With write-allocate cache we get into the following scenario:
1. data has been updated in the memory by the USB HC, but
2. D-cache holds an un-flushed value of it
3. when affected cache line is being replaced, the old (un-flushed) value is
flushed and overwrites the newly arrived
This is possible due to how write-allocate works with virtual caches (ARM for
example).
In case of USB transfers it leads to fatal tags discrepancies in umass(4)
operation, which look like the following:
umass0: Invalid CSW: tag 1 should be 2
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 3
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 4
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 5
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 6
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): error 5
(probe0:umass-sim0:0:0:0): Retries Exausted
To eliminate this, a BUS_DMASYNC_PREREAD sync operation is required in
usbd_start_transfer().
Credits for nailing this down go to Grzegorz Bernacki gjb AT semihalf DOT com.
Reviewed by: imp
Approved by: cognet (mentor)
- Include lock.h in lockmgr.h as nested header in order to safely use
LOCK_FILE and LOCK_LINE. As long as this code will be replaced soon
we can tollerate for a while this namespace pollution even if the real
fix would be to let lockmgr() depend by lock.h as a separate header.
NOP-message polling in ciss_periodic().
Note that setting the tunable to non-zero can be workaround only for
`ADAPTER HEARTBEAT FAILED' problem, and may freeze the system w/o
the problem.
Reviewed by: scottl
Reported by: Attila Nagy
MFC after: 3 days
- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
o conversion to callout(9) API.
o add a missing driver lock in bfe_ifmedia_sts().
o use our callout to drive watchdog timer.
o restart Tx routine if pending queued packets are present in
watchdog handler.
o unarm watchdog timer only if there are no queued packets.
o don't blindly reset phy and let phy driver handle link change
request in bfe_init_locked().
o return the status of mii_mediachg() to caller in
bfe_ifmedia_upd(). Previously it always returned 0 to caller.
o add check for IFF_DRV_RUNNING flag as well as IFF_DRV_OACTIVE
in bfe_start_locked().
o implement miibus_statchg method that keeps track of current
link state changes as well as negotiated speed/duplex/
flow-control configuration.
Reprogram MAC to appropriate duplex state. Flow-control
configuration was also implemented but commented out at the
moment. The flow-control configuration will be enabled again
after we have general flow-control framework in mii layer.
Reported by: Yousif Hassan < yousif () alumni ! jmu ! edu >
Tesdted by: Yousif Hassan < yousif () alumni ! jmu ! edu >
- Fix whitespace according to style(9).
- Sync the comment describing why we have to wait in nsphy_reset()
with nsphyter_reset(). It's true that the manual tells to not do a
reset within 500us of applying power but that's unlikely the cause
of problems seen here. Generally having to wait 500us after a reset
however is.
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
- Remove the "thread" argument from the lockmgr() function as it is
always curthread now
- Axe lockcount() function as it is no longer used
- Axe LOCKMGR_ASSERT() as it is bogus really and no currently used.
Hopefully this will be soonly replaced by something suitable for it.
- Remove the prototype for dumplockinfo() as the function is no longer
present
Addictionally:
- Introduce a KASSERT() in lockstatus() in order to let it accept only
curthread or NULL as they should only be passed
- Do a little bit of style(9) cleanup on lockmgr.h
KPI results heavilly broken by this change, so manpages and
FreeBSD_version will be modified accordingly by further commits.
Tested by: matteo
- Improve error handling for load operations.
- Fix a memory corruption bug when using certain linux management apps.
- Allocate all commands up front to avoid OOM deadlocks later on.
checksum offoload by downloading AIC-6915 firmware. Changes are
o Header file cleanup.
o Simplified probe logic.
o s/u_int{8,16,32}_t/uint{8,16,32}_t/g
o K&R -> ANSI C.
o In register access function, added support both memory mapped and
IO space register acccess. The function will dynamically detect
which method would be choosed.
o sf_setperf() was modified to support strict-alignment
architectures.
o Use SF_MII_DATAPORT instead of hardcoded value 0xffff.
o Added link state/speed, duplex changes handling task q. The task q
is also responsible for flow control settings.
o Always hornor link up/down state reported by mii layers. The link
state information is used in sf_start() to determine whether we
got a valid link.
o Added experimental flow-control setup. It was commented out but
will be activated once we have flow-cotrol infrastructure in mii
layer.
o Simplify IFF_UP/IFCAP_POLLING and IFF_PROMISC handling logic. Rx
filter always honors promiscuous mode.
o Implemented suspend/resume methods.
o Reorganized Rx filter routine so promiscuous mode changes doesn't
require interface re-initialization.
o Reimplemnted driver probe routine such that it looks for matching
device from supported hardware list table. This change will help to
add newer hardware revision to the driver.
