there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
The lun is not incremented in the ata-disk driver when ATA_STATIC_ID
is not defined, thanks to Kenneth Wayne Culver <culverk@wam.umd.edu>
for finding that one.
PHK pointed at the & problem in atapi-cd in devstat_end_transaction_buf.
Too little sleep I guess...
Phase 1) move the driver
Phase 2)
Phase 3) Profit, by splitting the driver into smaller files like
bktr_tuner, bktr_card, bktr_audio, bktr_<osname>
making it easier to maintain and understand.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
usually cleared by a successful selection, but there is no guarantee
that a future successful selection will ever occur (e.g. empty bus).
The driver never looks at SELINGO, but the busy LED does, so this
change has the cosmetic effect of fixing the rare instance where the
busy LED was left on, confusing the user.
aic7xxx parts. This problem could result in data corruption
during periods of my PCI bus load by busmasters other than the
aic7xxx.
Many thanks to Andrew Gallatin <gallatin@cs.duke.edu> for characterizing
the symptoms of this problem and testing this fix.
adjust the bp->b_bcount the same way for unlabeled VN access as dscheck
does for labeled access.
We also increase the block size to at least 8K for efficiency.
Reviewed by: Tor.Egge@fast.no
- Remove sc_get_scr_stat(). It's not necessary anymore.
- Call ttymalloc() to allocate the struct tty for each vty, rather than
statically declaring an array of struct tty. We still need a statically
allocated struct tty for the first vty which is used for the kernel
console I/O, though.
- Likewise, call ttymalloc() for /dev/sysmouse and /dev/consolectl.
- Delete unnecessary test on the pointer struct tty *tp in some functions.
- Delete unused code in scmouse.c.
WARNING: this change requires you to recompile screen savers!
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
Bug fix: xmradio nolonger experiences a 6Mhz offset after running FXTV
New feature: Automatic Tuner selection for AVerMedia cards with
configuration EEPROMs on (ie the Bt878 based cards)
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
PR: 13793
size != 512 that are configured without a label. The bug should only
have effected swap-backed VN mounts without a label.
Add several major features to VN. In the kernel we add a swap
pre-reservation capability, which can be used to guarentee seek
consistency for swap-backed VN nodes. This also incidently allows
a swap-backed VN filesystem to be recovered after a crash in some
cases (if the same swap blocks happen to be reserved).
We also add a number of new options to vnconfig which do the work
of pre-zeroing or creating/truncating/extending a file which greatly
simplifies using VN in a file-backed configuration.
Add FreeBSD CVS label to sys/sys/vnioctl.h, as well as a new ioctl
flag for the swap pre-reservation feature.
Reviewed by: Alan Cox <alc@cs.rice.edu>, David Greenman <dg@root.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
I have an 82559 card with the same id as the other 8255[78] chips, but
that was made with a date code of 0699 (June 99). The submitter shows
this working with the probe etc, but doesn't actually say it works as
on the ethernet. :-) Assuming it does, this is a RELENG_3 merge candidate.
Submitted by: Steven E Lumos <slumos@sam.ISRI.UNLV.EDU>
this PHY and the Davicom DM9101 have exactly the same register definitions.
One of them is probably a clone of the other. I'm not sure which.
This is needed for the Davicom DM9102 10/100 PCI ethernet driver which
will be committed shortly.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
MCA SCSI adapters.
bt_mca.c is going to live in sys/dev/buslogic instead of sys/dev/mca
as per a conversation with Peter, Doug and Mike.
Thanks to Andy Farkas <andyf@speednet.com.au> for being such a good
sport and doing all the testing for me (as I don't actually own one
of these cards. Yet.)
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Fix a bug where video capture locks up on channel changes.
Many thanks to Juha for solving this.
