This is triggered only if BIOS configures ACPI_BITREG_BUS_MASTER_RLD
aka BRLD_EN_BM to 1.
Rationale:
1. we do not support C3 on PIIX4E
2. bus master activity need not break out of C2 state
3. because of CPU_QUIRK_NO_BM_CTRL quirk we may reset bus master
status which would result in immediate break out from C2
So if you have seen
cpu0: too many short sleeps, backing off to C1
with this chipset before you may want to try cx_lowest of C2 again.
Reviewed by: rpaulo (mentor), njl
Approved by: rpaulo (mentor)
if (batt_sleep_ms)
AcpiOsSleep(1);
where the rest are all:
if (batt_sleep_ms)
AcpiOsSleep(batt_sleep_ms);
I can't recall why that one was different, so change it
to match the rest.
Pointed out by: Christoph Mallon
MFC after: 2 weeks
On some laptops with smart batteries, enabling battery monitoring
software causes keystrokes from atkbd to be lost. This has also been
reported on Linux, and is apparently due to the keyboard and I2C line
for the battery being routed through the same chip. Whether that's
accurate or not, adding extra sleeps to the status checking code
causes the problem to go away.
I've been running this for nearly six months now on my laptop,
it works like a charm.
Reviewed by: Nate Lawson (in a previous revision)
MFC after: 2 weeks
- An "at" hint now reserves a device name.
- A new BUS_HINT_DEVICE_UNIT method is added to the bus interface. When
determining the unit number of a device, this method is invoked to
let the bus driver specify the unit of a device given a specific
devclass. This is the only way a device can be given a name reserved
via an "at" hint.
- Implement BUS_HINT_DEVICE_UNIT() for the acpi(4) and isa(4) bus drivers.
Both of these busses implement this by comparing the resources for a
given hint device with the resources enumerated by ACPI/PnPBIOS and
wire a unit if the hint resources are a subset of the "real" resources.
- Use bus_hinted_children() for adding hinted devices on isa(4) busses
now instead of doing it by hand.
- Remove the unit kludging from sio(4) as it is no longer necessary.
Prodding from: peter, imp
OK'd by: marcel
MFC after: 1 month
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
- Rename pciereg_cfgopen() to pcie_cfgregopen() and expose it to the
rest of the kernel. It now also accepts parameters via function
arguments rather than global variables.
- Add a notion of minimum and maximum bus numbers and reject requests for
an out of range bus.
- Add more range checks on slot/func/reg/bytes parameters to the cfg reg
read/write routines. Don't panic on any invalid parameters, just fail
the request (writes do nothing, reads return -1). This matches the
behavior of the other cfg mechanisms.
- Port the memory mapped configuration space access to amd64. On amd64
we simply use the direct map (via pmap_mapdev()) for the memory mapped
window.
- During acpi_attach() just after loading the ACPI tables, check for a
MCFG table. If it exists, call pciereg_cfgopen() on each subtable
(memory mapped window). For now we only support windows for domain 0
that start with bus 0. This removes the need for more chipset-specific
quirks in the MD code.
- Remove the chipset-specific quirks for the Intel 5000P/V/Z chipsets
since these machines should all have MCFG tables via ACPI.
- Updated pci_cfgregopen() to DTRT if ACPI had invoked pcie_cfgregopen()
earlier.
MFC after: 2 weeks
behavior. Specifically, probe Host-PCI bridges in the order they are
encountered in the tree. For CPUs, just use an order of 100000 and assume
that no Host-PCI bridges will be more than 10000 levels deep in the
namespace. This fixes an issue on some boxes where the HPET timer stopped
attaching.
assumptions about the state of the cooling devices. Instead, switch them
off on init and, only after that, we are in TZ_ACTIVE_NONE.