o Use ETHER_ADDR_LEN instead of hardcoded value.
o Prefer memory space register mapping over I/O space as the hardware
requires lots of register access to get various consumer/producer
index. Failing to get memory space mapping, sf(4) falls back to I/O
space mapping. Use of memory space register mapping requires
somewhat large memory space(512K), though.
o Switch to simpler bus_{read,write}_{1,2,4}.
o Use PCIR_BAR macro to get BARs.
o Program PCI cache line size if the cache line size was set to 0
and enable PCI MWI.
o Add a new sysctl node 'dev.sf.N.stats' that shows various MAC
counters for Rx/Tx statistics.
o Add a sysctl node to configure interrupt moderation timer. The
timer defers interrupts generation until time specified in timer
control register is expired. The value in the timer register is in
units of 102.4us. The allowable range for the timer is 0 - 31
(0 ~ 3.276ms).
The default value is 1(102.4us). Users can change the timer value
with dev.sf.N.int_mod sysctl(8) variable/loader(8) tunable.
o bus_dma(9) conversion
- Enable 64bit DMA addressing.
- Enable 64bit descriptor format support.
- Apply descriptor ring alignment requirements(256 bytes alignment).
- Apply Rx buffer address alignment requirements(4 bytes alignment).
- Apply 4GB boundary restrictions(Tx/Rx ring and its completion ring
should live in the same 4GB address space.)
- Set number of allowable number of DMA segments to 16. In fact,
AIC-6915 doesn't have a limit for number of DMA segments but it
would be waste of Tx descriptor resource if we allow more than 16.
- Rx/Tx side bus_dmamap_load_mbuf_sg(9) support.
- Added alignment fixup code for strict-alignment architectures.
- Added endianness support code in Tx/Rx descriptor access.
With these changes sf(4) should work on all platforms.
o Don't set if_mtu in device attach, it's handled in ether_ifattach.
o Use our own callout to drive watchdog timer.
o Enable VLAN oversized frames and announce sf(4)'s VLAN capability
to upper layer.
o In sf_detach(), remove mtx_initialized KASSERT as it's not possible
to get there without initialzing the mutex. Also mark that we're
about to detaching so active bpf listeners do not panic the system.
o To reduce PCI register access cycles, Rx completion ring is
directly scanned instead of reading consumer/producer index
registers. In theory, Tx completion ring also can be directly
scanned. However the completion ring is composed of two types
completion(1 for Tx done and 1 and DMA done). So reading producer
index via register access would be more safer way to detect the
ring wrap-around.
o In sf_rxeof(), don't use m_devget(9) to align recevied frames. The
alignment is required only for strict-alignment architectures and
now the alignment is handled by sf_fixup_rx() if required. The
removal of the copy operation in fast path should increase Rx
performance a lot on non-strict-alignemnt architectures such as
i386 and amd64.
o In sf_newbuf(), don't set descriptor valid bit as sf(4) is
programmed to run with normal mode. In normal mode, the valid bit
have no meaning. The valid bit should be used only when the
hardware uses polling(prefetch) mode. The end of descriptor queue
bit could be used if needed, but sf(4) relys on auto-wrapping of
hardware on 256 descriptor queue entries so both valid and
descriptor end bit are not used anymore.
o Don't disable generation of Tx DMA completion as said in datasheet
and use the Tx DMA completion entry instead of relying on Tx done
completion entry. Also added additional Tx completion entry type
check in Tx completion handler.
o Don't blindly reset watchdog timer in sf_txeof(). sf(4) now unarm
the the watchdog only if there are no active Tx descriptors in Tx
queue.
o Don't manually update various counters in driver, instead, use
built-in MAC statistic registers to update them. The statistic
registers are updated in every second.
o Modified Tx underrun handlers to increase the threshold value
in units of 256 bytes. Previously it used to increase 16 bytes
at a time which seems to take too long to stabalize whenever Tx
underrun occurrs.
o In interrupt handler, additional check for the interrupt is
performed such that interrupts only for this device is allowed to
process descriptor rings. Because reading SF_ISR register clears
all interrtups, nuke writing to a SF_ISR register.
o Tx underrun is abonormal condition and SF_ISR_ABNORMALINTR includes
the interrupt. So there is no need to inspect the Tx underrun again
in main interrupt loop.
o Don't blindly reinitialize hardware for abnormal interrupt
condition. sf(4) reintializes the hardware only when it encounters
DMA error which requires an explicit hardware reinitialization.
o Fix a long standing bug that incorrectly clears MAC statistic
registers in sf_init_locked.
o Added strict-alignment safe way of ethernet address reprogramming
as IF_LLADDR may return unaligned address.
o Move sf_reset() to sf_init_locked in order to always reset the
hardware to a known state prior to configuring hardware.
o Set default Rx DMA, Tx DMA paramters as shown in datasheet.
o Enable PCI busmaster logic and autopadding for VLAN frames.
o Rework sf_encap.
