SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
- Replace divisor numbers with more descirptive names
- Properly calculate minimum frequency for SDHCI 3.0
- Properly calculate frequency for SDHCI 3.0 in mmcbr_set_clock
- Add min_freq method to sdhci_if.m and provide default
implementation. By re-implementing this method hardware
drivers can control frequency controller operates when
executing initialization sequence
actually do have to reinitialise the RX side of things after an RX
descriptor EOL error.
* Revert a change of mine from quite a while ago - don't shortcut the
RX initialisation path. There's a RX FIFO bug in the earlier chips
(I'm not sure when it was fixed in this series, but it's fixed
with the AR9380 and later) which causes the same RX descriptor to
be written to over and over. This causes the descriptor to be
marked as "done", and this ends up causing the whole RX path to
go very strange. This should fixed the "kickpcu; handled X packets"
message spam where "X" is consistently small.
When a cylinder group runs short of inodes, a new block for inodes is
allocated, zero'ed, and written to the disk. The zero'ed inodes must
be on the disk before the cylinder group can be updated to claim them.
If the cylinder group claiming the new inodes were written before the
zero'ed block of inodes, the system could crash with the filesystem in
an unrecoverable state.
Rather than adding a soft updates dependency to ensure that the new
inode block is written before it is claimed by the cylinder group
map, we just do a barrier write of the zero'ed inode block to ensure
that it will get written before the updated cylinder group map can
be written. This change should only slow down bulk loading of newly
created filesystems since that is the primary time that new inode
blocks need to be created.
Reported by: Robert Watson
Reviewed by: kib
Tested by: Peter Holm
write is a disk write request that tells the disk that the buffer
being written must be committed to the media along with any writes
that preceeded it before any future blocks may be written to the drive.
Barrier writes are provided by adding the functions bbarrierwrite
(bwrite with barrier) and babarrierwrite (bawrite with barrier).
Following a bbarrierwrite the client knows that the requested buffer
is on the media. It does not ensure that buffers written before that
buffer are on the media. It only ensure that buffers written before
that buffer will get to the media before any buffers written after
that buffer. A flush command must be sent to the disk to ensure that
all earlier written buffers are on the media.
Reviewed by: kib
Tested by: Peter Holm
From: Jouni Malinen <j@w1.fi>
Date: Fri, 15 Jul 2011 13:42:06 +0300
Subject: [PATCH] MD5: Fix clearing of temporary stack memory to use correct length
sizeof of the structure instead of the pointer was supposed to be used
here. Fix this to clear the full structure at the end of MD5Final().
Found by: clang ToT
Reviewed by: rpaulo
MFC after: 3 days
X86: Disable generation of rep;movsl when %esi is used as a base pointer.
This happens when there is both stack realignment and a dynamic alloca in the
function. If we overwrite %esi (rep;movsl uses fixed registers) we'll lose the
base pointer and the next register spill will write into oblivion.
Fixes PR15249 and unbreaks firefox on i386/freebsd. Mozilla uses dynamic allocas
and freebsd a 4 byte stack alignment.
MFC after: 1 week
blocking modes described in section 3.4.3 of RFC 2783, allowing the caller
to retrieve the most recent values without blocking, to block for a specified
time, or to block forever.
Reviewed by: discussion on hackers@
length packets, which was actually harmless.
Note that peers with different version of head/ may grow this
counter, but it is harmless - all pfsync data is processed.
Reported & tested by: Anton Yuzhaninov <citrin citrin.ru>
Sponsored by: Nginx, Inc
* The following bit flags where incroccetly defined:
o Mesh Control Present
o Mesh Power Save Level
o RSPI
This is now corrected according to Table 8.4 as per IEEE 802.11 2012;
Approved by: adrian (mentor)