not blocked by raising the pil, a reciever may be interrupted while holding
a spinlock. If the sender does not defer interrupts throughout the entire
operation it may be interrupted and try to acquire a spinlock held by a
reciever, leading to a deadlock due to the synchronization used by the
ipi handlers themselves.
Submitted by: tmm
Instead of caching the ucred reference, just go ahead and eat the
decerement and increment of the refcount. Now that Giant is pushed down
into crfree(), we no longer have to get Giant in the common case. In the
case when we are actually free'ing the ucred, we would normally free it on
the next kernel entry, so the cost there is not new, just in a different
place. This also removse td_cache_ucred from struct thread. This is
still only done #ifdef DIAGNOSTIC.
Tested on: i386, alpha
the user mappings from the tlb due to the context numbers rolling over. The
store to the internal mmu register must be followed by a membar #Sync before
much else happens to "avoid data corruption", so we use special inlines which
both disable interrupts and ensure that the compiler will not insert extra
instructions between the two. Also, load the tte tag and check if the context
is nucleus context, rather than relying on the priviledged bit which doesn't
actually serve any purpose in our design, and check the lock bit too for
sanity.
wait for those cpus, instead of all of them by using a count. Oops.
Make the pointer to the mask that the primary cpu spins on volatile, so
gcc doesn't optimize out an important load. Oops again.
Activate tlb shootdown ipi synchronization now that it works. We have
all involved cpus wait until all the others are done. This may not be
necessary, it is mostly for sanity.
Make the trigger level interrupt ipi handler work.
Submitted by: tmm
the number of physical pages per KVA page allocated scales properly with
memory size. This fixes problems with kmem_map being too small.
Noticed by: mike, wollman
Submitted by: tmm
o In i386's <machine/endian.h>, macros have some advantages over
inlines, so change some inlines to macros.
o In i386's <machine/endian.h>, ungarbage collect word_swap_int()
(previously __uint16_swap_uint32), it has some uses on i386's with
PDP endianness.
Submitted by: bde
o Move a comment up in <machine/endian.h> that was accidentially moved
down a few revisions ago.
o Reenable userland's use of optimized inline-asm versions of
byteorder(3) functions.
o Fix ordering of prototypes vs. redefinition of byteorder(3)
functions, so that the non-GCC (libc asm) case has proper
prototypes.
o Add proper prototypes for byteorder(3) functions in <sys/param.h>.
o Prevent redundant duplicate prototypes by making use of the
_BYTEORDER_PROTOTYPED define.
o Move the bswap16(), bswap32(), bswap64() C functions into MD space
for platforms in which asm versions don't exist. This significantly
reduces the complexity of some things at the cost of duplicate code.
Reviewed by: bde
than the other implementations; we have complete control over the tlb, so we
only demap specific pages. We take advantage of the ranged tlb flush api
to send one ipi for a range of pages, and due to the pm_active optimization
we rarely send ipis for demaps from user pmaps.
Remove now unused routines to load the tlb; this is only done once outside
of the tlb fault handlers.
Minor cleanups to the smp startup code.
This boots multi user with both cpus active on a dual ultra 60 and on a
dual ultra 2.
Due to allocating tlb contexts on the fly, we only ever need to demap the
primary context, non-primary contexts have already been implicitly flushed
by context switching. All we really need to tell is if its a kernel demap
or not, and its easier just to compare against the kernel_pmap which is a
constant.
the context is not actually stolen, as it would be for i386. Instead of
deactivating a user vmspace immediately when switching out, and recycling
its tlb context, wait until the next context switch to a different user
vmspace. In this way we can switch from a user process to any number of
kernel threads and back to the same user process again, without losing any
of its mappings in the tlb that would not already be knocked by the automatic
replacement algorithm. This is not expected to have a measurable performance
improvement on the machines we currently run on, but it sounds cool and makes
the sparc64 port SMPng buzz word compliant.
on the loader to do it. Improve smp startup code to be less racy and to
defer certain things until the right time. This almost boots single user
on my dual ultra 60, it is still very fragile:
SMP: AP CPU #1 Launched!
