the mfi(4) LSI MegaSAS RAID card. Looking at the Linux driver for the
mpt(4) it should be 0x0062 and not 0x0060. Tested with an mfi card
of this device id.
Approved by: re (bmah)
Reviewed by: scottl
MFC after: 3 days
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- duplicate #define in header, thanks to Kevin Lo for pointing out.
- incorrect BUSMASTER enable logic, thanks Patrick Oeschger
- 82543 fails due to bogus IO BAR logic
- Allow 82571 to use MSI interrupts
- Checksum Offload for UDP not working on 82575
Approved by:re
ioctl().
Note that other information provided by ifconfig(8) such like "list chan"
or "list ap" are still not available at this moment.
Before an(4) is connected to wlan(4), users are encouraged to use
ancontrol(8) to retrieve aforementioned information.
Reported by: dhw (http://lists.freebsd.org/pipermail/freebsd-current/2007-July/074848.html)
Reviewed by: ambrisko
Tested by: dhw
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
Both WWNN and WWPN are 64-bit unsigned integers and they are prefixed
with "0x", which requires two more bytes each.
Submitted by: Danny Braniss (danny at cs dot huji dot ac dot il)
via Matthew Jacob (lydianconcepts at gmail dot com)
Approved by: re (bmah)
MFC after: 3 days
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
on an down mxge interface
- Fix a bug where mxge reported the link state as
active when it wasn't (after ifconfig down).
- Prevent spurious watchdog resets when link partner is not consuming
- Add support for CX4 and popular XFP media detection
- Update the firmware and associated header files to 1.4.25
Approved by: re (kensmith)
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
Without this the PHY wouldn't work as expected. This should fix
dual-boot Windows XP machine where RealTek Windows drivers put the
PHY in power down mode during shutdown. The magic PHY register
accesses come from RealTek driver. No datasheets mention the magic
PHY registers.
In general, the PHY wakeup code should go into PHY driver. However it
seems that it only apply to RTL8169S single chip and it would be
another hack if we have rgephy(4) check what parent driver/chip model
is attached.
Reported by: lofi, Laurens Timmermans ( laurens AT timkapel DOT nl )
Tested by: lofi
Obtained from: RealTek FreeBSD driver
Approved by: re (Ken Smith)
- Don't leak the config lock if detach() fails due to the controller char
dev being open.
- Close a race between detach() and a process opening the controller char
dev.
MFC after: 1 week
Approved by: re (bmah)
Fix a resource allocation bug (explained by jhb on -acpi)
Thanks for Mike Tancsa for testing and helping track down the bug.
Approved by: re (kensmith)
MFC after: 3 weeks
detailed status on each of the backing subdisks. This allows userland
to see which subdisks are online, failed, missing, or a hot spare.
MFC after: 1 week
Approved by: re (bmah)
Reviewed by: sos
differ in their details with calls to a new function, ehci_hcreset(),
that performs the reset.
The original sequences either had no delay or a 1ms delay between
telling the controller to stop and asserting the controller reset
bit. One instance of the original reset sequence waited for the
controller to indicate that its reset was complete before continuing,
but the other two immediately let the subsequent code execute. The
latter is a problem on some hardware, because a read of the HCCPARAMS
register returns an incorrect value while the reset is in progress,
which triggers an infinite loop in ehci_pci_givecontroller(), which
hangs the system on shutdown.
The reset sequence in ehci_hcreset() starts with the most complete
instance from the original code, which contains a loop to wait for
the controller to indicate that its reset is complete. This appears
to be the correct thing to do according to "Enhanced Host Controller
Interface Specification for Universal Serial Bus" revision 1.0,
section 2.3.1. Add another loop to wait for the controller to
indicate that it has stopped before setting the HCRESET bit. This
is required by the section 2.3.1 in the specification, which says
that setting HCRESET before the controller has halted "will result
in undefined behaviour".
Reviewed by: imp (previous patch version without the extra wait loop)
Tested by: se (previous patch version without the extra wait loop)
Approved by: re (bmah)
MFC after: 1 week
previously conditionally acquired Giant based on debug.mpsafenet. As that
has now been removed, they are no longer required. Removing them
significantly simplifies error-handling in the socket layer, eliminated
quite a bit of unwinding of locking in error cases.
While here clean up the now unneeded opt_net.h, which previously was used
for the NET_WITH_GIANT kernel option. Clean up some related gotos for
consistency.
