Summary:
This switch is based off of the AR8327/AR8337 external switch/PHY.
However unlike the AR8327/AR8337 it itself doesn't have any PHYs;
instead an external PHY connects to it using the PSGMII port.
Differential Revision: https://reviews.freebsd.org/D34112
Reviewed by: manu
This code is inspired by the ar40xx code in openwrt, which itself
is based on the Qualcomm QCA-SSDK. Both of these sources are, amusingly,
BSD licenced - and thus I have included some of the comments in the
hardware workaround paths to document some of the magic numbers.
This adds support for the IPQ4018/IPQ4019 MDIO bus. This is used to
talk to external PHYs and switches. (There's an internal switch
in the IPQ4018/IPQ4019 as well, but it's accessible via MMIO/AXI.)
Differential Revision: https://reviews.freebsd.org/D34110
Reviewed by: manu
This adds some very simple DWC3 glue for the IPQ4018/IPQ4019.
Other chipsets introduce reset line iteration, some further
clock line iteration and some customisations; I'll look at adding
those later.
This is enough to finally bring up USB 3.0 on my IPQ4018 ASUS
RT-58U router.
This adds the USB 2.0 and 3.0 PHY support for the IPQ4018/IPQ4019.
All it really needs to do is gate the relevant clocks on/off in the
right order with the right delays.
The Qualcomm TCSR is some top level glue between multiple IP blocks,
both for doing configuration of said IP blocks, some IPC between
them (mostly between multiple execution environments - eg trustzone
and non-TZ), and interrupt status bits for them.
However, for the IPQ4018/IPQ4019, it only is used as a small subset
of IP block configuration. As for what it actually gets used as
for other Qualcomm chipsets? Well, that'll have to wait.
It's a bit of a mess in linux and openwrt. See, every different
SoC support branch ends up with some different TCSR code for it.
So instead, I'm going to land a single TCSR driver that I'm going
to use for the IPQ4018/IPQ4019. When I add the next chipset, I'll
figure out how to organise things so there's a single TCSR driver
that works for multiple platforms.
The Qualcomm Universal Peripherals Engine (QUP) is a unified SPI and I2C
peripheral that ships with a variety of Qualcomm SoCs.
It supports three transfer modes - single PIO, block PIO and DMA.
This driver only supports the single PIO mode, which is enough to
bootstrap the rest of the SPI NAND/NOR support and means I can do
things like read the Wifi calibration data from NOR. It has some
hardware support code for the other transfer modes as well as
some support for split transfers (ie, transfers with no read or
write phase), but I haven't yet implemented those.
This driver is based on four sources - the linux driver, the u-boot
driver, some initial work done for APQ8064 by mmel@, and the APQ8064
Technical Reference Manual which is surprisingly free and open to
read. The linux and u-boot drivers approach a variety of things
completely differently, from how PIO is done, the hardware support
for re-ordering bytes in a transfer word and how the CS lines
are used.
Tested:
* IPQ4018, SPI to NAND/NOR flash, PIO only
Now that the clock drivers are in the tree, the cpufreq driver will
"just work".
Tested:
* IPQ4018, testing performance of dd from /dev/zero->/dev/null at
each frequency step.
Define CC_NEWRENO in all the appropriate DEFAULTS and std.* config
files. It's the default congestion control algorithm. Add code to cc.c
so that CC_DEFAULT is "newreno" if it's not overriden in the config
file.
Sponsored by: Netflix
Fixes: b8d60729de ("tcp: Congestion control cleanup.")
Revired by: manu, hselasky, jhb, glebius, tuexen
Differential Revision: https://reviews.freebsd.org/D32964
NOTE: HEADS UP read the note below if your kernel config is not including GENERIC!!
