After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
- Add a pcib_detach() function for the PCI-PCI bridge driver. It
tears down the NEW_PCIB and hotplug state including destroying
resource managers, deleting child devices, and disabling hotplug
events.
- Add a detach method to the ACPI PCI-PCI bridge driver which calls
pcib_detach() and then frees the copy of the _PRT interrupt routing
table.
- Add a detach method to the PCI-Cardbus bridge driver which frees
the PCI bus resources in addition to calling cbb_detach().
- Explicitly clear any pending hotplug events during attach to ensure
future events will generate an interrupt.
- If a the Command Completed bit is set in the slot status register
when the command completion timeout fires, treat it as if the
command completed and the completion interrupt was just lost rather
than forcing a detach.
- Don't wait for a Command Completed notification if Command Completion
interrupts are disabled. The spec explicitly says no interrupt is
enabled when clearing CCIE, and on my T400 no interrupt is generated
when CCIE is changed from cleared to set, either. In addition, the
T400 doesn't appear to set the Command Completed bit in the cases
where it doesn't generate an interrupt, so don't schedule the timer
either. (If the CC bit were always set, one could always set the timer
and rely on the logic of treating CC set as a missed interrupt.)
Reviewed by: imp (older version)
Differential Revision: https://reviews.freebsd.org/D6424
Some ACPI operations such as mutex acquires and event waits accept a
timeout. The ACPI OSD layer implements these timeouts by using regular
sleep timeouts. However, this doesn't work during early boot before
event timers are setup. Instead, use polling combined with DELAY()
to spin.
This fixes booting on upcoming Intel systems with Kaby Lake processors.
Tested by: "Jeffrey E Pieper" <jeffrey.e.pieper@intel.com>
Reviewed by: jimharris
MFC after: 1 week
Currently, Application Processors (non-boot CPUs) are started by
MD code at SI_SUB_CPU, but they are kept waiting in a "pen" until
SI_SUB_SMP at which point they are released to run kernel threads.
SI_SUB_SMP is one of the last SYSINIT levels, so APs don't enter
the scheduler and start running threads until fairly late in the
boot.
This change moves SI_SUB_SMP up to just before software interrupt
threads are created allowing the APs to start executing kernel
threads much sooner (before any devices are probed). This allows
several initialization routines that need to perform initialization
on all CPUs to now perform that initialization in one step rather
than having to defer the AP initialization to a second SYSINIT run
at SI_SUB_SMP. It also permits all CPUs to be available for
handling interrupts before any devices are probed.
This last feature fixes a problem on with interrupt vector exhaustion.
Specifically, in the old model all device interrupts were routed
onto the boot CPU during boot. Later after the APs were released at
SI_SUB_SMP, interrupts were redistributed across all CPUs.
However, several drivers for multiqueue hardware allocate N interrupts
per CPU in the system. In a system with many CPUs, just a few drivers
doing this could exhaust the available pool of interrupt vectors on
the boot CPU as each driver was allocating N * mp_ncpu vectors on the
boot CPU. Now, drivers will allocate interrupts on their desired CPUs
during boot meaning that only N interrupts are allocated from the boot
CPU instead of N * mp_ncpu.
Some other bits of code can also be simplified as smp_started is
now true much earlier and will now always be true for these bits of
code. This removes the need to treat the single-CPU boot environment
as a special case.
As a transition aid, the new behavior is available under a new kernel
option (EARLY_AP_STARTUP). This will allow the option to be turned off
if need be during initial testing. I plan to enable this on x86 by
default in a followup commit in the next few days and to have all
platforms moved over before 11.0. Once the transition is complete,
the option will be removed along with the !EARLY_AP_STARTUP code.
These changes have only been tested on x86. Other platform maintainers
are encouraged to port their architectures over as well. The main
things to check for are any uses of smp_started in MD code that can be
simplified and SI_SUB_SMP SYSINITs in MD code that can be removed in
the EARLY_AP_STARTUP case (e.g. the interrupt shuffling).
PR: kern/199321
Reviewed by: markj, gnn, kib
Sponsored by: Netflix
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Compared to the r298933, this version uses 'struct _cpuset' in
<sys/bus.h> instead of 'cpuset_t' to avoid requiring <sys/param.h>
(<sys/_cpuset.h> still requires <sys/param.h> for MAXCPU even though
<sys/_bitset.h> does not after recent changes).
PCI-express HotPlug support is implemented via bits in the slot
registers of the PCI-express capability of the downstream port along
with an interrupt that triggers when bits in the slot status register
change.