Reviewed by: bz, csjp
Tested by: kris
Approved by: re (kensmith)
requiring DC_TX_ALIGN or DC_TX_COALESCE, which was previously done
in dc_start_locked(), into dc_encap().
o In dc_encap():
- If m_defrag() fails just drop the packet like other NIC drivers
do. This should only happen when there's a mbuf shortage, in which
case it was possible to end up with an IFQ full of packets which
couldn't be processed as they couldn't be defragmented as they
were taking up all the mbufs themselves. This includes adjusting
dc_start_locked() to not trying to prepend the mbuf (chain) if
dc_encap() has freed it.
- Likewise, if bus_dmamap_load_mbuf() fails as dc_dma_map_txbuf()
failed, free the mbuf possibly allocated by the above call to
m_defrag() and drop the packet.
o In dc_txeof():
- Don't clear IFF_DRV_OACTIVE unless there are at least 6 free TX
descriptors. Further down the road dc_encap() will bail if there
are only 5 or fewer free TX descriptors, causing dc_start_locked()
to abort and prepend the dequeued mbuf again so it makes no sense
to pretend we could process mbufs again when in fact we won't.
While at it replace this magic 5 with a macro DC_TX_LIST_RSVD.
- Just always assign idx to sc->dc_cdata.dc_tx_cons; it doesn't
make much sense to exclude the idx == sc->dc_cdata.dc_tx_cons
case.
o In dc_dma_map_txbuf() there's no need to set sc->dc_cdata.dc_tx_err
to error if the latter is != 0, bus_dmamap_load_mbuf() already
returns the same error value in that case anyway.
o For less overhead, convert to use bus_dmamap_load_mbuf_sg() for
loading RX buffers.
o Remove some banal and/or outdated comments.
Approved by: re (kensmith)
MFC after: 1 week
to clear RL_TDESC_VLANCTL_TAG). This fixes sending packets in the
native VLAN when running both tagged and an untagged VLAN over the
same trunk and descriptors are recycled.
Approved by: re (kensmith)
MFC after: 1 week
that could cause panics and corruption under moderate load. Many thanks
to Matt Reimer, Tom McDonald, and the rest of the guys at VPOP.net for
their help in identifying and testing this.
Approved by: re
errors (especially when jumbo frames are enabled or in low memory systems)
because the RX chain was corrupted when an mbuf was mapped to an unexpected
number of buffers.
- Fixed a problem that would cause kernel panics when an excessively
fragmented TX mbuf couldn't be defragmented and was released by
bce_tx_encap().
Approved by: re(hrs)
MFC after: 7 days
the fast or safe/slow method is in use. Fast remains at 1000, slow is
now at 850 (always preferred to TSC). Since the HPET has proven slower
than ACPI-fast on some systems, drop its quality to 900. In the future,
it is hoped that HPET performance will improve as it is the main
timer Intel supports. HPET may move back to 2000 in -current once RELENG_7
is branched to ensure that it gets tested.
Approved by: re
the duration of the function. The device we would otherwise
have left in an useless state may just as well be the low-level
console. When booting verbose, we do need it addressable if we
want to avoid a MCA.
Approved by: re (kensmith)
framework for non-MPSAFE network protocols:
- Remove debug_mpsafenet variable, sysctl, and tunable.
- Remove NET_NEEDS_GIANT() and associate SYSINITSs used by it to force
debug.mpsafenet=0 if non-MPSAFE protocols are compiled into the kernel.
- Remove logic to automatically flag interrupt handlers as non-MPSAFE if
debug.mpsafenet is set for an INTR_TYPE_NET handler.
- Remove logic to automatically flag netisr handlers as non-MPSAFE if
debug.mpsafenet is set.
- Remove references in a few subsystems, including NFS and Cronyx drivers,
which keyed off debug_mpsafenet to determine various aspects of their own
locking behavior.
- Convert NET_LOCK_GIANT(), NET_UNLOCK_GIANT(), and NET_ASSERT_GIANT into
no-op's, as their entire behavior was determined by the value in
debug_mpsafenet.
- Alias NET_CALLOUT_MPSAFE to CALLOUT_MPSAFE.
Many remaining references to NET_.*_GIANT() and NET_CALLOUT_MPSAFE are still
present in subsystems, and will be removed in followup commits.