Submited by: Andriy Gapon <avg at icyb.net.ua>
Reviewed by: njl
different "platforms" on x86 machines. The existing code already handles
having two platforms: ACPI and legacy. However, the existing approach was
rather hardcoded and difficult to extend. These changes take the approach
that each x86 hardware platform should provide its own nexus(4) driver (it
can inherit most of its behavior from the default legacy nexus(4) driver)
which is responsible for probing for the platform and performing
appropriate platform-specific setup during attach (such as adding a
platform-specific bus device). This does mean changing the x86 platform
busses to no longer use an identify routine for probing, but to move that
logic into their matching nexus(4) driver instead.
- Make the default nexus(4) driver in nexus.c on i386 and amd64 handle the
legacy platform. It's probe routine now returns BUS_PROBE_GENERIC so it
can be overriden.
- Expose a nexus_init_resources() routine which initializes the various
resource managers so that subclassed nexus(4) drivers can invoke it from
their attach routine.
- The legacy nexus(4) driver explicitly adds a legacy0 device in its
attach routine.
- The ACPI driver no longer contains an new-bus identify method. Instead
it exposes a public function (acpi_identify()) which is a probe routine
that the MD nexus(4) drivers can use to probe for ACPI. All of the
probe logic in acpi_probe() is now moved into acpi_identify() and
acpi_probe() is just a stub.
- On i386 and amd64, an ACPI-specific nexus(4) driver checks for ACPI via
acpi_identify() and claims the nexus0 device if the probe succeeds. It
then explicitly adds an acpi0 device in its attach routine.
- The legacy(4) driver no longer knows anything about the acpi0 device.
- On ia64 if acpi_identify() fails you basically end up with no devices.
This matches the previous behavior where the old acpi_identify() would
fail to add an acpi0 device again leaving you with no devices.
Discussed with: imp
Silence on: arch@
the cpufreq drivers to reliably use properties of PCI devices for quirks,
etc.
- For the legacy drivers, add CPU devices via an identify routine in the
CPU driver itself rather than in the legacy driver's attach routine.
- Add CPU devices after Host-PCI bridges in the acpi bus driver.
- Change the ichss(4) driver to use pci_find_bsf() to locate the ICH and
check its device ID rather than having a bogus PCI attachment that only
checked for the ID in probe and always failed. As a side effect, you
can now kldload ichss after boot.
- Fix the ichss(4) driver to use the correct device_t for the ICH (and not
for ichss0) when doing PCI config space operations to enable SpeedStep.
MFC after: 2 weeks
Reviewed by: njl, Andriy Gapon avg of icyb.net.ua
the appropriate bit in the DEVACTB register.
This change allows the C2 state on those systems to work as expected.
Reviewed by: njl
Submitted by: Andriy Gapon <avg at icyb.net.ua>
MFC after: 1 week
spec:
- Use read/modify/write cycles to enable and disable the HPET instead of
writing 0 to reserved bits.
- Shutdown the HPET during suspend as encouraged by the spec.
- Fail to attach to an HPET with a period of zero.
MFC after: 1 week
PR: kern/119675 [3]
Reported by: Leo Bicknell | bicknell ufp.org
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
correct number of acpi_thermalX devices. Having this wrong caused the
acpi_thermal thread to realloc the array of devices on each loop iteration.
MFC after: 1 week
PR: kern/118497
Submitted by: Pasi Parviainen
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
CPUs to make sure idle threads are evicted from the softc before returning
from acpi_cpu_shutdown(). However, this is unnecessary since stop_cpus()
handles this for itself and at this point it's possible that our IPI will be
blocked (interrupts disabled).
Thanks to: Glen Leeder <glen.leeder / nokia.com>
MFC after: 3 days
reason (not all BIOSen have _DIS methods for all link devices for example).
This matches the behavior of attach() with respect to _DIS as well.
Submitted by: njl
handle to the PCI device_t if the ACPI device_t is already attached to a
driver. This happens on the Tablet TC1000 which for some reason includes
two PCI-ISA bridges and treats the second bridge as an ACPI system resource
device.
Reviewed by: njl (a while ago)
MFC after: 3 days
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
