FDT-enabled targets were broken after r238043 that relies
on device up the hierarchy to properly setup interrupt.
nexus device for ARM platforms did job only partially:
setting handler but not unmasking interrupt. Unmasking
was performed by platform code.
Reviewed by: andrew@
the linker set of CPU modules. The newbus method, although clever,
had many flaws: it didn't really support multiple SoC, many of the
comments about order were just wrong, and it did a few things far too
late to be useful. delay and cpu_reset now work much earlier in the
boot process.
SoC variants. Fold the AT91SAM9XE chips into the AT91SAM9260
handling, where appropriate. The following SoCs/SoC families are recognized:
at91cap9, at91rm9200, at91sam9260, at91sam9261, at91sam9263,
at91sam9g10, at91sam9g20, at91sam9g45, at91sam9n12, at91sam9rl,
at91sam9x5
and the following variations are also recognized:
at91rm9200_bga, at91rm9200_pqfp, at91sam9xe, at91sam9g45, at91sam9m10,
at91sam9g46, at91sam9m11, at91sam9g15, at91sam9g25, at91sam9g35,
at91sam9x25, at91sam9x35
This is only the identification routine: no additional Atmel devices
are supported at this time.
# With these changes, I'm able to boot to the point of identification
# on a few different Atmel SoCs that we don't yet support using the
# KB920X config file -- someday tht will be an ATMEL config file...
compiled into the kernel. This allows us to boot the same kernel on
machines with different master clock frequencies, so long as we can
determine the main clock frequency accurately. Cleanup the pmc clock
init function so it can be called in early boot so we can use the
serial port just after we call cninit.
# We have two calls to at91_pmc_clock_init for reasons unknown, that will
# be fixed later -- it is harmless for now.
* Support for sam9 "EMAC" controller.
* Support for rmii interface to phy.
at91.c & at91sam9.c:
* Eliminate separate at91sam9.c file.
* Add new devices to at91sam9_devs table.
at91_machdep.c & at at91sam9_machdep.c:
* Automatic chip type determination.
* Remove compile time chip dependencies.
* Eliminate separate at91sam9_machdep.c file.
at91_pmc.c:
* Corrected support for all of the sam926? and sam9g20 chips.
* Remove compile time chip dependencies.
My apologies to Greg for taking so long to take care of it.
the implementation can guarantee forward progress in the event of
a stuck interrupt or interrupt storm. This is especially critical
for fast interrupt handlers, as they can cause a hard hang in that
case. When first called, arm_get_next_irq() is passed -1.
Obtained from: Juniper Networks, Inc.
operates in the common memory mode and use polling mode to control
the status of operations as I don't have any board with interrupt
line routed yet. I'll add the GPIO interrupt driven mode as soon
as I get one.
time constant. This allows us to potentially change it at runtime or
autodetect it early in the boot (the latter being much more likely to
have a good outcome).
memory allocation. It was change to include the range in the normal
memory area, so these ifdef'd out special cases are no longer useful
to keep around.
place to add this connection, since the interrupt is for a GPIO pin,
but since we have no alternative at the moment...
Submitted by: Hans Petter Selasky
interrupt. So, add a new function pointer, arm_post_filter, which defaults
to NULL, and which will be used as the post_filter arg for
intr_event_create(). Set it properly for the AT91, so that it boots again.
Reported by: hps
Add a new option, SKYEYE_WORKAROUNDS, which as the name suggests adds
workarounds for things skyeye doesn't simulate. Specifically :
- Use USART0 instead of DBGU as the console, make it not use DMA, and manually provoke an interrupt when we're done in the transmit function.
- Skyeye maintains an internal counter for clock, but apparently there's
no way to access it, so hack the timecounter code to return a value which
is increased at every clock interrupts. This is gross, but I didn't find a
better way to implement timecounters without hacking Skyeye to get the
counter value.
- Force the write-back of PTEs once we're done writing them, even if they
are supposed to be write-through. I don't know why I have to do that.
o Add memory barrier to bus space
o Allow for up to 3 IRQs per device
o Move to table driven population of children devices.
o Add support for usb ohci memory mapped controller resource allocation.
o Clean up a bunch of extra writes to disable interrupts that are now
done elsewhere.
o Force all system interrupt handlers be fast. We get deadlock if they
aren't.
is a ARM920T based CPU with a bunch of built-in peripherals. The
inital import supports the SPI bus, the TWI bus (although iicbus
integration is not complete), the uarts, the system timer and the
onboard ethernet. Support for the Kwikbyte KB9202
(http://www.kwikbyte.com) board is also included, although there's no
reason why the 9200 and the 9201 wouldn't also work. Primitive
support for running under the skyeye emulator is also provided
(although skyeye's support for the AT91RM9200 is a little weak).
The code has been structured so that other members of Atmel's arm family can
be supported in the future. The AT91SAM9260 is not presently supported
due to lack of hardware. The arm7tdmi families are also not supported
becasue they lack an MMU.
Many thanks to cognet@ for his help and assistance in bringing up this
board. He did much of the vm work and wrote parts of the uart and
system timer code as well as the bus space implementation.
The system boots to single user w/o problem, although the serial
console is a little slow and the ethernet driver is still in flux.
This work was sponsored by Timing Solutions, Corporation. I am
grateful to their support of the FreeBSD project in this manner.