Enter full pathname of shell or RETURN for /bin/sh:
# ls
Debugger("trapsig")
Stopped at Debugger+0x1c: ta %xcc, 1
db> heh
No such command
db>
with pmaps. When the context numbers wrap around we flush all user mappings
from the tlb. This makes use of the array indexed by cpuid to allow a pmap
to have a different context number on a different cpu. If the context numbers
are then divided evenly among cpus such that none are shared, we can avoid
sending tlb shootdown ipis in an smp system for non-shared pmaps. This also
removes a limit of 8192 processes (pmaps) that could be active at any given
time due to running out of tlb contexts.
Inspired by: the brown book
Crucial bugfix from: tmm
clobbered by the child. This is more complicated than usual because the
window that could get clobbered is pushed in kernel mode, so a lot of
registers would have to be saved in other registers in userland and we
don't have enough. What we do have is space in the pcb to temporarily
store user windows that were spilled in kernel mode, but could not be
immediately stored to the user stack. So we copy in the parent's topmost
window and save it in the pcb, and arrange for it to be copied back out
when the child is done frobbing the stack.
Reviewed by: tmm
Previously, the UPAGES/KSTACK area of processes/threads would leak memory
at the time that a previously swapped process was terminated. Lukcily, the
leak was only 12K/proc, so it was unlikely to be a major problem unless you
had an undersized swap partition.
Submitted by: dillon
Reviewed by: silby
MFC after: 1 week
In order to determine what to page out, the vm_daemon checks
reference bits on all pages belonging to all processes. Unfortunately,
the algorithm used reacted badly with shared pages; each shared page
would be checked once per process sharing it; this caused an O(N^2)
growth of tlb invalidations. The algorithm has been changed so that
each page will be checked only 16 times.
Prior to this change, a fork/sleepbomb of 1300 processes could cause
the vm_daemon to take over 60 seconds to complete, effectively
freezing the system for that time period. With this change
in place, the vm_daemon completes in less than a second. Any system
with hundreds of processes sharing pages should benefit from this change.
Note that the vm_daemon is only run when the system is under extreme
memory pressure. It is likely that many people with loaded systems saw
no symptoms of this problem until they reached the point where swapping
began.
Special thanks go to dillon, peter, and Chuck Cranor, who helped me
get up to speed with vm internals.
PR: 33542, 20393
Reviewed by: dillon
MFC after: 1 week
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
work loads. It tapers off after that as gcc's working set generally just fits.
compiling bin/csh:
TSB_PAGES = 2
213.33 real 77.59 user 110.01 sys
TSB_PAGES = 4
116.43 real 75.78 user 19.16 sys
TSB_PAGES = 8
119.27 real 76.38 user 18.12 sys
Testing by: tmm
due to them being faster in certain cases. Therefore we need to save
and restore the v8 %y register around traps in kernel mode as well as
traps in usermode.
Tested by: obrien, tmm
until we do some testing to see what's best. This gives a massive reduction
in system time for processes with a relatively large working set. The size
of the tsb directly affects the rss size that a user process can keep mapped.
When it starts to get full replacements occur and the process takes a lot of
soft vm faults. Increasing the default from 1 page to 2 gives the following
before and after numbers for compiling vfs_bio.c:
before:
14.27 real 6.56 user 5.69 sys
after:
8.57 real 6.11 user 1.62 sys
This should make self hosted builds more tolerable.
I don't believe anyone is quite using the sparc64 kernel sources in CVS
yet -- things aren't just quite ready (but almost). So this commit should
be OK to make.
window to the user stack while in a nested kernel trap. We do this for
entry to the kernel from user mode, but if we get an interrupt in kernel
mode while there are still user windows in the cpu, and we attempt to spill
to the user stack, we may take too many nested traps and overflow the trap
stack, causing a red state exception. This is needed by upcoming changes
to allow the user tsb to not be locked in the tlb.
Reviewed by: tmm
virtual page number in a much more convenient way; all in one piece. This
greatly simplifies the comparison for a matching tte, and allows the fault
handlers to be much simpler due to not having to load wierd masks.
