 1 week
Tested by: glebius @
receiving Zero Length Packets, ZLPs. See comment in code for more
information.
MFC after: 1 week
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
routing if we get certain errors. Poll for command completion upon
command timeouts. The XHCI error events might not generate interrupts.
MFC after: 1 week
Reported by: Daniel Gerzo <danger@rulez.sk>, Antonis Anastasiadis <anastasiadis@datalive.gr>
PR: usb/181159
Approved by: re (gjb)
IMAN register to clear the pending interrupt status bits. This patch
tries to solve problems seen on the MacBook Air, as reported by
Johannes Lundberg <johannes@brilliantservice.co.jp>
MFC after: 1 week
The Block Event Interrupts, BEI, feature does not
work like expected with the Renesas XHCI chipsets.
Revert feature.
While at it correct the TD SIZE computation in
case of Zero Length Packet, ZLP, in the end of a
multi frame USB transfer.
MFC after: 1 week
PR: usb/180726
1) Only multi-TD isochronous transfers should use NORMAL
type after specific type as per XHCI specification.
2) BEI bit is only available in NORMAL and ISOCHRONOUS
TRB types. Don't use this bit for other types to avoid
hardware asserts. Reserved bits should be don't care
though ...
MFC after: 1 week
PR: usb/179342
the regular interrupt handler is not working properly or
in case of MSI interrupts which are not yet supported.
Remove interrupt setup code for FreeBSD versions older
than 700031.
MFC after: 1 week
PR: usb/179342
into the FreeBSD boot loader, typically for non-USB aware BIOSes, EFI systems
or embedded platforms. This is also useful for out of the system compilation
of the FreeBSD USB stack for various purposes. The USB kernel files can
now optionally include a global header file which should include all needed
definitions required to compile the FreeBSD USB stack. When the global USB
header file is included, no other USB header files will be included by
default.
Add new file containing the USB stack configuration for the
FreeBSD loader build.
Replace some __FBSDID()'s by /* $FreeBSD$ */ comments. Now all
USB files follow the same style.
Use cases:
- console in loader via USB
- loading kernel via USB
Discussed with: Hiroki Sato, hrs @ EuroBSDCon
This patch will save CPU time when the XHCI interrupt is
shared with other devices.
Only check event rings when interrupt bits are set.
Otherwise would indicate hiding possible hardware fault(s).
Tested by: sos @
Submitted by: sos @
MFC after: 1 week
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
in SUPER-speed mode, USB 3.0.
This feature has not been tested yet, due to lack of hardware.
This feature is useful when implementing protocols like UASP,
USB attached SCSI which promises higher USB mass storage throughput.
This patch also implements support for hardware processing of endpoints
for increased performance. The switching to hardware processing
of an endpoint is done via a callback to the USB controller driver. The
stream feature is implemented like a variant of a hardware USB protocol.
USB controller drivers implementing device mode needs to be updated to
implement the new "xfer_stall" USB controller method and remove the
"xfer" argument from the "set_stall" method.
The API's toward existing USB drivers are preserved. To setup a USB transfer
in stream mode, set the "stream_id" field of the USB config structure to
the desired value.
The maximum number of BULK streams is currently hardcoded and limited to 8
via a define in usb_freebsd.h.
All USB drivers should be re-compiled after this change.
LibUSB will be updated next week to support streams mode. A new IOCTL to
setup BULK streams as already been implemented. The ugen device nodes
currently only supports stream ID zero.
The FreeBSD version has been bumped.
MFC after: 2 weeks
This will give you more bandwidth for isochronous
FULL speed applications connected through a
High Speed HUB.
This patch has been tested with XHCI and EHCI.
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
