an unused pageq queue reference in the page structure to stash a pointer
to the MemGuard FIFO. Using the page->object field caused problems
because when vm_map_protect() was called the second time to set
VM_PROT_DEFAULT back onto a set of pages in memguard_map, the protection
in the VM would be changed but the PMAP code would lazily not restore
the PG_RW bit on the underlying pages right away (see pmap_protect()).
So when a page fault finally occured and the VM noticed the faulting
address corresponds to a page that _does_ have write access now, it
would then call into PMAP to set back PG_RW (i386 case being discussed
here). However, before it got to do that, an assertion on the object
lock not being owned would get triggered, as the object of the faulting
page would need to be locked but was overloaded by MemGuard. This is
precisely why MemGuard cannot overload page->object.
Submitted by: Alan Cox (alc@)
the rate for the 100% state once. Afterwards, use that value for deriving
states. This should fix the problem where the calibrated frequency was
different once a switch was done, giving a different set of levels each
time. Also, properly search for the right cpufreqX device when detaching.
parent cpu device before passing it to pcpu_find(). Get the ivars from the
child, not parent cpu device. These bugs would cause a panic when
dereferencing the pcpu ivar, but weren't present in the acpi attachment
which it seems most people are using.
and into the bus front ends. For ISA and C-BUS cards, we always need
to grab it. For PC Card, already committed, we need to do some sanity
checking on the data that's in the ROMs before we decide that they are
OK to use. The PC Card code has already been committed and is
independent of this code (which also has to work on NE-1000 cards,
assuming that those cards still work :-).
with the latest changes. They actually have valid ROM data at location
0 of memory, just like a real NE-2000 ISA card. Use this data, if
the ROM passes a few basic tests, as an additional source for the MAC
address. Prefer the CIS over this source, but have it take precidence
over falling back to reading the attribtue memory.
o Minor cleanup of a few devices that we match on based on CIS string.
Remove the SACK "initburst" sysctl.
- Fix bugs in SACK dupack and partialack handling that can cause
large bursts while in SACK recovery.
Submitted by: Mohan Srinivasan
override the current freq level temporarily and restore it when the
higher priority condition is past. Note that only the first overridden
value is saved. Callers pass NULL to CPUFREQ_SET to restore the saved
level. Priorities are not yet used so this commit should have no effect.
- refactor ngd_constructor, so that make_dev() is called without
any locks held, since it mallocs memory with M_WAITOK flag.
- rename global mtx, to have name different to per-node mtx
MFC after: 2 weeks
removes netgraph node and unwraps Ethernet interface.
This gives us ability to unload ng_ether.ko, when all interfaces
are detached, making ng_ether(4) developers happy.
Reviewed by: ru
driver did VLAN decapsulation in hardware, we were passing a frame
as if it came for the parent (non-VLAN) interface. Stop this from
happening.
Reminded by: glebius
Security: This could pose a security risk in some setups
o Use SYSCTL_IN() macro instead of direct call of copyin(9).
Submitted by: ume
o Move sysctl_drop() implementation to sys/netinet/tcp_subr.c where
most of tcp sysctls live.
o There are net.inet[6].tcp[6].getcred sysctls already, no needs in
a separate struct tcp_ident_mapping.
Suggested by: ume
bridge between OLDCARD and NEWCARD for drivers to inquire after the
function number (eg, 0, 1, 2). Nobody ever used it, so retire it
with honors. NEWCARD never implemented it, and the same information
can be obtained by the pccard_get_function_number().
MFC After: 3 days
proper way, or at least the same way that NetBSD and Linux do things
(I've been unable to obtain datasheets for these parts to know for
sure). This has some marginal improvement in the DL10022 and DL10019
cards that I have. Also, report which type, exactly.
# There's one or two ed cards that I have which still don't work, but I think
# that's due to MII losage on the card that's not presently compensated
# for in the MII drivers.
tree since 2003/02/20, and I recently cleaned it up. I'd even closed
the PR that I obtained this from Fri Jul 18 23:25:08 MDT 2003 since
I looked at my p4 tree.