- Previously sf(4) used to type 0 of Tx descriptor with padding
enabled to store driver private data. Emebedding private data
structures into descriptors is bad idea as the structure size
would be different between 64bit and 32bit architectures. The
type 0 descriptor allows fixed number of DMA segments in
a descriptor format and provides relatively simple interface to
manage multi-fragmented frames.
However, it wastes lots of Tx descriptors as not all frames are
fragmented as the number of allowable segments in a descriptor.
- To overcome the limitation of type 0 descriptor, switch to type
2 descriptor which allows 64bit DMA addressing and can handle
unliumited number of fragmented DMA segments. The drawback of
type 2 descriptor is in its complexity in managing descriptors
as driver should handle the end of Tx ring manually.
- Manually set Tx desciptor queue end mark and record number of
used descriptors to reclaim used descriptors in sf_txeof().
o Rework sf_start.
- Honor link up/down state before attempting transmission.
- Because sf(4) uses only one of two Tx queues, use low priority
queue instead of high one. This will remove one shift operation
in each Tx kick command.
- Cache last produder index into softc such that subsequenet Tx
operation doesn't need to access producer index register.
o Rewrote sf_stats_update to include all available MAC statistic
counters.
o Employ AIC-6915 firmware from Adaptec and implement firmware
download routine and TCP/UDP checksum offload.
Partial checksum offload support was commented out due to the
possibility of firmware bug in RxGFP.
The firmware can strip VLAN tag in Rx path but the lack of firmware
assistance of VLAN tag insertion in transmit side made it useless
on FreeBSD. Unlike checksum offload, FreeBSD requires both Tx/Rx
hardware VLAN assistance capability. The firmware may also detect
wakeup frame and can wake system up from states other than D0.
However, the lack of wakeup support form D3cold state keep me from
adding WOL capability. Also detecting WOL frame requires firmware
support but it's not yet known to me whether the firmware can
process the WOL frame.
o Changed *_ADDR_HIADDR to *_ADDR_HI to match other definitions of
registers.
o Added definitioan to interrupt moderation related constants.
o Redefined SF_INTRS to include Tx DMA done and DMA errors. Removed
Tx done as it's not needed anymore.
o Added definition for Rx/Tx DMA high priority threshold.
o Nuked unused marco SF_IDX_LO, SF_IDX_HI.
o Added complete MAC statistic register definition.
o Modified sf_stats structure to hold all MAC statistic regiters.
o Nuke various driver private padding data in Tx/Rx descriptor
definition. sf(4) no longer requires private padding. Also remove
unused padding related definitions. This greatly simplifies
descriptor manipulation on 64bit architectures.
o Becase we no longer pad driver private data into descriptor,
remove deprecated/not-applicable comments for padding.
o Redefine Rx/Tx desciptor status. sf(4) doesn't use bit fileds
anymore to support endianness.
Tested by: bruffer (initial version)
be wrong but I couldn't find a way to make it work. In addition, the
number of TxGFP instruction does not match the firmware image size,
so I guess something was wrong when Adaptec generated the TxGFP
firmware from their DDK.
According to datasheet, normally, the first GFP instruction would be
opcode C, WaitForStartOfFrame, to synchronize checksumming with
incoming frame. But the first instruction in TxGFP firmware was
opcode 1, BrToImmIfTrue, so it could not process checksum correctly,
I guess. Checking for RxGFP firmware also indicates the first
instruction should be opcode C. Since the number of instructions in
TxGFP firmware lacks exactly one instruction, I prepended the opcode
C to TxGFP firmware image. With this change, the resulting image size
perfectly matches with the nummber of instructions and Tx checksum
offload seems to work without problems.
since the the command and data that is being built to be sent to or read
from the HW lives in the softc. Commands are later run via an_setdef etc.
In the ioctl path various references are kept to the data stored in
the softc so it needs to be protected. Almost think of the command
in the softc a global variable since it essentially is. Since locking
wasn't done in this type of context the commands would get corrupted.
Thanks to avatar@ for catching some lock issues and dhw@ for testing.
Things are a lot more stable except for the MPI-350 cards. My an(4)
remote laptop stays on the network now.
The driver should be changed so that it uses private memory that is passed
to the functions that talk to the card. Then only those functions would
really need to grab locks.
Reviewed by: avatar@
shortest possible chain of mbufs of m_defrag(9). What we want is
chains of mbufs that can be safely stored to a Tx descriptor which
can have up to STGE_MAXTXSEGS mbufs. The ethernet controller does
not need to align Tx buffers on 32bit boundary. So the use of
m_defrag(9) was waste of time.
problems when the DRM driver is loaded and the AIXGL extension is loaded
, the AIXGL driver requests a drm_close and this will cause the radeon
driver to fail while starting X windows.
