locking in tcp_input() for TCP packets with urgent data pointers to
hold the socket buffer lock across testing and updating oobmark
from just protecting sb_state.
Update socket locking annotations
Ultra2 users may want to set OFWCONS_POLL_HZ to a value of '20'.
I have left default value at '4' as higher values can consume a more
than is acceptable amount of CPU, and we don't have a consensus yet
what is an optimal value.
Submitted by: Pyun YongHyeon <yongari@kt-is.co.kr>
not active GEOM providers, it will result in a kernel panic.
If the GEOM provider or disk goes away before the volume
configuration data gets written to the disk, it will result
in another kernel panic.
o Make sure that the drives specified for volume creation
are active GEOM providers.
o When writing out volume configuration data to associated drives,
make sure that the GEOM provider is active, otherwise continue
to the next drive in the volume.
Approved by: le, bmilekic (mentor)
Giant if debug.mpsafenet=0, as any points that require synchronization
in the SMPng world also required it in the Giant-world:
- inpcb locks (including IPv6)
- inpcbinfo locks (including IPv6)
- dummynet subsystem lock
- ipfw2 subsystem lock
- Assert the mutex in NG_IDHASH_FIND() since the mutex is required to
safely walk the node lists in the ng_ID_hash table.
- Acquire the ng_nodelist_mtx when walking ng_allnodes or ng_allhooks
to generate state dump output from the netgraph sysctls.
the socket buffer having its limits adjusted. sbreserve() now acquires
the lock before calling sbreserve_locked(). In soreserve(), acquire
socket buffer locks across read-modify-writes of socket buffer fields,
and calls into sbreserve/sbrelease; make sure to acquire in keeping
with the socket buffer lock order. In tcp_mss(), acquire the socket
buffer lock in the calling context so that we have atomic read-modify
-write on buffer sizes.
smp_rendezvous() to ensure we run on the BSP. This reverts rev 1.128.
Add a comment indicating that MI code should be the one that runs all
shutdown functions on the BSP with the APs halted. This should work
around problems in power off while waiting for the MI code to be improved.
waiting for the socket to connect and use msleep() on the socket
mute rather than tsleep(). Acquire socket buffer mutexes around
read-modify-write of socket buffer flags.
The general UMA lock is a recursion-allowed lock because
there is a code path where, while we're still configured
to use startup_alloc() for backend page allocations, we
may end up in uma_reclaim() which calls zone_foreach(zone_drain),
which grabs uma_mtx, only to later call into startup_alloc()
because while freeing we needed to allocate a bucket. Since
startup_alloc() also takes uma_mtx, we need to be able to
recurse on it.
This exact explanation also added as comment above mtx_init().
Trace showing recursion reported by: Peter Holm <peter-at-holm.cc>
(aka "command") will display "<defunct>", as does the output from "comm"
for those processes. Also do better checking for malloc() failures.
Submitted by: Cyrille Lefevre
originated on RELENG_4 and was ported to -CURRENT.
The scoreboarding code was obtained from OpenBSD, and many
of the remaining changes were inspired by OpenBSD, but not
taken directly from there.
You can enable/disable sack using net.inet.tcp.do_sack. You can
also limit the number of sack holes that all senders can have in
the scoreboard with net.inet.tcp.sackhole_limit.
Reviewed by: gnn
Obtained from: Yahoo! (Mohan Srinivasan, Jayanth Vijayaraghavan)
This should fix problems with older SMP systems that only have ISA/EISA
IRQs when routing virgin PCI interrupts as well as on other boxes whose
MADT does not have any interrupt override entries for ISA IRQs that are
used to route PCI interrupts even in APIC mode.
actually used. For most ACPI devices this means deferring the call
until bus_alloc_resource().
- Add a function acpi_config_intr() to call BUS_CONFIG_INTR() for an
ACPI IRQ resource using the trigger mode and polarity information
stored in the ACPI resource object.
- Add a function acpi_lookup_irq_resource() to lookup the ACPI IRQ
resource that corresponds to a specified rid and new-bus resource.
- Have the ACPI PCI bridge driver call BUS_CONFIG_INTR() on interrupts
that it routes through link devices.
- Remove needactivate variable from acpi_alloc_resource() by changing the
function not modify the flags variable but just mask off RF_ACTIVE when
calling rman_reserve_resource().
Reviewed by: njl (1, an earlier version)
- Allow ioapic_set_{nmi,smi,extint}() to be called multiple times on the
same pin so long as the pin's mode is the same as the mode being
requested.
- Add a notion of bus type for the interrupt associated with interrupt pin.
This is needed so that we can force all EISA interrupts to be active high
in the forthcoming ioapic_config_intr().
- Fix a bug for EISA systems that didn't remap IRQs. This would have broken
EISA systems that tried to disable mixed mode for IRQ 0.
case of NFS mounted swap, so do not try to dereference it.
While we're here, brucify the printf() call which happens when we
time out on acquisition of vm_page_queue_mtx.
PR: kern/67898
Submitted by: bde (style)
device associated with any PCI devices that are enumerated in the ACPI
tree when adding children to an ACPI PCI bus and remove the duplicate
ACPI-only device_t and replace the device_t associated with the handle with
the ACPI and PCI aware device_t.
Several changes:
* Implement read for ulpt.
* If the device is not opened for reading, occasionally drain any
data the printer might have (but don't hammer the printer with reads).
* Lower the buffer size to one page.
The driver seems to work with more printers now.
Obtained from: NetBSD