PR: 46889
Submitted by: HASEGAWA Tomoki
memory disk is larger than the number of available sf_bufs, this improves
performance on SMPs by eliminating interprocessor TLB shootdowns. For
example, with 6656 sf_bufs, the default on my test machine, and a 256MB
swap-backed memory disk, I see the command
"dd if=/dev/md0 of=/dev/null bs=64k" achieve ~489MB/sec with the default,
shared mappings, and ~587MB/sec with CPU private mappings.
base transfer speed to CAM. The actual value used (40MB/s) is fairly
arbitrary, but assumes the same 33% overhead as was implied by the
1MB/s figure we used for USB1 devices.
are not added to the list(s) of available settings. However, other drivers
can call the CPUFREQ_DRV_SETTINGS() method on those devices directly to
get info about available settings.
Update the acpi_perf(4) driver to use this flag in the presence of
"functional fixed hardware." Thus, future drivers like Powernow can
query acpi_perf for platform info but perform frequency transitions
themselves.
on dev.cpu.0 will affect all of the CPUs together. In the future,
independent control will be supported but this is good enough for now.
Check that the timecounter isn't TSC before switching (from Colin Percival.)
former is callable from user space and the latter from the kernel one. Make
kernel version take additional argument which tells if the respective call
should check for additional restrictions for sending signals to suid/sugid
applications or not.
Make all emulation layers using non-checked version, since signal numbers in
emulation layers can have different meaning that in native mode and such
protection can cause misbehaviour.
As a result remove LIBTHR from the signals allowed to be delivered to a
suid/sugid application.
Requested (sorta) by: rwatson
MFC after: 2 weeks
throttling, neglecting to do this kept the sysctls from appearing.
Attach an acpi_throttle device to each CPU that supports it.
Don't add a device if the P_BLK is invalid or if _PTC is not present.
This removes extraneous probe/attach failure messages on some machines.
Make the cpu throttle state local to the softc to account for partial
successes when changing the clock rate on MP machines.
for nodes hanging off of Central (untested), FireHose (untested) and
PCI (tested) busses.
- Add an additional parameter to OF_decode_addr() which specifies the
index of the register bank to decode.
These should allow to eventually add support for the Z8530 hanging off of
FireHose to uart(4) and to write support for PCI-based graphics adapters.
Suggested by: tmm (back in '03)
which will finally lead to kernel panic.
Security: This prevents a local (root-launched) DoS
Submitted by: Wojciech A. Koszek [dunstan at freebsd czest pl]
PR: 77421
MFC After: 1 week
o Add a fallback location for the MAC address. Most of the early ne2000
PC Cards were built from the same parts, so most of them have the same
address in the CIS to grab the MAC from. Use this address as our
fallback if we don't find anything better.
o Add printf, in bootverbose, noting the MAC addresses that we find along
the way.
# Better sanity checking of the MAC address is needed. Will have to
# investigate using/creating a centralized function to do this as a number
# of other PC Card drivers each have their own ad-hoc tests.
a definite setup was broken: two ng_ksockets are connected to each other,
connect()ed to different remote hosts, and bind()ed to different local
interfaces. In this case one ng_ksocket is fooled with tag from the other
one.
Put node id into tag. In rcvdata method utilize tag only if it has our
own id inside or id equals zero. The latter case is added to support
packets send by some third, not ng_ksocket node.
MFC after: 1 week
1. Dependency on netgraph module was broken (wrong version).
2. Netgraph node type was never destroyed on unload. This
was masked by problem #1.
Fixed both by using NETGRAPH_INIT(). Now netgraph node type
is created on module load, as in the rest of netgraph modules.
This information will be very useful for people who are tuning applications
which have a dependence on IPC mechanisms.
The following OIDs were documented:
Message queues:
kern.ipc.msgmax
kern.ipc.msgmni
kern.ipc.msgmnb
kern.ipc.msgtlq
kern.ipc.msgssz
kern.ipc.msgseg
Semaphores:
kern.ipc.semmap
kern.ipc.semmni
kern.ipc.semmns
kern.ipc.semmnu
kern.ipc.semmsl
kern.ipc.semopm
kern.ipc.semume
kern.ipc.semusz
kern.ipc.semvmx
kern.ipc.semaem
Shared memory:
kern.ipc.shmmax
kern.ipc.shmmin
kern.ipc.shmmni
kern.ipc.shmseg
kern.ipc.shmall
kern.ipc.shm_use_phys
kern.ipc.shm_allow_removed
kern.ipc.shmsegs
These new descriptions can be viewed using sysctl -d
PR: kern/65219
Submitted by: Dan Nelson <dnelson at allantgroup dot com> (modified)
No objections: developers@
Descriptions reviewed by: gnn
MFC after: 1 week
at some offset. Unlike newer cards, the MAC address wasn't part of
the CIS as a specific FUNCE. These older cards were having their MAC
address show up as 0:2:4:6:8:a because that's what's in the ROM
locations that would be there in a real ne2000.