Reviewed by: bz, jhb
Approved by: re (kensmith)
- make NDIS_DEBUG a sysctl
- default to IEEE80211_MODE_11B if the card doesnt tell us the channels
- dont mess with ic_des_chan when we assosciate
- Allow a directed scan by setting the ESSID before scanning (verified
with wireshark). Hidden APs probably wouldnt have worked before.
- Grab the channel type and use it to look up the correct curchan for
the scan results (mistakenly used 11B before)
- Fix memory leak in the ndis_scan_results
Tested by: matteo
Reviewed by: sam
Approved by: re (rwatson)
to repeat if you had more than two keys down at any given time (which
happened to me all the time with emacs).
This is taken from PR 110681, although what URATAN Shigenobu describes
there is different than the pathology that I have been seeing. I'm
seeing this only in X, while he sees it on his console, yet I think
the two problems are related. I've also reworked the patch slightly
to conform to the coding standards of adjacent code.
It is unclear to me if this merely masks the maddening bug that I have
seen, or if this is a real fix. I typically see the problem when I'm
typing fast in emacs and using lots of motion keys (meta and control).
In either case, my workstation at work again is finally useful with
this patch.
PR: 110681
Submitted by: URATAN Shigenobu
Approved by: re (blanket)
the protocol to be report on each open, but ignore any errors as set
protocol for mice that don't implement the boot protocol can generate
an error. Evidentally, the Gyration GyroPoint RF Technology Receiver
(Gyration Ultra Cordless) device has this problem.
Submitted by: Eugene M. Kim
PR: 106565
Approved by: re (blanket)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
Ever since switching to adaptive polling re(4) occasionally spews
watchdog timeouts on systems with MSI capability. This change is
minimal one for supporting MSI and re(4) also needs MSIX support
for RTL8111C in future. Because softc structure of re(4) is shared
with rl(4), rl(4) was touched to use the modified softc.
Reported by: cnst
Tested by: cnst
Approved by: re (kensmith)
Because nfe(4) hardware doesn't support SG on Rx path, supporting
jumbo frame requires very large contiguous kernel memory(i.e. several
mega bytes). In case of lack of contiguous kernel memory that
allocation request may always fail. However nfe(4) can operate on normal
sized MTU frames, so go ahead and just disable jumbo frame support.
While I'm here add a new tunable "hw.nfe.jumbo_disable" to disable
jumbo frame support.
In nfe_poll, make sure to invoke correct Rx handler.
Approved by: re (kensmith)
advancing. Read from the timer before attaching to be sure it advances
in 1 us. Since the slowest rate allowed by the spec is 10 MHz, the
timer is guaranteed to change in this interval if it is working.
Tested by: Rui Paulo
Approved by: re
MFC after: 3 days
4KB pages as i386, data structures that just fit in one page on i386 (and
on 64 bit architectures with 8KB pages) can be distributed over two pages
on amd64. This is a porblem in the case of the Symbios driver, since the
SCRIPTS engine in the SCSI chip operates on physical addresses and needs
physically contiguous memory. Earlier patches used contigmalloc on amd64,
but this version replaces part of a structure by a pointer to that data.
In order to not introduce an extra indirection for other architectures,
the change has been made conditional on __amd64__.
Earlier attempts to repair this problem are removed (i.e. the macros that
made amd64 use contigmalloc). The fix was submitted by Jan Mikkelsen and
modified by me to only affect amd64.
PR: 89550
Submitted by: janm at transactionware dot com (Jan Mikkelsen)
Approved by: re (Hiroki Sato)
MFC after: 2 weeks
interrupt that is shared with other devices(e.g. USB) in system and
provide a new tunable "hw.msk.legacy_intr" to activate the legacy
interrupt handler. Setting the tunable automatically disables MSI
for msk(4). Previously msk(4) used adoptive polling with taskqueue(9)
as all msk(4) hardwares I know supports MSI. However, there are cases
that MSI couldn't be used on some hardwares due to bugs in MSI
implementatins.
Tested by: Li-Lun Wang < llwang AT infor DOT org >
Approved by: re (kensmith)
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
config info. from device.hints. Some machines have ipmi controllers
that do not have attachment info in either PCI, SMBIOS or ACPI.
This idea was hacked together by me and then done properly by
jhb.
Submitted by: jhb
Reviewed by: jhb (man page)
Approved by: re (Ken Smith)
MFC after: 1 week
- Keep last transaction label for each destination.
- If the next label is not free, just give up.
- This should reduce CPU load for TX on if_fwip under heavy load.