This patch does a bit of cleanup on TCP congestion control modules. There were some rather
interesting surprises that one could get i.e. where you use a socket option to change
from one CC (say cc_cubic) to another CC (say cc_vegas) and you could in theory get
a memory failure and end up on cc_newreno. This is not what one would expect. The
new code fixes this by requiring a cc_data_sz() function so we can malloc with M_WAITOK
and pass in to the init function preallocated memory. The CC init is expected in this
case *not* to fail but if it does and a module does break the
"no fail with memory given" contract we do fall back to the CC that was in place at the time.
This also fixes up a set of common newreno utilities that can be shared amongst other
CC modules instead of the other CC modules reaching into newreno and executing
what they think is a "common and understood" function. Lets put these functions in
cc.c and that way we have a common place that is easily findable by future developers or
bug fixers. This also allows newreno to evolve and grow support for its features i.e. ABE
and HYSTART++ without having to dance through hoops for other CC modules, instead
both newreno and the other modules just call into the common functions if they desire
that behavior or roll there own if that makes more sense.
Note: This commit changes the kernel configuration!! If you are not using GENERIC in
some form you must add a CC module option (one of CC_NEWRENO, CC_VEGAS, CC_CUBIC,
CC_CDG, CC_CHD, CC_DCTCP, CC_HTCP, CC_HD). You can have more than one defined
as well if you desire. Note that if you create a kernel configuration that does not
define a congestion control module and includes INET or INET6 the kernel compile will
break. Also you need to define a default, generic adds 'options CC_DEFAULT=\"newreno\"
but you can specify any string that represents the name of the CC module (same names
that show up in the CC module list under net.inet.tcp.cc). If you fail to add the
options CC_DEFAULT in your kernel configuration the kernel build will also break.
Reviewed by: Michael Tuexen
Sponsored by: Netflix Inc.
RELNOTES:YES
Differential Revision: https://reviews.freebsd.org/D32693
* add the extres stuff into the build, I'm going to end up leveraging
all of it
* include the qcom-gcc-ipq4018 driver which currently implements the hwreset
side of the API.
Reviewed by: andrew, manu, imp
Differential Revision: https://reviews.freebsd.org/D32723
This is a very simple implementation of Qualcomm's SCM API.
It is just the structure/field definitions and the atomic SCM
call which doesn't use the structs yet - it uses the field
definitions inside registers.
I've tested that setting the cold boot address via the atomic
API is fine - Linux does the same thing. But not all SCM calls
can be done via the legacy API.
This is a reimplementation based on the Linux qualcomm SCM legacy
code and definitions.
Tested:
* Qualcomm IPQ4018 AP, as part of other changes for doing SMP bring-up
Reviewed by: andrew, manu, imp
Differential Revision: https://reviews.freebsd.org/D32723
Summary:
This is enough to allow this ASUS router to reboot successfully.
I tried the watchdog path and although it fires, it isn't rebooting!
It's just hanging, likely somewhere in TZ.
This is the MVP required to initialise and consume random data from
the QCA PRNG hardware found on the IPQ401x.
Test Plan: * ASUS RT-AC58U router, IPQ4019
Subscribers: imp, andrew
Differential Revision: https://reviews.freebsd.org/D32723
Summary:
This adds required IPQ4018/IPQ4019 SoC support to boot.
It also includes support for disabling the ARMv7 hardware
breakpoint / debug stuff at compile time as this is
required for the IPQ SoCs, and printing out the undefined
instruction itself.
Test Plan: * compiled/booted on an IPQ4019 SoC AP
Reviewers: #core_team!
Subscribers: imp, andrew
Differential Revision: https://reviews.freebsd.org/D32538
Remove the option from NOTES/LINT, and add to NOTES for powerpc and
riscv.
PR: 259036
Requested by: John Hay <john@sanren.ac.za>
Discussed with: ian, imp
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
The firmware was already in the tree when I did this commit, and I
missed the message. The bug was obsolete.
This reverts commit 9e3761d126.
PR: 237466
Sponsored by: Netflix
The fslsdma device requires sdma_fw, but that's not included in
GENERIC. That firmware is not in the FreeBSD tree at the moment, but
could easily be.