PR: kern/114688
Submitted by: vehemens <vehemens at verizon dot net>
Prodded by: Robert Noland
Approved by: imp (mentor, a while ago already), anholt
MFC After: 1 week
- Track packet zone mbufs separately from other mbufs
- free packet zone buffers via m_free rather than trying to manage the refcount
as with clusters - its refcount and management seems to be "special"
but reread it from the device_t every time the device list is fetched.
Previously the device name in pciconf -l would not be updated when a driver
was unloaded or if a device was detached and attached to a different
driver.
MFC after: 1 week
PR: kern/104777
Submitted by: "Iasen Kostoff" tbyte | otel net
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
spec:
- Use read/modify/write cycles to enable and disable the HPET instead of
writing 0 to reserved bits.
- Shutdown the HPET during suspend as encouraged by the spec.
- Fail to attach to an HPET with a period of zero.
MFC after: 1 week
PR: kern/119675 [3]
Reported by: Leo Bicknell | bicknell ufp.org
- Fix a bug introduced in 1.4.20 where speculative read by the processor in the
write-only doorbell region would cause a target-abort (as opposed to simply
returning random data). This could manifest itself as NMI or machine freeze
depending on how the BIOS/OS/chipset configuration handles target-abort.
- Add support for new revisions of -R cards (with AEL1002/AEL1010 xaui->xfi)
- Increase an internal timing (dispatch engine): fix possible spurious reset
(seen on very few cards).
- increase asserts for mbuf accounting
- track outstanding mbufs (maps very closely to leaked)
- actually only create one thread per port if !multiq
Oddly enough this fixes the use after free
- move txq_segs to stack in t3_encap
- add checks that pidx doesn't move pass cidx
- simplify mbuf free logic in collapse mbufs routine
- move cxgb_tx_common in to cxgb_multiq.c and rename to cxgb_tx
- move cxgb_tx_common dependencies
- further simplify cxgb_dequeue_packet for the non-multiqueue case
- only launch one service thread per port in the non-multiq case
- remove dead cleaning code from cxgb_sge.c
- simplify PIO case substantially in by returning directly from mbuf collapse
and just using m_copydata
- remove gratuitous m_gethdr in the rx path
- clarify freeing of mbufs in collapse
o Increased number of Rx/Tx descriptors to 256 for 8169 GigEs
because it's hard to push the hardware to the limit with default
64 descriptors.
TSO requires large number of Tx descriptors to pass a full sized
TCP segment(65535 bytes IP packet) to hardware. Previously it
consumed 32 Tx descriptors, assuming MCLBYTES DMA segment size,
to send the TCP segment which means re(4) couldn't queue more
than two full sized IP packets.
For 8139C+ it still uses 64 Rx/Tx descriptors due to its hardware
limitations. With this changes there are (very) small waste of
memory for 8139C+ users but I don't think it would affect 8139C+
users for most cases.
o Various bus_dma(9) fixes.
- The hardware supports DAC so allow 64bit DMA operations.
- Removed BUS_DMA_ALLOC_NOW flag.
- Increased DMA segment size to 4096 from MCLBYTES because TSO
consumes too many descriptors with MCLBYTES DMA segment size.
- Tx/Rx side bus_dmamap_load_mbuf_sg(9) support. With these
changes the code is more readable than previous one and got a
(slightly) better performance as it doesn't need to pass/
decode arguments to/from callback function.
- Removed unnecessary callback function re_dmamap_desc() and
nuked rl_dmaload_arg structure which was used in the callback.
- Additional protection for DMA map load failure. In case of
failure reuse current map instead of returning a bogus DMA
map.
- Deferred DMA map unloading/sync operation for maximum
performance until we really need to load new DMA map. If we
happen to reuse current map(e.g. input error) there is no need
to sync/unload/load again.
- The number of allowable Tx DMA segments for a mbuf chains are
now 32 instead of magic nseg value. If the number of available
Tx descriptors are short enough to send highly fragmented mbuf
chains an optimized re_defrag() is called to collapse mbuf
chains which is supposed to be much faster than m_defrag(9).
re_defrag() was borrowed from ath(4).
- Separated Rx/Tx DMA tag from a common DMA tag such that Rx DMA
tag correctly uses DMA maps that were created with DMA alignment
restriction(8bytes alignments). Tx DMA tag does not have such
alignment limitation.
- Added additional sanity checks for DMA ring map load failure.
- Added additional spare Rx DMA map for graceful handling of Rx
DMA map load failure.