Approved by: re (hrs)
This adds a function to agp.c to set the aperture resource ID if it's
not the usual AGP_APBASE. Previously, agp.c had been assuming
AGP_APBASE, which resulted in incorrect agp_info, and contortions by
agp_i810.c to work around it.
This also adds functions to agp.c for default AGP_GET_APERTURE() and
AGP_SET_APERTURE(), which return the aperture resource size and disallow
aperture size changes. Moving to these for our AGP drivers will likely
result in stability improvements. This should fix 855-class aperture
size detection.
Additionally, refuse to attach agp_i810 when some RAM is above 4GB and
the GART can't reference memory that high. This should be very rare.
The correct solution would be bus_dma conversion for agp, which is
beyond the scope of this change. Other AGP drivers could likely use
this change as well.
G33/Q35/Q33 AGP support is also included, but disconnected by default
due to lack of testing.
PR: kern/109724 (855 aperture issue)
Submitted by: FUJIMOTO Kou<fujimoto@j.dendai.ac.jp>
Approved by: re (hrs)
- change include style so build in kernel try OR standalone work.
- Limit HWCSUM - I was led to believe that it would work with RSS,
but our testing had odd issues which suggests this is false.
- A fatfinger error in the ioctl code made ifconfig up not work.
Approved by: re
than indirecting through ifaddr_byindex, which makes things easier with
respect to virtualized network stacks.
Submitted by: Marko Zec <zec at icir dot org>
Reviewed by: Leonid Grossman <Leonid dot Grossman at neterion dot com>
Approved by: re (kensmith)
non-sleepable lock held. drm_pci_alloc() calls them, thus drm mutex shall
not be held during the call.
Move the drm_pci_alloc() to the start of the i915_initialize() and drop the
the drm mutex around it.
Reported by: Ganbold <ganbold micom mng net>
Reviewed by: anholt
Approved by: re (hrs)
MFC after: 1 week
- use net80211 for scanning and pass the results back to the scan cache
- use ieee80211_init_channels to fill our channel list
- fix up state transitions
- depreciate the old wicontrol ioctls
- add some debugging lines (#define NDIS_DEBUG)
Reviewed by: sam
Approved by: re (kensmith)
ioctls can be removed. These have been #ifdef'd out and left as a reference in
case any of the RIDs need to be turned into sysctls at a later date.
Reviewed by: sam, avatar
Approved by: re (kensmith)
- reduce cpu usage by as much as 25% (40% -> 30) by doing txq reclaim more efficiently
- use mtx_trylock when trying to grab the lock to avoid spinning during long encap loop
- add per-txq reclaim task
- if mbufs were successfully re-claimed try another pass
- track txq overruns with sysctl
Approved by: re (blanket)
- Add controller id for Intel 82801I (ICH9).
PR: kern/114399
Submitted by: Michael Fuckner <michael@fuckner.net>
- MSI support. Disable by default due to various issues with too many
broken hardwares. MSI can be enabled through device.hints(5) or
kenv(8) by setting "hint.pcm.%d.msi=1".
Partially submitted by: kevlo
YAMAMOTO Taku <taku@tackymt.homeip.net>
Tested by: joel, kevlo, YAMAMOTO Taku
Approved by: re (hrs)
MFC after: 3 days
do the heavy lifting of the 'mii_tick' function, rue was left behind.
Implement this in a naive way. Reports from the field show this makes
the driver functional with some locking issues, as opposed to an
instant panic. Those will be addressed in a later version of the
driver.
Approved by: re@ (bmah)
Sort NETGEAR list per convention.
Swap QUALCOMM and QUALCOMM2.
Add a few vendor products.
no md5 changes with this file (except when USBVERBOSE is enabled)
Approved by: re@ (blanket)
- Handle directories and leaves other than unit directories and text leaves
correctly.
- Now we can retrieve CROM of iSight correctly.
Approved by: re (hrs)
Tested by: flz
MFC after: 3 days
in. These are exclusively in the name of the company for this round.
No new devices have been added, but the MITEL entry has been
eliminated because nothing uses it. You won't see any difference
unless you have USBVERBOSE defined for the kernel.
Approved by: re@ (blanket)
nxge: cast page size fragments down to (int). If the vm's demand paging
PAGE_SIZE is ever too big for that, we've got far bigger problems.
ofw: move va_start() a little earlier. gcc-4.2 doesn't like us modifying
the last arg before the va_start().