Rewrite the tlb fault handlers to account for the new format. These are also
written to allow faults on the user tsb inside of the fault handlers; the
kernel fault handler must be aware of this and not clobber the other's
registers. The faults do not yet occur due to other support that is needed
(and still under my desk).
Bug fixes from: tmm
Most of the contents are commented out as they are as-yet untested.
However, I wanted the contents to match our other arches, so that when
people make changes to {i386,alpha,ia64}, they will also make the same
changes here.
pmap_qenter and pmap_qremove in preference to pmap_kenter/pmap_kremove.
The former maps in multiple pages at a time, and so can do a ranged
flush. Don't assume that pmap_kenter and pmap_kremove will flush the tlb,
even though they still do. It will not once the MI code is updated to use
pmap_qenter and pmap_qremove.
will be used to reduce the number of tlb shootdown ipis in an smp system
by sending one ipi for a whole range of pages, instead of one per page.
Munge the context demap operations slightly to support demapping a non-primary
context.
If we don't do this here there's a 1 instruction race where an interrupt
could come in and crash the user process due to having no stack.
2. Pass %fsr to the user trap handler in %l4. Since %fsr can only be loaded
from or stored to memory, we need to do some contortions and temporarily
save it to the alternate global stack.
3. Reload the pcb and pcpu registers for traps in kernel mode, for sanity.
Submitted by: tmm (1, 2)
While in userland, keep the thread's ucred reference in a shadow
field so that the usual place to store it is NULL.
If DIAGNOSTIC is not set, the thread ucred is kept valid until the next
kernel entry, at which time it is checked against the process cred
and possibly corrected. Produces a BIG speedup in
kernels with INVARIANTS set. (A previous commit corrected it
for the non INVARIANTS case already)
Reviewed by: dillon@freebsd.org
deprecated in favor of the POSIX-defined lowercase variants.
o Change all occurrences of NTOHL() and associated marcros in the
source tree to use the lowercase function variants.
o Add missing license bits to sparc64's <machine/endian.h>.
Approved by: jake
o Clean up <machine/endian.h> files.
o Remove unused __uint16_swap_uint32() from i386's <machine/endian.h>.
o Remove prototypes for non-existent bswapXX() functions.
o Include <machine/endian.h> in <arpa/inet.h> to define the
POSIX-required ntohl() family of functions.
o Do similar things to expose the ntohl() family in libstand, <netinet/in.h>,
and <sys/param.h>.
o Prepend underscores to the ntohl() family to help deal with
complexities associated with having MD (asm and inline) versions, and
having to prevent exposure of these functions in other headers that
happen to make use of endian-specific defines.
o Create weak aliases to the canonical function name to help deal with
third-party software forgetting to include an appropriate header.
o Remove some now unneeded pollution from <sys/types.h>.
o Add missing <arpa/inet.h> includes in userland.
Tested on: alpha, i386
Reviewed by: bde, jake, tmm
patch from a year ago: give file flags their own type. This does not
(yet) change the type used by system calls or library functions.
The underlying type was chosen to match what is returned by stat().
support for managing both streaming caches on psycho pairs).
Use explicit bus space accesses instead of mapping the device memory into
kva.
Move DVMA allocation to the map creation/dma memory allocation functions.
disable interrupts completely, and stxa_sync(), which performs a store
immediately followed by a membar #Sync with interrupts disabled (this
is needed for writes to diagnostic registers).
this is a low-functionality change that changes the kernel to access the main
thread of a process via the linked list of threads rather than
assuming that it is embedded in the process. It IS still embeded there
but remove all teh code that assumes that in preparation for the next commit
which will actually move it out.
Reviewed by: peter@freebsd.org, gallatin@cs.duke.edu, benno rice,
some arches and the syscall table is machine-independent. It was
(bogusly) conditional on COMPAT_43, so this usually makes no difference.
ia64: in addition:
- replace the bogus cloned comment before osigreturn() by a correct one.
osigreturn() is just a stub fo ia64's.
- fix the formatting of cloned comment before sigreturn().
