request and just calling it when we get a bridge interrupt. The
problem is that if other code wants to block hardware interrupts for a
little bit with splXXX, those masks aren't updated the way we're doing
it. This doesn't matter for -current, but does for -stable.
The whole reason that we were catching interrupts was to detect that
the card was still there. Ian's fixes however ensure that the card
will be there with an interrupt handler, or not there at all. Since
the pcic interrupt is at a high priority, this should be OK.
This should fix the network related crashes people started seeing in
stable after I merged the pcic as a pci device code.
Submitted indirectly by: Ian Dowse
MFC when: Ian has had a chance to do his torture hang testing.
the ISR. We keep track of the card state and don't call the IRS when
the card isn't inserted. This helps quite a bit with card ejection
problems that Ian was seeing.
Submitted by: Ian Dowse
MFC upon: re approvel.
register. It enables Zoom Video. It appears that on at least one
card that Monzoon is using sets these bits by default. Nothing works
when these bits are set, everything works when they are clear.
Add commentary on some of the ti bits. Make code a little clearer.
Also remove a call to pcic_pci_pd6729 which was prematurely added in
the last commit.
is the diagnostics register at offset 0x93. When bit 5 is set in this
register, bits 4-7 in ExCA register 0x5 being 0000 are required for
pci interrupt routing. When it is clear, then bit 4 of ExCA register
0x3 is used to enable it.
The only other issue is that when you route interrupts this way, you
must read ExCA register 0x4 in order to clear the interrupt, else you
get an interrupt storm.
Deal with this requirement by setting things up. It is believed that
this won't hurt other chipsets, but other chipsets may require their
own work arounds.
o Move PIOCSRESOURCE from pccard to pcic so the kernel can give pccardd
better hints as to what resources to use.
o Implement an undocumented hw.pcic.interrupt_route to allow people that
need to do so to route their interrupts in a non-standard way.
o Only preallocate a resource in probe if we're routing via pci.
o If we aren't routing via pci, then set the irq to use explicitly
to defeat the automatic IRQ routing of the pci layer.
This, with the pccardd code should be close to what can be committed
to -stable.
hw.pcic.irq Globally set the IRQ for all pcic devices' management
interrupt (aka card status change or CSC interrupt)
This is what used to be known as
machdep.pccard.pcic_irq (which has been retained for
now for compatibility).
hw.pcic.ignore_fuction_1 Ignores function 1 for all PCIC bridges by not
attaching to them. Lucent released a huge batch
of cards that were imporperly manufactuered (lacking
the 0 ohm resister to disable slot 1). This is
a big hammer to keep those cards from causing problems
(I've had 4 people contact me saying my patches
worked great once they added a kludge to always ignore
function 1, or until they soldered these resistors
in place!).
No clue where to document these. They act as both boot loader environment
variables, as well as read-only sysctls after boot.
At the same time, sort sys/systm.h in its proper order after sys/sysctl.h.
o kill blank line that I introduced in cardinfo.h
o Delete unused variable wasinactive.
o return 0 from pccard_resume.
o Set the state and lastsate initially to be empty.
o move comment above code for interrupt dispatching.
o Powerstate interface is now available as of 430002, not 500000 (note that
this change will be not 100% correct since the power state stuff didn't
enter current until well after 500000, but it is good enough for the two
branche we have going now).
Sometimes, when pccardd is restarted, it fails to realize that the
device is already attached and tries to attach it again. This leads
to bad mojo since the pccard code isn't setup to handle that, so the
panic was put in. Now it appears that it is triggering too easily, so
I'm backing it off to a non-fatal error.
Frist, for pci slots, make the setup intr save the requested interrupt
vector and arg and return rather than passing it up to our parent. On
interrupts, we call this vector iff there's a card in the slot. This
should eliminate some of the hangs or "weird" messages that people see
when ejecting cards and also help close the race window somewhat.
Reading the pci bus one more time for this information is judged to be
an acceptible tradeoff since it is very very fast.
Cleanup a little how we detect unsupported cards. Only detect
unsupported cards (eg cardbus cards) on card insertion (or more
pedantically when a card is actually present). This should allow us
to change the message in the future to "cardbus card not supported
with OLDCARD" :-).
Note:
We may also consider this for the ISA bus case, but there the
reads are much more expensive and the location of the CD pin
status lines appears to be less standardized. Also, the ISA
management interrupt isn't shared with the card's interrupt.