This is implemented for FreeBSD by adding HotPlug support to the
PCI-PCI bridge driver which attaches to the virtual PCI-PCI bridges
representing downstream ports on HotPlug slots. The PCI-PCI bridge
driver registers an interrupt handler to receive HotPlug events. It
also uses the slot registers to determine the current HotPlug state
and drive an internal HotPlug state machine. For simplicty of
implementation, the PCI-PCI bridge device detaches and deletes the
child PCI device when a card is removed from a slot and creates and
attaches a PCI child device when a card is inserted into the slot.
The PCI-PCI bridge driver provides a bus_child_present which claims
that child devices are present on HotPlug-capable slots only when a
card is inserted. Rather than requiring a timeout in the RC for
config accesses to not-present children, the pcib_read/write_config
methods fail all requests when a card is not present (or not yet
ready).
These changes include support for various optional HotPlug
capabilities such as a power controller, mechanical latch,
electro-mechanical interlock, indicators, and an attention button.
It also includes support for devices which require waiting for
command completion events before initiating a subsequent HotPlug
command. However, it has only been tested on ExpressCard systems
which support surprise removal and have none of these optional
capabilities.
PCI-express HotPlug support is conditional on the PCI_HP option
which is enabled by default on arm64, x86, and powerpc.
Reviewed by: adrian, imp, vangyzen (older versions)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6136
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Reviewed by: wblock (manpage)
Differential Revision: https://reviews.freebsd.org/D5519
Arguably we should only be doing the probe/attach to children of
these devices as well.
Tested by: Michal Stanek <mst_semihalf.com> (arm64)
Differential Revision: https://reviews.freebsd.org/D6133
This allows the PCI-PCI bridge driver to save a reference to the child
device in its softc.
Note that this required moving the "pci" device creation out of
acpi_pcib_attach(). Instead, acpi_pcib_attach() is renamed to
acpi_pcib_fetch_prt() as it's sole action now is to fetch the PCI
interrupt routing table.
Differential Revision: https://reviews.freebsd.org/D6021
Both of the callers were expecting the input cap_set to be modified.
This fixes them to request cap_set to be updated with the returned buffer.
Reviewed by: jkim
Differential Revision: https://reviews.freebsd.org/D6040
Eventually with earlier AP startup this code will change to call the
startup function synchronously instead of queueing the task. Moving
the time we queue the task should be a no-op since taskqueue threads
don't start executing tasks until much later, but this reduces the diff
with the earlier AP startup patches.
Sponsored by: Netflix
Tell the firmware that we support PCI-express config space access
and MSI.
Reviewed by: jkim
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6023
This wrapper does not translate errors in the first word to ACPI
error status returns. Use this wrapper in the acpi_cpu(4) driver in
place of the existing _OSC code. While here, fix a bug where the wrong
count of words was passed when invoking _OSC.
Reviewed by: jkim
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6022
The ACPI and OFW PCI bus drivers as well as CardBus override this to
allocate the larger ivars to hold additional info beyond the stock PCI ivars.
This removes the need to pass the size to functions like pci_add_iov_child()
and pci_read_device() simplifying IOV and bus rescanning implementations.
As a result of this and earlier changes, the ACPI PCI bus driver no longer
needs its own device_attach and pci_create_iov_child methods but can use
the methods in the stock PCI bus driver instead.
Differential Revision: https://reviews.freebsd.org/D5891
VM_NUMA_ALLOC is used to enable use of domain-aware memory allocation in
the virtual memory system. DEVICE_NUMA is used to enable affinity
reporting for devices such as bus_get_domain().
MAXMEMDOM must still be set to a value greater than for any NUMA support
to be effective. Note that 'cpuset -gd' always works if MAXMEMDOM is
enabled and the system supports NUMA.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D5782
Previously, the ACPI PCI bus driver did a single pass over the devices in
the namespace that were a child of a given PCI bus to associate the
PCI bus-enumerated device_t devices with the corresponding ACPI handles.
However, this meant that handles were only established at runtime for devices
found during the initial PCI bus scan.
PCI_IOV adds devices that show up after the initial PCI bus scan, and coming
changes to add a bus rescan can also add devices after the initial scan.
This change adds a pci_child_added() callback to the ACPI PCI bus that walks
the namespace to find the ACPI handle for each device that is added. Using
a callback means that the handle is correctly set for any device no matter
how it is added (initial scan, IOV, or a bus rescan).
Instead of providing a wrapper around device_delete_child() that the PCI
bus and child bus drivers must call explicitly, move the bulk of the logic
from pci_delete_child() into a bus_child_deleted() method
(pci_child_deleted()). This allows PCI devices to be safely deleted via
device_delete_child().