- Fixed misused bus_dmamap_sync(9) and added missing
bus_dmamap_sync(9) in re_encap()/re_txeof()/re_rxeof().
o Enabled TSO again as re(4) have reasonable number of Tx
descriptors.
o Don't touch DMA address of a Tx descriptor in re_txeof(). It's
not needed.
o Fix incorrect update of if_ierrors counter. For Rx buffer
shortage it should update if_qdrops as the buffer is reused.
o Added checks for unsupported H/W revisions and return ENXIO for
these hardwares. This is required to remove resource allocation
code in re_probe as other drivers do in device probe routine.
o Modified descriptor index manipulation macros as it's now possible
to have different number of descriptors for Rx/Tx.
o In re_start, to save a lock operation, use IFQ_DRV_IS_EMPTY before
trying to invoke IFQ_DRV_DEQUEUE. Also don't blindly call re_encap
since we already know the number of available Tx descriptors in
advance.
o Removed RL_TX_DESC_THLD which was used to reserve RL_TX_DESC_THLD
descriptors in Tx path. There is no such a limitation mentioned in
8139C+/8169/8110/8168/8101/8111 datasheet and it seems to work ok
without reserving RL_TX_DESC_THLD descriptors.
o Fix a comment for RL_GTXSTART. The register is 8bits register.
o Added comments for 8169/8139C+ hardware restrictions on descriptors.
o Removed forward declaration for "struct rl_softc", it's not needed.
o Added a new structure rl_txdesc for Tx descriptor managements and
a structure rl_rxdesc for Rx descriptor managements.
o Removed unused member variable rl_intlock in driver softc. There are
still several unused member variables which are supposed to be used
to access hardware statistics counters. But it seems that accessing
hardware counters were not implemented yet.
- Turn on WOL bits in suspend/shutdown method.
- WOL is disabled in resume routine as WOL can interfere normal
Rx operation.
- Move stge_reset() to stge_init_locked() as resetting hardware
clears configured Rx information which in turn results in
non-working Rx module after suspend/shutdown operation.
conjuction with 'thread' argument passing which is always curthread.
Remove the unuseful extra-argument and pass explicitly curthread to lower
layer functions, when necessary.
KPI results broken by this change, which should affect several ports, so
version bumping and manpage update will be further committed.
Tested by: kris, pho, Diego Sardina <siarodx at gmail dot com>
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
a panic race on module unload. The wakeup() is internal to
kproc_exit/kthread_exit. The correct fix is to fix the msleep() in
detach to sleep on fdc->fdc_thread instead of &fdc->fdc_thread.
Noted and reviewed by: jhb
Pointy hat to: kib
MFC after: 1 week
Wakeup the thread doing the fdc_detach() when the fdc worker thread exits [1].
Write access to the write-protected floppy shall call device_unbusy() to
pair the device_busy() in the fd_access() [2].
PR: 116537 [1], 116539 [2]
MFC after: 1 week
rspq lock. Not doing so was causing us to skip re-enabling the interrupt.
- remove duplicate credits sysctl
- add support for dumping hardware context of the txq
- decrement budget_left when we break out of the process_responses loop
interrupt handlers for child devices by adding a dummy handler that is
always present so that the underlying interrupt thread is always around
avoiding panics from stray interrupts.
MFC after: 3 days
Remove this argument and pass curthread directly to underlying
VOP_LOCK1() VFS method. This modify makes the code cleaner and in
particular remove an annoying dependence helping next lockmgr() cleanup.
KPI results, obviously, changed.
Manpage and FreeBSD_version will be updated through further commits.
As a side note, would be valuable to say that next commits will address
a similar cleanup about VFS methods, in particular vop_lock1 and
vop_unlock.
Tested by: Diego Sardina <siarodx at gmail dot com>,
Andrea Di Pasquale <whyx dot it at gmail dot com>
- return the error from cxgb_tx_common so that when an error is hit we dont
spin forever in the taskq thread
- remove unused rxsd_ref
- simplify header_offset calculation for embedded mbuf headers
- fix memory leak by making sure that mbuf header initialization took place
- disable printf's for stalled queue, don't do offload/ctrl queue restart
when tunnel queue is restarted
- add more diagnostic information about the txq state
- add facility to dump the actual contents of the hardware queue using sysctl
Now, lockmgr() function can only be called passing curthread and the
KASSERT() is upgraded according with this.
In order to support on-the-fly owner switching, the new function
lockmgr_disown() has been introduced and gets used in BUF_KERNPROC().
KPI, so, results changed and FreeBSD version will be bumped soon.
Differently from previous code, we assume idle thread cannot try to
acquire the lockmgr as it cannot sleep, so loose the relative check[1]
in BUF_KERNPROC().
Tested by: kris
[1] kib asked for a KASSERT in the lockmgr_disown() about this
condition, but after thinking at it, as this is a well known general
rule, I found it not really necessary.