- fix the return code. use nosys() instead of returning ENOSYS to get
the same semantics as if the syscall is not in the syscall table.
Generating SIGSYS is actually correct here.
- fix style bugs.
powerpc: copy the cleaned up ia64 stub. This mainly fixes a bogus comment.
sparc64: copy the cleaned up the ia64 stub, since there was no stub before.
cpu(s) into the kernel, and sync-ing them up to "kernel" mode so we can
send them ipis, which also work.
Thanks to John Baldwin for providing me with access to the hardware
that made this possible.
Parts obtained from: bsd/os
Call critical_enter/critical_exit around (fast) interrupt handlers. All
non-threaded interrupts are fast, and the threaded interrupt scheduler is
itself a fast interrupt.
Assert that an interrupt handler we are about to call is non-zero.
Be paranoid about restoring the users global registers. Do it as the
last thing before switching to alternate globals (when we magically get
our preloaded registers back), and do it with interrupts disabled. Any
kind of kernel trap when the globals are not setup properly is bad news.
Don't save and restore the kernel g6, it invariably points to the current
pcb now.
data word in an interrupt packet is non-zero, it points to code to execute
to handle the ipi, so jump to it instead of enqueueing the packet. It
is unclear if we will need queued ipis.
Interrupt g7 now points to pcpu, instead of to the per-cpu interrupt queue
itself, so use that instead. Interrupt g6 is no longer reserved.
parameters needed for smp support.
If we are not the boot processor, jump to the smp startup code instead.
Implement a per-cpu panic stack, which is used for bootstrapping both
primary and secondary processors and during faults on the kernel stack.
Arrange the per-cpu page like the pcb, with the struct pcpu at the end
of the page and the panic stack before it.
Use the boot processor's panic stack for calling sparc64_init.
Split the code to set preloaded global registers and to map the kernel
tsb out into functions, which non-boot processors can call.
Allocate the kstack for thread0 dynamically in pmap_bootstrap, and give
it a guard page too.
to the current pcb.
Remove interrupt global defines; they use PCPU_REG now.
Move ATOMIC_INC_INT here from exception.s, add ATOMIC_DEC_INT.
Add a KASSERT macro for use in assembler.
substantial fraction of the number of entries of tte's in the tsb
would need to be looked up, traverse the tsb instead. This is crucial
in some places, e.g. when swapping out a process, where a certain
pmap_remove() call would take very long time to complete without this.
2. Implement pmap_qenter_flags(), which will become used later
3. Reactivate the instruction cache flush done when mapping as executable.
This is required e.g. when executing files via NFS, but is known to
cause problems on UltraSPARC-IIe CPU's. If you have such a CPU, you
will need to comment this call out for now.
Submitted by: jake (3)
struct ofw_nexus_reg. Implement UPA device memory management in the
nexus driver.
Adapt the psycho driver to these changes, and do some minor cleanup work
while being there.
for certain user pages, stores to kernel pages would not update the
affected cache lines, which would sometimes cause the wrong data to be
returned for loads from kernel pages. This was especially fatal when
the addresses affected held the kernel stack pointer, and a random
value was loaded into it.
Fix a harmless off by one error in a dcache_inval_phys call.
Fix a potential race in setting up the per-cpu pointer if the special
restore fails on return to user mode fails and we need to trap back
into the kernel to fault in more stack.
Remove debug code.
an efficient way for the kernel to bounce certain mundane traps back to
userland for handling there. A user trap handler returns directly to the
trapping user code, rather than going through the kernel again. Only a
handful of instructions are actually executed in kernel mode.
Implement sysarch(SPARC_UTRAP_INSTALL).
Add code to handle sharing of the user trap table across forks and unsharing
at exec.
This can be used to implement efficient tracking of floating point register
usage in userland, fe by a thread library, and to handle alignment fault
fixups and instruction emulation in userland, for which the code may need
to be different for 32bit and 64bit binaries.
something wrong with the kernel stack.
Add code to check the kernel stack pointer in various important places
and try hard not to go down in flames if its wrong.