The license for the firmware can be found in the linux firmware repo:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=3123d78e09d2f815de4d94aa35c07b3c0469c80e
and looks to be a BSD license + no reverse engineer.
We can add this back after the firmware is imported, made a port, or
whose automatic loading can be made to happen.
Reviewed by: imp (with ian finding the license)
PR: 237466
MFC after: 1 week
While here, fix all links to older en_US.ISO8859-1 documentation
in the src/ tree.
PR: 255026
Reported by: Michael Büker <freebsd@michael-bueker.de>
Reviewed by: dbaio
Approved by: blackend (mentor), re (gjb)
MFC after: 10 days
Differential Revision: https://reviews.freebsd.org/D30265
It was used for testing armv6 under QEMU, however since then we added
support for the QEMU virt platform.
Reviewed by: imp, manu
Differential Revision: https://reviews.freebsd.org/D29707
There are now options for specifying the debug port via tunable
(hw.fdt.dbgport) and device tree (/chosen/freebsd-dbgpath), so this can
be usefully included in GENERIC.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D29152
This is the superset of the nooptions found in the -DEBUG kernels.
Reviewed by: emaste, manu
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D28152
Add 64-bit address support to Cadence CGEM Ethernet driver for use in
other SoCs such as the Zynq UltraScale+ and SiFive HighFive Unleashed.
Reviewed by: philip, 0mp (manpages)
Differential Revision: https://reviews.freebsd.org/D24304
It will be used by the upcoming HID-over-i2C implementation. Should be
no-op, except hid.ko module dependency is to be added to affected drivers.
Reviewed by: hselasky, manu
Differential revision: https://reviews.freebsd.org/D27867
Some imx6 drivers are being converted to use features that weren't available
when they were first written (such as accessing shared device registers via
the syscon pseudo-device), so imx6 custom kernels that reference those
devices will now need this infrastructure in place.
Now that config(8) has supported include for 19 years, transition to
including the NOTES files. include support didn't exist at the time,
nor did the envvar stuff recently added. Now that it does, eliminate
the building of LINT files by just including everything you need.
Note: This may cause conflicts with updating in some cases.
find sys -name LINT\* -rm
is suggested across this commit to remove the generated LINT
files.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D26540
This removes SCTP from in-tree kernel configuration files. Now, SCTP
can be enabled by simply loading the module, as discussed on
freebsd-net@.
Reviewed by: tuexen
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D25611
Now that armv5 is gone, we no longer need multiple LINT files. Kill
the odd-ball support here. From now on, we just have LINT built from
notes like all the other platforms. Keep the removal of LINT-V5/7
to remove stale files for a while still..
This is a qspi driver for the Xilinx Zynq-7000 chip.
It could be useful for anyone wanting to boot a system from flash memory
instead of SD cards.
Submitted by: Thomas Skibo (thomasskibo@yahoo.com)
Differential Revision: https://reviews.freebsd.org/D14698
We use armv7/GENERIC for the RPI2 images. The original RPI2 is actually a
32-bit BCM2836, but v1.2 was upgraded to the 64-bit BCM2837. The project
continues to provide the RPI2 image as armv7, as it's the lowest common
denominator of the two. Historically, we've just kind of implicitly
acknowledged this by including some bcm2837 bits on a SOC_BCM2836 kernel
config -- this worked until r354875 added code that actually cared.
Acknowledge formally that BCM2837 is valid in arm32.
This name is inconsistent with the other BCM* SOC on !arm64 for two reasons:
1. It's a pre-existing option on arm64, and
2. the naming convention on arm/ should've arguably changed to include BRCM
#1 seems to be a convincing enough argument to maintain the existing name
for it.
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
r354290 removed arm.arm from universe, but arm.arm kernels were still
found and built during the kernel stage. I'm not aware of a better way
to address this at the moment, but since there aren't many arm.arm
kernels anyhow just add an explicit NO_UNIVERSE to them.
Reported by: rpokala