- Add a bus_child_deleted method to the ACPI PCI bus which clears the
device_t associated with the corresponding ACPI handle in addition to
the normal PCI bus cleanup.
- Change cardbus_detach_card to call device_delete_children() and move
CardBus-specific delete logic into a new cardbus_child_deleted() method.
- Use device_delete_child() instead of pci_delete_child() in the SRIOV code.
- Add a bus_child_deleted method to the OpenFirmware PCI bus drivers which
frees the OpenFirmware device info for each PCI device.
Reviewed by: imp
Tested on: amd64 (CardBus and PCI-e hotplug)
Differential Revision: https://reviews.freebsd.org/D5831
On some architectures, u_long isn't large enough for resource definitions.
Particularly, powerpc and arm allow 36-bit (or larger) physical addresses, but
type `long' is only 32-bit. This extends rman's resources to uintmax_t. With
this change, any resource can feasibly be placed anywhere in physical memory
(within the constraints of the driver).
Why uintmax_t and not something machine dependent, or uint64_t? Though it's
possible for uintmax_t to grow, it's highly unlikely it will become 128-bit on
32-bit architectures. 64-bit architectures should have plenty of RAM to absorb
the increase on resource sizes if and when this occurs, and the number of
resources on memory-constrained systems should be sufficiently small as to not
pose a drastic overhead. That being said, uintmax_t was chosen for source
clarity. If it's specified as uint64_t, all printf()-like calls would either
need casts to uintmax_t, or be littered with PRI*64 macros. Casts to uintmax_t
aren't horrible, but it would also bake into the API for
resource_list_print_type() either a hidden assumption that entries get cast to
uintmax_t for printing, or these calls would need the PRI*64 macros. Since
source code is meant to be read more often than written, I chose the clearest
path of simply using uintmax_t.
Tested on a PowerPC p5020-based board, which places all device resources in
0xfxxxxxxxx, and has 8GB RAM.
Regression tested on qemu-system-i386
Regression tested on qemu-system-mips (malta profile)
Tested PAE and devinfo on virtualbox (live CD)
Special thanks to bz for his testing on ARM.
Reviewed By: bz, jhb (previous)
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D4544
acpi_GetInteger() execution. Intel DMAR interrupt remapping code
needs to know UID of the HPET to properly route the FSB interrupts
from the HPET, even when interrupt remapping is disabled, and the code
is executed under some non-sleepable mutexes.
Cache HPET UIDs in the device softc at the attach time and provide
lock-less method to get UID, use the method from the dmar hpet
handling code instead of calling GetInteger().
Reported and tested by: Larry Rosenman <ler@lerctr.org>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
to shut down; close laptop lid" scenario which otherwise tended to end
with a laptop overheating or the battery dying.
The implementation uses a new sysctl, kern.suspend_blocked; init(8) sets
this while rc.suspend runs, and the ACPI sleep code ignores requests while
the sysctl is set.
Discussed on: freebsd-acpi (35 emails)
MFC after: 1 week
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
drivers, one for fdt, one for acpi. It then uses this to decide if it will
use fdt or acpi.
The GICv2 (interrupt controller) and Generic Timer drivers have been
updated to handle both cases.
As this is early code we still need FDT to find the kernel console, and
some parts are still missing, including PCI support.
Differential Revision: https://reviews.freebsd.org/D2463
Reviewed by: jhb, jkim, emaste
Obtained from: ABT Systems Ltd
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
bridges only supported Intel Pentium and Pentium II era processors and there
is no reason for hardware virtualizations to emulate these quirks.
MFC after: 1 week
interacts with interrupts, query ACPI and use MWAIT for entrance into
Cx sleep states. Support C1 "I/O then halt" mode. See Intel'
document 302223-007 "Intelб╝ Processor Vendor-Specific ACPI Interface
Specification" for description.
Move the acpi_cpu_c1() function into x86/cpu_machdep.c and use
it instead of inlining "sti; hlt" sequence in several places.
In the acpi(4) man page, besides documenting the dev.cpu.N.cx_methods
sysctl, correct the names for dev.cpu.N.{cx_usage,cx_lowest,cx_supported}
sysctls.
Both jkim and avg have some other patches implementing the mwait
functionality; this work is unrelated. Linux does not rely on the
ACPI to provide correct tables describing Cx modes. Instead, the
driver has pre-defined knowledge of the CPU models, it was supplied by
Intel.
Tested by: pho (previous versions)
Sponsored by: The FreeBSD Foundation