The mutliplex the CSC and function interrupts bit also appears
to be non-standard (or at least not imlemented on all
bridges).
because NEWBUS (and I think some versions of Windows sometimes) writes
0xffffffff to these registers to disable them. When they are
"disabled" like this, writing memory ranges to the pcic registers are
ignored and you will get "card (null) (null)" when you insert a call
otherwise.
each of the bridge chips. Before we wrongly assumes that all cardbus
bridge chips were intel compatible step A/B. This mostly worked, but
likely caused problems with certain cirrus logic cardbus bridges.
information until the problems can be tracked down. Right now these
are unconditional, but later it will be hidden behind a boot verbose.
Also, if there are no events listed in the event mask, return right
away. Specifically avoid writing back interrupt acks in this case.
Print type of pci bridge we find.
Force the IRQ of pci bridges upon all its children.
Allocate the resources on behalf of the bridge when we're testing to see if
they exist.
This should help people who don't read updating instructions very well.
This patch started out with an idea from Shigeru Yamamoto-san in -current.
higher chips. Treat it as if it were a 113x. This is correct as far
as 16-bit cards go, at least how we're using it.
# It appears that my TI-1031 based pci card that YAMAMOTO shigeru-san gave
# me on my trip to Japan now works.
elected to do this in the probe rather than the attach so that we don't
disturb things which this might reset. different cards have different
quirks, according to their datasheets.
This should fix the "I booted in windows and rebooted to FreeBSD and
now things don't work" problem.
PR: 4847, 20670
card bus bridges.
We now always use pci interrupts for pci cards. This will allow us to
more easily configure things. You must change your IRQ lines in
/etc/pccard.conf to match what we've probed. I'm not sure the right
way to deal with this right now.
Development of pci pcmcia has been funded by Monzoon Networks AG. I
am grateful for their generosity.
o If the class is PCIC_BRIDGE, subclass is PCIS_BRIDGE_PCMCIA and
programming interface is 0, assume that it is a generic PCMCIA PCI
chip we can program. I don't think there are any of these that
we don't know about, but you never know.
o If the class is PCIC_BRIDGE, subclass is PCIS_BRIDGE_CARDBUS and
programming interface is 0, assume that it is a YENTA cardbus bridge
that we know how to cope with. There are likely some cardbus bridges
that haven't it made it in here yet.
of the pcic class of devices. Go ahead and move it to the "usual"
place. I say "usual" in quotes since it isn't exactly right (not in
dev/blah), but it is closer than before.
parts. This is based on the newcard code that turns it off :-). We
can now reboot after NEWCARD or Windows and have OLDCARD work. Add
support for the RL5C466 while I'm at it.
Treat TI1031 the same as the CLPD6832. It doesn't work yet, but sucks
less than it did before.
Also add a few #defines for other changes in the pipe.
This don't hurt anything.
PCI/CardBus Bridge -> PCI-CardBus Bridge
Submitted by: Takeshi Shibagaki <sibagaki@lsi.melco.co.jp>
Obtained from: bsd-nomads ML in Japan
cardbus bridge init routine for all cardbuses. This routine attempts
to compensate for BIOSes that do not setup the cardbus bridge into
legacy mode. Since this is becoming more common, and cardbus pci
cards have appeared on the market, this makes sense.
Do some TI113x specific initialization. This came in as part of the
patch. Report TI1[1234]XX specific config registers protected by
bootverbose.
Minor code cleanup while I'm here. I've also removed the unused code
present in the original patches, and cleaned it up slightly in places
as well.
The original patches supported more than one card, but these patches
support just one. We should likely revisit this in the future.
This makes the Compaq card that Walnut Creek CD purchased for me work
in my bouncer box.
This is a MFC candidate. However, I'd like to get some airtime on
these patches on as many laptops as possible before doing the MFC. It
does change things somewhat. In theory, apart from the minor TI
tweaks, this shouldn't change anything if the bridge is in legacy mode
already.
Submitted by: sanpei@sanpei.org (MIHIRA Yoshiro)
conversion to eliminate the compatability shims without making any
significant changes. This eliminates the shim warnings.
Obtained from: n_himba (tweaked by me, don't blame him for this)
Approved by: jkh
probes are at the 'chip' level and will get overridden by pcic_p if it is
compiled in. It's still nice to get the better probe message if it's not...
Requested by: imp
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
and initializes the next two ports in order starting at 03e0. This
also patches pcic_p.h to reduce the I/O ports mapped from 4 to 2.
Submitted by: Ted Faber <faber@ISI.EDU>
mode. Currently, the only supported controller is the Cirrus Logic
PD6832, but others can be supported with docs on them.
Submitted by: Ted Faber <faber@ISI.EDU>
