o add channel flag to enable freq <-> ieee channel # mapping (can
go away in the future when ieee number is precomputed)
o add mapping between 900mhz freq's and channel #'s that gives a
unique channel # for each half/quarter/full width channel
o remove assumptions that half/quarter rate channels on happen in 11a
o remove assumptions that all 11g channels are full width
o ensure ic_curchan is reset on mode change so changing the channel
list (e.g. on countrycode change) doesn't leave curchan set to an
invalid channel
There is still an issue with switching rate sets; to be fixed separately.
MFC after: 1 month
only support external PHYs (besides not connectable internal ones
which respond at the usual addresses, but which don't hurt if we
let them show up) and don't wedge when isolating PHYs. Actually,
this change special cases limiting PHYs to Am79C97{3,5,8}, for
which this driver doesn't implement swiching between the internal
and external PHYs, yet, and Am79C971, where isolating the external
PHY (at least in case it's a DP83840A) wedges the chip. Together
with sys/dev/mii/acphy.c rev. 1.21 this adds support for the
100baseFX port of AT-2700 series adaptors, which use two AC101,
one for the copper and one for the fibre port (there might be
variants which only use one PHY though).
- Fix a bug in the previous revision that prevented the address of
the used (external) PHY to be actually recorded.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
MFC after: 1 week
bridge if it doesn't pass MSI messages up correctly. We set the flag
in pcib_attach() if the device ID is disabled via a PCI quirk.
- Disable MSI for devices behind the AMD 8131 HT-PCIX bridge. Linux has
the same quirk.
Tested by: no one despite repeated calls for testers
laptops.
Tested by: [1] Lion G. <liontanker@hotmail.com>
[2] Pietro Cerutti <pietro.cerutti@gmail.com>
Specialized mixer initialization for STAC9221, much like STAC9220.
Tested by: Devon H. O'Dell
- Set MIIF_NOLOOP as loopback doesn't work with this PHY. The MIIF_NOLOOP
flag currently triggers nothing but hopefully will be respected by
mii_phy_setmedia() later on.
- Use MII_ANEGTICKS instead of 5.
- Remove an unused macro.
- Fix some whitespace nits.
MFC after: 1 week
- In exphy_service() for the MII_TICK case don't bother to check whether
the currently selected media is of type IFM_AUTO as auto-negotiation
doesn't need to be kicked anyway.
- Remove #if 0'ed unapplicable code.
- Fix some whitespace nits.
MFC after: 1 week
and thus the FX_DIS pin indicates fibre media. This is part 1/2 of
adding support for the 100baseFX interface/port of AT-2700 series
adaptors.
Idea from: NetBSD
MFC after: 1 week
indices when manually adding media. Some of these I've missed while
converting drivers to take advantage of said fuctions recently,
others where longstanding bugs.
various types, as well as pipes and fifos for good measure. RELENG_6
currently passes all of these tests, but 7-CURRENT fails 0-byte writes
and sends on all stream socket types (and fifos, as they are based on
stream sockets).
Bumped into by: peter
Diagnosed by: jhb
Problem of: andre
- General style(9) cleanup -- white space, braces, line wraps, etc.
- Annotate a lack of synchronization the global route cache if the input
routine is invoked with parallelism.
- Remove unused debugging code.
routing:
- style(9) cleanup -- white space, braces, etc.
- Make include guards consistent with our more general naming
convention.
- Rearrange and complete forward structure declarations in at_extern.h,
remove testing of guards of various other include files to protect
function declarations.
This leaves an ifdef _KERNEL in at_var.h, but from inspection it seems
likely that this file is not actually safe for inclusion in user space
still. However, since it's not included from within src/ so this does
not appear to be an issue (ifconfig, etc, have migrated to the generic
cross-protocol ioctls for address operations).
etc, changes.
Remove a small amount of #if !defined(__FreeBSD__) code.
Add missing include guard for _NETATALK_AARP_H_.
Remove unneeded (and conflicting) extern prototype for aarptfree().
call, its semantics were unintentionally changed. It went from
returning the time state to returning 0 or -1. Since 0 means time
normal, and non-zero effectively only shows up around leap seconds,
this went unnoticed until now. At least unnoticed until someone was
trying to run a binary they didn't have source for and it was
misbehaving...
Submitted by: Judah Levine
MFC After: 2 weeks
members right. However, it also said it was aligned(1), which meant
that gcc generated really bad code. Mark this as aligned(4). This
makes things a little faster on arm (a couple percent), but also saves
about 30k on the size of the kernel for arm.
I talked about doing this with bde, but didn't check with him before
the commit, so I'm hesitant say 'reviewed by: bde'.
- Use printf() and device_printf() instead of log() in ichsmb(4).
- Create the mutex sooner during ichsmb(4) attach.
- Attach the interrupt handler later during ichsmb(4) attach to avoid
races.
- Don't try to set PCIM_CMD_PORTEN in ichsmb(4) attach as the PCI bus
driver does this already.
- Add locking to alpm(4), amdpm(4), amdsmb(4), intsmb(4), nfsmb(4), and
viapm(4).
- Axe ALPM_SMBIO_BASE_ADDR, it's not really safe to write arbitrary values
into BARs, and the PCI bus layer will allocate resources now if needed.
- Merge intpm(4) and intsmb(4) into just intsmb(4). Previously, intpm(4)
attached to the PCI device and created an intsmb(4) child. Now,
intsmb(4) just attaches to PCI directly.
- Change several intsmb functions to take a softc instead of a device_t
to make things simpler.
KERNBASE for the first 1 MB of RAM instead of calling pmap_mapdev().
pmap_mapdev() knows how to handle the first 1 MB (and has known for a
while now) and properly maps the memory as UC to boot.
MFC after: 2 weeks