This makes it possible to support ftruncate() on non-vnode file types in
the future.
- 'struct fileops' grows a 'fo_truncate' method to handle an ftruncate() on
a given file descriptor.
- ftruncate() moves to kern/sys_generic.c and now just fetches a file
object and invokes fo_truncate().
- The vnode-specific portions of ftruncate() move to vn_truncate() in
vfs_vnops.c which implements fo_truncate() for vnode file types.
- Non-vnode file types return EINVAL in their fo_truncate() method.
Submitted by: rwatson
set, announce BIO_DELETE capability and issue ATA_CFA_ERASE when we get one.
Once we issue more BIO_DELETE, this will improve lifetime, and
possibly write speed of Flash based devices which have usable flash
adaptation layers.
For now, about the only usage is the newfs(1) -E flag.
Approved by: sos
peoples code with irrelevant changes[1]:
Use bus_{read|write_*() instead of bus_space_{read|write}_*() for
purely stylistic reasons.
Due to compiler optimizations and inlining, this is for all practical
purposes without effect in the compiled code.
[1] NB: Approved by: sos
of two compares against 0. The negative effect of cache flushing
is probably more than the gain by not doing the two compares (the
value is almost certainly in register or at worst, cache).
Note that the uses of m_freem() are in error cases and m_freem()
handles NULL anyhow. So fast-path really isn't changed much at all.
correct number of acpi_thermalX devices. Having this wrong caused the
acpi_thermal thread to realloc the array of devices on each loop iteration.
MFC after: 1 week
PR: kern/118497
Submitted by: Pasi Parviainen
- Introduce a finit() which is used to initailize the fields of struct file
in such a way that the ops vector is only valid after the data, type,
and flags are valid.
- Protect f_flag and f_count with atomic operations.
- Remove the global list of all files and associated accounting.
- Rewrite the unp garbage collection such that it no longer requires
the global list of all files and instead uses a list of all unp sockets.
- Mark sockets in the accept queue so we don't incorrectly gc them.
Tested by: kris, pho
possible to end up in the interrupt handler again while processing the
previous RX interrupt in ifp->if_input() because the MD interrupt code
disables the delivery of the respective interrupt until all associated
handlers were called (in the INTR_FILTER case the MI code supposedly
does the same). Toggling the NIC interrupt enable bit in these handlers
still is necessary though as some chips (f.e. the VMware emulated one)
require this to be done in order to keep issuing interrupts.
MFC after: 1 month
implemented with macros. This patch improves code readability. Reasoning
behind vidd_* is a sort of "video discipline".
List of macros is supposed to be complete--all methods of video_switch
ought to have their respective macros from now on.
Functionally, this code should be no-op. My intention is to leave current
behaviour of touched code as is.
No objections: rwatson
Silence on: freebsd-current@
Approved by: cognet
implemented with macros. This patch improves code readability. Reasoning
behind kbdd_* is a "keyboard discipline".
List of macros is supposed to be complete--all methods of keyboard_switch
should have their respective macros from now on.
Functionally, this code should be no-op. My intention is to leave current
behaviour of code as is.
Glanced at by: rwatson
Reviewed by: emax, marcel
Approved by: cognet
- Use the correct offsets when copying out the results of PCIOCGETCONF_OLD.
This happened to not affect the 64-bit architectures because there the
addition of pc_domain to struct pcisel didn't change the overall size of
struct pci_conf. [1]
- Always copy the name and unit information to conf_old so it's also part
of the output once this information is cached in dinfo.
- Use the correct type for flags in struct pci_match_conf_old. This
change is more or less cosmetic though.
Reported and tested by: bde [1]
Reviewed by: imp
MFC after: 3 days
Committed from: 24C3
If a mouse has both a wheel and a Z direction we report both.
XXX Due to tradition the wheel is reported as the Z direction (and the Z
direction as W).
Now Apple's Mighty Mouse is fully supported, except the X11 mouse driver
doesn't know what to do with the new coordinate.
MFC after: 3 months
Approved by: njl (mentor), imp
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
fget() call, that is sleeping point, and possibly dropping Giant.
The snp_target == NULL implies the snp_tty == NULL. Remove the code
that is put under snp_target == NULL and snp_tty != NULL clause.
In snpclose(), do the snp_detach() before scheduling the snp device
destruction. Otherwise, after the return from snpclose(), the snp
device is already removed from the snp_list, but tty is still in
snooped state. Any attempt to do i/o on such tty cause panic because
ttytosnp() returns NULL.
Tested by: Peter Holm
MFC after: 1 week
as multicast/broadcast frames. Previously re(4) ignored multicast
frames in promiscuous mode. The RTL8169 datasheet was not clear
how it handles multicast frames in promiscuous mode.