Approved by: re (rwatson)
would be 93C46(1Kbit) or 93C56(2Kbit). One of differences between them
is number of address lines required to access the EEPROM. For example,
93C56 EEPROM needs 8 address lines to read/write data. If 93C56
recevied premature end of required number of serial clock(CLK) to set
OP code/address of EEPROM, the result would be unexpected behavior.
Previously it tried to detect 93C46, which requires 6 address lines,
and then assumed it would be 93C56 if read data was not expected
value. However, this approach didn't work in some models/situations
as 93C56 requries 8 address lines to access its data. In order to fix
it, change EEPROM probing order such that 93C56 is detected reliably.
While I'm here change hard-coded address line numbers with defined
constant to enhance readability.
PR: 112710
Approved by: re (mux)
o Adonics Cable 205
o Aiptek PocketCAM 3Mega
o Belkin USB2SCSI
o Casio QV DigiCam
o CCYU EasyDisk ED1064
o Desknote UCR-61S2B
o Epson Stylus Photo 875DC Card Reader
o Epson Stylus Photo 895 Card Reader
o Feiya 5-in-1 Card Reader
o Hitachi Dvd-CAM DZ-MV100A Camcorder
o HP CD-WRiter+ CD-4e
o Insystem Storage Adapter v2
o Kyocera Finecam S3x
o Kyocera Finecam S4
o Kyocera Finecam S5
o Kyocera Finecam L3
o Lexar USB CF Reader
o MindAtWork Digital Wallet
o Minolta Dimage F300
o Minolta Dimage E223
o Minsumi USB Fdd
o Netac USB-CF-Card
o NetChip USB Clik! 40
o Onspec MDCFE-B USB CF Reader
o Onspec SIIG/Datafab Memory Stick + CF Reader/Writer
o Onspec Datafab-based Reader
o Onspec PNY/Datafab CF+SM Reader
o Onspec SimpleTech/Datafab CF+SM Reader
o Onspec MDSM-b Reader
o Onspec USB To CF + SM Combo (LC1)
o Onspec ImageMate SDDR55
o Panasonic LS-120 Camera
o Samsung Techwin Digimax 410
o Shuttle eUSB SmartMedia / CompactFlash Adapter
o Skanhex MD 7425 Camera
o Skanhex SX 520z Camera
o Sony Memorystick NW-MS7
o Sony Portable USB Hardrive V2
o Sony Memorystick PEG N760c
o Sony Memorystick MSC-U03
o TREK/IBM USB memory key
o Trumpion T33520 USB Flash Card Controller
o Trumpion MP3 Player
o Vivtar Vivicam 35Xx
o WinMaxGroup USB Flash Disk 64M-C
o Zoran Digital Camera EX-20 DSC
and maybe a few others...
Submitted by: Vaidas Damosevicius and flz
PR: 79893
Reviewed by: njl, flz
Approved by: re (blanket)
that should be a no-op (for example, requesting SYNC on record path).
The standards does not indicate that such requests are illegal, so
just return it as success instead of EINVAL.
Approved by: re (mux)
First, we were never correctly checking for a 24XX Status Type 0
response- that cased us to fall through to evaluate status for
commands as if this were a 2100/2200/2300 Status Type 0 response.
This is *close*, but not quite the same. This has been reported
to be apparent with some wierd lun configuration problems with
some arrays. It became glaringly apparent on sparc64 where none
of the correct byte swap things were done.
Fixing this omission then caused a whole universe shifting debug
cycle of endian issues for the 2400. The manual for 24XX f/w turns
out to be wrong about the endianness of a couple of entities. The
lun and cdb fields for the type 7 request are *not* unconditionally
big endian- they happen to be opposite of whatever the endian of
the current machine type is. Same with the sense data for the
24XX type 0 response.
While we're at it investigate and resolve some NVRAM endian
issues.
Approved by: re (ken)
MFC after: 3 days
Submitted by: Simon Schubert <corecode@fs.ei.tum.de>
- Defer flushing unsolicited response into taskqueue thread rather
than handle it directly in interrupt handler, since few of its
operations (like measuring/calibrating jack impedance) are quite
expensive.
- Misc. debugging cleanups.
Tested by: joel
Approved by: re (hrs)
MFC after: 3 days
Note: The offending quirk should have been made model/codec specific,
but since there were no records / log which model requires it, the quirk
logic had to be inverted (blacklist instead of whitelist).