This patch allows one to specify the offset for the MAC address for
these cards. Specify one for the IBM Ethernet II card, as it is one
that has this problem. One shouldn't specify this unless the MAC
address really isn't in the CIS at all.
Side note: The novell probe likely shouldn't read the MAC address, and
that should be moved to the bus specific attach routine(s), maybe as a
convenience function in if_ed_novell.c.
My IBM Ethernet II (aka Info Mover) now has a believable MAC address.
with net byte order. Change byte order to net in ng_ipfw_input(), change
byte order to host before ip_output(), do not change before ip_input().
In collaboration with: ru
suid application. The problem is that Linux applications using old Linux
threads (pre-NPTL) use signal 32 (linux SIGRTMIN) for communication between
thread-processes. If such an linux application is installed suid or sgid
and security.bsd.conservative_signals=1 (default), then permission will be
denied to send such a signal and the application will freeze.
I believe the same will be true for native applications that use libthr,
since libthr uses SIGTHR for implementing conditional variables.
PR: 72922
Submitted by: Andriy Gapon <avg@icyb.net.ua>
MFC after: 2 weeks
are NOVELL NE2000 with just a tiny quirk that's non vendor specific.
Instead, use the chip_type of DL100XX instead. This is more inline
with how the AX88190 support was added, and seems a little cleaner.
can retransmit on TX underrun and set TOK in addition to TUND. Also add a
check to prevent overflow of the addressable threshold.
This fixes some reports of rl(4) slowness, believed to be related to ALTQ
before.
PR: kern/61448
Submitted by: Tim Draegen-Gilman <timNOeudaemonSPAMnet> (with changes)
MFC after: 1 week
list, set `curr_callout' to NULL. This ensures that we won't attempt
to cancel the current callout if the original callout structure
gets recycled while we wait to acquire Giant.
This is reported to fix an intermittent syscons problem that was
introduced by revision 1.96.
pessmize the error recover path through edintr by calling these
functions, rather than expanding it inline. This error path already
does a lot in it, so an extra function call will be lost in the noise.
It also happens rarely.
while (complicated-expr)
continune;
in preference to
while (complicated-expr);
since the code generated is identical, and the former is easier to read,
especially for complicated-expr that reach to the end of the line...
a little bit of complexity but performance requirements lacking (this is
a debugging allocator after all), it's really not too bad (still
only 317 lines).
Also add an additional check to help catch really weird 3-threads-involved
races: make memguard_free() write to the first page handed back, always,
before it does anything else.
Note that there is still a problem in VM+PMAP (specifically with
vm_map_protect) w.r.t. MemGuard uses it, but this will be fixed shortly
and this change stands on its own.
Older cards have it reversed.
Also, use some already defined values instead of magic numbers.
PR: 73324
Submitted by: arne_woerner@yahoo.com
MFC after: 1 week
do not need to perform an extra memory fetch in the Packet (Mbuf+Cluster)
constructor to initialize the reference counter anymore. The reference
counts are located in a separate memory region (in the slab header,
because this zone is UMA_ZONE_REFCNT), so the memory fetch resulted very
often in a cache miss. Additionally, and perhaps more significantly,
optimize the free mbuf+cluster (packet) case, which is very common, to
no longer require an atomic operation on free (to verify the reference
counter) if the reference on the cluster has never been increased (also
very common). Reduces an atomic on mbuf free on average.
Original patch submitted by: Gerrit Nagelhout <gnagelhout@sandvine.com>
fix the problem with device discovery seen by some people.
2. Change to make 3ware CLI/3DM work on amd64.
3. Fix a potential problem that could cause the driver to do strlen(NULL) when
using older firmware.
Reviewed by:scottl
probing the novell ne[12]000 cards. It should be its own thing, ala
how we do the dl100xx support doing its own thing at the right time.
For the moment, it is just a function, which makes the mainline of the
generic probe easier to follow.
Also, correct a couple of comments that looked wrong.
# there may be a bug in setting up gwether, in that we set
# sc->rec_page_stop based on memsize, rather than sc->mem_size, so if
# these two are different, then the rec_page_stop will be wrong. I'm
# hesitant to fix it without real hardware to test with. Since
# gwether isn't in the hardware list of the man page nor in the commit
# messages, it is hard to know for sure.