PR: kern/118572
MFC after: 3 days
NULL and doesn't point to a NULL pointer before dereferencing it. This
fixes a panic triggered by Xorg 7.3.
Reported and tested by: Bill Green
MFC after: 3 days
a pointer to struct bus_space. The structure contains function
pointers that do the actual bus space access.
The reason for this change is that previously all bus space
accesses were little endian (i.e. had an explicit byte-swap
for multi-byte accesses), because all busses on Macs are little
endian.
The upcoming support for Book E, and in particular the E500
core, requires support for big-endian busses because all
embedded peripherals are in the native byte-order.
With this change, there's no distinction between I/O port
space and memory mapped I/O. PowerPC doesn't have I/O port
space. Busses assign tags based on the byte-order only.
For that purpose, two global structures exist (bs_be_tag and
bs_le_tag), of which the address can be taken to get a valid
tag.
Obtained from: Juniper, Semihalf
is actually a circular log. Deal with it rolling around. Fortunately,
the log area is big and I haven't seen any roll over yet. Update and
get rid of the obsolete comment.
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
it's multi DAC / playback channels is not that good. Enabling vchans
make the bug more visible since playback allocation will look for
possible free hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has been proven faulty.
Tested by: Dominic Fandrey <LoN_Kamikaze at gmx dot de>
URL: http://lists.freebsd.org/pipermail/freebsd-stable/2007-December/039022.html
The HT1000 DMA engine seems to not always like 64K transfers and sometimes barfs data all over memory leading to instant chrash and burn.
Also fix 48bit adressing issues, apparently newer chips needs 16bit writes and not the usual fifo thing.
HW donated by: Travis Mikalson at TerraNovaNet
that favours true hardware channel, the first instance of recording
request will grab this channel (the first channel is being used as
vchan master). In many cases, it is not really work as intended and give
false impression of broken recording.
PR: kern/118546
MFC after: 3 days
Ethernet Controller. Multicast filtering wasn't tested and needs more
expore. While I'm here change complex if statements with switch
statement which would improve readability.
Reported by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
Tested by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
pass back the desired buffer length. This fixes scanning with the Marvell
88W8335 and BCM4328 wireless cards.
PR: kern/118370
Submitted by: Weongyo Jeong
Tested by: Ed Schouten
by Daniel Kamm.
Adaptec RAID 51245
Adaptec RAID 51645
Adaptec RAID 52445
Adaptec RAID 5405
Sun STK RAID REM
Sun STK RAID EM
SG-XPCIESAS-R-IN
SG-XPCIESAS-R-EX
initialized before use and returned integrally instead of up to size.
Submitted by: Ilja van Sprundel <ilja -at- netric.org>
Reviewed by: secteam
MFC after: 1 day
is what gcc3 complains about.
Without this change, it's impossible to build the kernel with gcc3.
Tested by: cognet@ (mentor)
Approved by: cognet@ (mentor)
attached. Otherwise, the snp->snp_tty would be overwritten, while the
tty line discipline still set to the snpdisc. Then snplwrite() causes
panic because ttytosnp() cannot find the snp.
MFC after: 1 week
sx driver), change a magic value in the PLX bridge chip. Apparently later
builds of the PCI cards had corrected values in the configuration eeprom.
This change supposedly fixes some pci bus problems.
hack means you can get the units and flags to match up more easily with
serial consoles on machines with acpi tables that cause the com ports
to be probed in the wrong order (and hence get the wrong sio unit number).
This replaces the common alternative hack of editing the code to comment
out the acpi attachment. This could go away entirely when device wiring
patches are committed.
stomping on the units intended for the motherboard sio ports. This is
no real substitute for the not-yet-committed device wiring enhancements.
Code taken from sio's pci attachment.
Intel CPUs with family 0x6, model 0xE and later (i.e., Intel Core(TM))
have a PMC architecture that differs somewhat from previous CPUs in
family 0x6. Even though the basic programming model is similar, the
documented set of legal values that may be loaded into their PMC MSRs
differs from that of the previous PMCs in family 0x6 and reusing bit
values valid for the older PMCs could result in undefined behaviour in
the general case.
T_DIRECT filtering so that disk drives can be attached via the
pass driver. Add CAM locking. Don't mark CAM commands as SG64
since the hardware isn't designed to deal with 64-bit passthru
commands. Hopefully the bounce buffer changes that were done
for the management/ioctl interface are robust enough to handle
this deficiency for CAM as well.
- Enable pcbeep control for Acer + ALC268 (nid 29). Give enough (fake)
hints so the parser will grab it and allocate "speaker" control.
- Fix regression while preparing DAC and ADC for multichannel
format. Since playback policy is to output to every possible path,
ensure that each DAC is started.