Tested by: Arkadiy Dudevitch <dudevitch@englerllc.com>
Approved by: re (hrs)
MFC after: 3 days
- provide dummy routines for ic_scan_curchan and ic_scan_mindwell, we do not support those operations.
- add ieee80211_scan_done() to tell the scanning module that all channels have been scanned.
- pass IEEE80211_S_SCAN state off to net80211 so it can initiate scanning
- fix overflow in the rates array
- scale the rate value passed back from the firmware scan to the units that net80211 uses.
Submitted by: Token
Reviewed by: sam, avatar
Approved by: re (kensmith)
operating channel and use this in the scan cache rather than directly using
ic_curchan. Some firmware cards can only do a full scan and so ic_curchan does
not have the correct value.
Also add IEEE80211_CHAN2IEEE to directly dereference ic_ieee from the channel
to be used in the fast path.
Reviewed by: sam, sephe
Approved by: re (kensmith)
to be index by IEEE channel number but that is no longer the case and it needs
to be searched for.
Submitted by: avatar
Reviewed by: sam
Approved by: re (kensmith)
(1) Add size parameter to usbd_get_string()
(2) Properly limit speed when a full speed hub is plugged into a high
speed hub.
Submitted by: Hans Petter Selasky
PR: 80773, 79725
Approved by: re@ (kensmith)
yet supported by this driver. Support will be committed soon, or a
filter on all the 'newer' devices will be installed before the
release.
Approved by: re@ (blanket)
Obtained from: NetBSD, OpenBSD
Small Furry Animals by: Pink Floyd
switch (i.e. lid) is set to have an action of NONE. This is not an
invalid state, so silently return. This fixes the warning:
"acpi: request to enter state S6 failed (err 22)"
Approved by: re
the command. Make UFI devices return 'success' when asked to do a
SYNC_CACHE. There's no support for write caching in the UFI spec, so
this is the most appropriate action to undertake.
Reviewed by: scottl
Approved by: re@ (blanket)
Hellmuth with some refinements by myself and flz@. It works for me
with my non-MS mice, so nothing should be broken by it.
Submitted by: Hellmuth Michaelis
PR: 90162
Approved by: re (blanket)
pr, the submitter says:
Found this while running freebsd as guest in qemu with -usb
parameter. The patch implements the missing dynamic size based on
number of ports a hub has.
Submitted by: Lonnie Mendez
PR: 94946
Approved by: re@ (blanket)
patch that converts ms to ticks was used. Another PR states that a
return code of 0 is the right one for libusb.
Submitted by: Lonnie Mendez
PR: 94311
Approved by: re (blanket)
adequate. Increase them to 1k. The referenced PR made this a sysctl,
but that seems like overkill to me. The difference between 320 and
2048 bytes in modern systems, even embedded ones, seems to be in the
noise to be worth the extra hair to make it settable.
PR: 74609
Submitted by: Divacky Roman
Approved by: re (blanket)
applied to, but I'd think both), honor the timeout that's been set.
Return 0 bytes to be consistant with what libusb expects. By default,
the timeout will be zero, so only applications that change the default
will see a change. The patch only seems to apply to the interrupt end
points, but it should also apply to isochronous endpoints as well.
Submitted by: Maurice Castro
PR: 110122
Approved by: re (blanket)
some false positives but at this moment it is better to add
support then to dont have it at all (comment from Soren).
PR: kern/111516
Submitted by: Thomas Nystrom <thn at saeab dot se>
Approved by: re (kensmith)
Approved by: imp (mentor)
OK'ed by: sos (With the comment noted above about false
positives).
put out a ispreqt2e_t structure onto the request queue- not a ispreqt2_t
structure. I forgot that the 23XX can use a t2 structure.
Approved by: re (ken, implicitly)
MFC after: 3 days
changes for example:
(From Craig Leres):
tip to a rocketport line
run "/etc/rc.d/devfs restart"
exit tip
(wait for the system to reboot)
Thanks to Robert Watson for poking me to fix this.
PR: kern/109152
Approved by: imp (mentor)
Approved by: re (kensmith)
Reviewed by: jhb
Submitted by: Craig Leres <leres@ee dot lbl dot gov>
of the file numerically for vendors and then each product numerically
by vendor (with all the foo2's sorting after the foo's). Someday, all
the usbdevs will be merged, I hope, but until then, we have these
mega-merges.