Submitted by: Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
New Features:
Greatly improved VBI capture support. (mainly for the AleVT port)
Supports select() on /dev/vbi
Improved RISC program for RGB+VBI capture to capture both evenodd
VBI data even when only capturing even only (or odd only) video
Based on code from Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Support for Hauppauge 627 and Temic 4006
Submitted by: Maurice Castro <maurice@atum.castro.aus.net>
Bug Fix:
Fix bug in AverMedia card detection.
Break out the detection logic for the aic7855 and properly report
these chips as 7855s instead of 7850s.
The 2940AU_CN is an aic7860 based card, not aic7860.
Not setting CACHETHEN turned out to be a bad idea. It can cause
spurious corruption under heavy PCI load with multiple masters.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best.
Use the specfs routines rather having cloned copies in devfs.
ones were made by Lucent). The Broadcom chip also appears to use an
internal PHY made by Broadcom which uses the Broadcom OUI. This is different
from previous ASICs which always returned 0 in the PHY ID registers.
To account for this, I added the necessary ID values for the Broadcom
PHY so that it can be detected and attached using the 3Com PHY driver
instead of defaulting to the generic one.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
some swapper problems analogous to those experienced with ccd.
This fix is a kludge: since we currently don't track the "sector size"
in a volume label, we guess a worst case (4 kB, as used by vnode
devices). If the concept of sector size is here to stay, I'll make
some changes to track the "sector size" of a volume. This will
probably be the maximum of the sector sizes of all component drives,
but things could get ugly if we start allowing non-standard sector
sizes such as 524 bytes.
Unkludged-version-submitted-by: phk
ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is
a port of the NetBSD driver with various hacks. The ML driver is necessary
to support the Olicom OC-2326 ThunderLAN-based NIC.
Also regenerated miidevs.h to pick up the proper 'obtained from'
revision string.
lockrange: correctly expand rangelock struct, including expanding a
null struct. Previously lockrange would attempt to lock a
NULL pointer under these circumstances.
Reported-by: Ian Freislich <iang@uunet.co.za>
initialized subdisks.
Tidy up some comments.
Eliminate sddownstate(); it wasn't being used any more. Return
REQUEST_DOWN instead.
Add setstate_by_force() to implement the VINUM_SETSTATE_FORCE ioctl
for diddling individual object states. This is a repair tool which
can also be used for panicing the system. Use with utmost care if at
all.
avoids a race condition where multiple RAID-5 subdisks are being
revived at the same time. The locks should also prevent conflicts
with user requests on concatenated and striped plexes, but this needs
more work.
Tidy up some comments.
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
instead, use generic entry points for all drivers.
- Eliminate bogus makedev().
- Eliminate softc in the lower drivers, as it is no longer necessary.
Submitted (95%) by: phk
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
Notice that 'unit' wasn't defined once I changed the parameters of the func.
These things make me feel like wading in with a flamethrowr or something.
Too much cruft!
</rant>
if_init_f_t is passed void * containing the address of ifp->if_softc
not the unit number.
Someone tell me if these things don't work as I don't have the hardware
needed to test them. (thats a first.)
I'll get if_ze and if_zp later.
Pointed out by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
to achieve a delay is pretty mean.
Andrew reports:
"The tulip_delay_300ns() is, well, bloody stupid on machines with a
heavily loaded PCI bus. It tries to do a delay by assuming PCI reads
will take a certain amount of time & issues a large amount of
(expensive, 5% CPU when your PCI bus is heavily loaded) pci reads.
Locally, we've replaced the calls to tulip_delay_300ns(sc) in the EMIT
macros with a simple DELAY(1) and not seen any problems. Plus we've
gained about 50Mb/sec throughput on our gigabit network cards because
of the added PCI bus bandwidth available."
Also, I do not understand why, but this change appears to stop the
Transmit Fifo underrun on one of my systems (but not the Alpha PC164SX).
This shouldn't make that much of a difference since the mii bus isn't
touched all that often, but perhaps when it does get accessed and hence
hammers the register, it was causing the chip to get upset.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