Reported / Tested by: Guy Brand
The call should happen with the driver lock held. We don't hold the driver
lock in newstate as it's a separate thread where we can't sleep (and we only
call wpi_cmd in async mode).
Discovered By: Attillo's callout rework
Approved By: mlaier (comentor)
o Acer Aspire 4520 laptop
- jack sensing / automute
o Toshiba Satellite A135-S4527 laptop
- jack sensing / automute
Tested by: lioux
o Apple Macbook 3 (is it?)
- require gpio0 (for speakers) and ovref50 (for headphone)
to make it works
- jack sensing / automute
Tested by: Ed Schouten
* Add Nvidia MCP67 controller ids.
* Be sensible about simmilar controller with multiple pci ids.
* Connect unused DAC/ADC to stream#0 rather than forcing each of them
managing their own stream.
MFC after: 3 days
- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
- Trying to eliminate another racing by replacing the timeout(9) with
callout APIs. In addition to that, the callout_drain() in an_detach()
help us to avoid a possible panic-on-free due to the callout API tries
to lock a destroyed mutex.
- In an_stats_update(), check the return value of an_read_record(). This
should reduce the chance of device removal(PCCARD) panic [2].
- Adding a comment to state the fact that an_stats_update() is now called
via callout(9) with a lock held [2].
Submitted by: jhb [1], ambrisko [2]
Reviewed by: jhb, ambrisko
Reported by: dhw
Tested by: dhw
MFC after: 3 days
priorities of the technologies supported by 802.3 Selector Field
value.
1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T
However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.
PR: 92599
that the driver will handle WEP encryption. However, this does not seem to be
implemented by this driver (or maybe the chipset doesn't support it?)
Removing the flag makes my wpi card work using wpa_supplicant(8) on a
network with 802.1x security (without this change it authenticated fine, but
tcpdump only saw garbage packets)
Reviewed by: benjsc, imp (mentor)
Approved by: imp (mentor), sam
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
and update the rx code to handle multiple frames in a single usb
transfer. AX772 parts (at least) exhibit many input errors when
operated with a 2K rx buffer and no errors w/ a 4K rx buffer (it's
unclear what the cause of the errors is for 2K so this may just be
covering up the real issue). Larger rx buffer sizes show no
significant performance improvement for AX772. Bypassing the common
buffer management routines also eliminates an extra context switch
on every packet which noticeably improves performance (TCP netperf
rx goes from 45 Mb/s to 85 MB/s).
Submitted by: "J.R. Oldroyd" <fbsd@opal.com>
Reviewed by: imp
Obtained from: openbsd (partly)
MFC after: 3 weeks
The reliability of it's multi DAC / playback channels is
not that good. Enabling vchans make the bug more visible
since playback allocation will look for possible free
hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has
been proven faulty.
Reported / Tested by: Sascha Klauder
MFC after: 3 days
- Patch registers CR47 and CR157 on devices that require it.
- Fix power calibration setting on ZD1211B.
Obtained from: OpenBSD
- Fix multicast transfer by properly reprogram multicast global
hash table, which in turns fix promiscuous mode and IPv6
autoconfiguration / local networking.
Reviewed by: sam, Weongyo Jeong
Tested using: Aztech WL230 , Belkin F5D7050, Unicorn WL-54G,
3COM 3CRUSB10075
MFC after: 1 week
I've tried to move md(4) to use geom_disk class, like real disks do, but
this requires major rework of some of the existing features such as
configuration dumping for example. Therefore just putting devstat support
directly into md(4) seems to be optimal solution.
Now you can see md(4) stats in `systat -vm' again.
MFC after: 2 weeks
present on the MacBook, MacBook Pro, and Intel MacMini.
This driver exports information via sysctl in its private sysctl tree
dev.asmc.*. You can get information about temperatures, fan speeds, the
keyboard light sensor and the Sudden Motion Sensor (SMS).
The SMS is very useful to park the disk heads when the laptop is
moved. Basically, the SMS is setup so that, under movement, we get an
interrupt on irq 6 and a devd notification is sent.
Sponsored by: Google Summer of Code 2007
Approved by: njl (mentor)
Reviewed by: attilio (previous version, but very similar), jhb (interrupt
specific review)
while other variants have inorder ethernet address for the same
chipset. Override ethernet address ordering if we already know how
it was stored. This fixes the use of inversed ethernet address on
MCP67.
Submitted by: ariff
MFC after: 3 days
Allocate space in keyboard state structure instead to prevent random byte
from possibly overwritten stack location frombeing shoved into USB device
when transfer actually takes place.
This fixes at least one instance of LEDs not working with USB keyboards.
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
reset problem when we reboot the system with the zyd device inserted.
Submitted by: Weongyo Jeong
Reported by: Ted Lindgreen (ted@tednet.nl)
MFC after: 1 week