This also finishes the LINKSYS4 -> CISCOLINKSYS rename.
Approved by: re@ (blanket)
firmware reset. Also zero out struct iwi_rateset although its not strictly
necessary.
Reported by: Maxim Konovalov
Reviewed by: sam
Approved by: re (bmah)
to put out a ispreqt3e_t structure onto the request queue-
not a ispreqt3_t structure. We weren't. This turns out only
to really matter for big endian machines.
Approved by: re (ken)
MFC after: 3 days
around an output freezing problem (see the CVS log for details). This
is the same approach that sio takes to solve that problem. However,
ucom has a problem that sio doesn't have.
Consider the case where output is pending, and the device is closed.
ttyclose calls tt_close (which indirects to ucomclose) and then calls
ttyflush which calls tt_stop (which indirects to ucomstop). Since
ucomclose removed all the usb transfer points, sc_oxfer will be NULL
when ucomstop calls ucomstart. This results in a null pointer
dereference.
Since calling ucomstart in ucomstart solves other problems, we need to
work with this calling sequence. The easiest way to do that is to
bail early if sc_oxfer is NULL.
Kazuaki ODA-san came up with this patch, and filed a PR. I had seen
this bug at work and this patch does seem to solve it. He had no idea
why it worked, but knew that either this patch, or backing out ucom.c
1.56 fixed his panic. I just did the legwork of chasing down the code
paths that would cause this, and added a comment. This is obscure
enough to warrant a comment, I think.
Submitted by: Kazuaki ODA-san
PR: 113964
Approved by: re (bmah)
where a device timeout that occurs with a mgt frame on the tx q
will leave the net80211 layer w/o any way to make progress.
Reviewed by: thompsa, sephe
Approved by: re (hrs)
request queues rather than shove it down a word at a time, we have
to remember to put it into little endian format. Use the macros
ISP_IOXPUT_{16,32} for this purpose. Otherwise, on sparc the firmware
is loaded garbled and we get a (not surprisingly) firmware checksum
failure and the card won't start and we don't attach it.
Approved by: re (bruce)
MFC after: 3 days
Improvements:
* /etc/rc.suspend,rc.resume are always run, no matter the source of the
suspend request (user or kernel, apm or acpi)
* suspend now requires positive user acknowledgement. If a user program
wants to cancel the suspend, they can. If one of the user programs
hangs or doesn't respond within 10 seconds, the system suspends anyway.
* /dev/apm is clonable, allowing multiple listeners for suspend events.
In the future, xorg-server can use this to be informed about suspend
even if there are other listeners (i.e. apmd).
Changes:
* Two new ACPI ioctls: REQSLPSTATE and ACKSLPSTATE. Request begins the
process of suspending by notifying all listeners. acpi is monitored by
devd(8) and /dev/apm listener(s) are also counted. Users register their
approval or disapproval via Ack. If anyone disapproves, suspend is vetoed.
* Old user programs or kernel modules that used SETSLPSTATE continue to
work. A message is printed once that this interface is deprecated.
* acpiconf gains the -k flag to ack the suspend request. This flag is
undocumented on purpose since it's only used by /etc/rc.suspend. It is
not intended to be a permanent change and will be removed once a better
power API is implemented.
* S5 (power off) is no longer supported via acpiconf -s 5 or apm -z/-Z.
This restores previous behavior of halt/shutdown -p being the interface.
* Miscellaneous improvements to error reporting
Approved by: re
o Consistently use device_foo_t and bus_foo_t for functions implementing
device_foo and bus_foo respectively. Adjust those routines that were wrong
(we should do this throughout the tree).
o make all the modules depend on usb. Otherwise these modules won't
load.
o ucycom doesn't need usb_port.h
o Minor unifdefing
o uhub, umass, ums, urio, uscanner conversion complete.
o ukbd: Remove the NO_SET_PROTO quirk (fixes a PR 77940). NetBSD removed
their check and setting the proto a long time ago.
o umodem panic fixed. UQ_ASSUME_CM_OVER_DATA quirk removed because I've never
seen a umodem that needed this rejection for proection (this gets rid of
~20% of the quirks).
Approved by: re@ (kensmith)
PR: 77940
Older drivers that do not wish to convert to the native API (which
will work with both 6.x and 7.x) can simply include
<dev/usb/usb_port.h>. Drivers in the tree shouldn't these macros,
unless they actually work on other OSes and are actively maintained.
Approved by: re@
