clock found on the ISA bus (some USIIe, USIIi and USIIIi models) and
EBus (USIII models) instead of a MK48Txx clock.
Testet by: Matthew T. Lager" <freebsd@trinetworks.com> on Sun Fire V100,
Xavier Beaudouin <kiwi@oav.net> on Netra X1 (initial version)
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
be used to announce various system activity.
The auxio device provides auxiliary I/O functions and is found on various
SBus/EBus UltraSPARC models. At present, only front panel LED is
controlled by this driver.
Approved by: jake (mentor)
Reviewed by: joerg
Tested by: joerg
for EBus, ISA and PCI, by compiling ofw_isa.c and ofw_pci_if.m unconditio-
nally. The correct way is to rewrite OF_decode_addr() in ofw_machdep.c in
a bus-neutral way. That's certainly possible but we unfortunately didn't
make it for FreeBSD 5.3.
Approved by: tmm
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.
Approved by: tmm, no objections on freebsd-sparc64
implementation could be characterized as a hybrid of the amd64 and i386
implementations. Specifically, the direct virtual-to-physical mapping is
used if possible and sf_buf_alloc() is used if the direct map cannot.
of what uart(4) is and/or is not see the initial commit log of one
of the files in sys/dev/uart (or see share/man/man4/uart.4).
Note that currently pc98 shares the MD file with i386. This needs
to change when pc98 support is fleshed-out to properly support the
various UARTs. A good example is sparc64 in this respect.
We build uart(4) as a module on all platforms. This may break
the ppc port. That depends on whether they do actually build
modules.
To use uart(4) on alpha, one must use the NO_SIO option.
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.
The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.
There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.
A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.
In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.
In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.
Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris
on future UltraSPARC cpus for which the data cache is not direct mapped.
- Move UltraSPARC I and II (spitfire, blackbird, sapphire, sabre) specific
functions to spitfire.c, and add cheetah.c for UltraSPARC III specific
functions. Initially just cache flushing, but there are a few other
functions that will need to move here.
- Add an ipi handler for data cache flushing on UltraSPARC III.
- Use function pointers to select the right cache flushing functions based
on cpu_impl.
With this it is possible to boot single user from an mfs root on UltraSPARC
III systems, including spinning up secondary processors. There is currently
no support for the host to pci bridge, and no documentation for it is
publically available.
Thanks to Oleg Derevenetz for providing access to a system with UltraSPARC
III+ cpus.
UltraSPARCs, and an eeprom attachment for fhc, which allows the date
to be set properly on these machines. Central is a wierd bus which
seems to only ever have 1 fhc attached to it. FHC (FireHose Controller)
is another wierd bus with various things on it depending where its attached.
The fhc attached to central has eeprom and zs, and the fhcs which attach
directly to nexus have simm-status, environment and other nodes, none of
which I'll probably ever have documentation for.
Thanks to Ade Lovett for providing access to an 8 cpu e4500.
as sparc64/sparc64/dump_machdep.c a while back).
Other than ia64 (which uses ELF), sparc64 uses a homegrown format for
the dumps (headers are required because the physical address and size of
the tsb must be noted, and because physical memory may be discontiguous);
ELF would not offer any advantages here.
Reviewed by: jake
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
the pv lists in the vm_page, even unmanaged kernel mappings. This is so
that the virtual cachability of these mappings can be tracked when a page
is mapped to more than one virtual address. All virtually cachable
mappings of a physical page must have the same virtual colour, or illegal
alises can be created in the data cache. This is a bit tricky because we
still have to recognize managed and unmanaged mappings, even though they
are all on the pv lists.
disablement assumptions in kern_fork.c by adding another API call,
cpu_critical_fork_exit(). Cleanup the td_savecrit field by moving it
from MI to MD. Temporarily move cpu_critical*() from <arch>/include/cpufunc.h
to <arch>/<arch>/critical.c (stage-2 will clean this up).
Implement interrupt deferral for i386 that allows interrupts to remain
enabled inside critical sections. This also fixes an IPI interlock bug,
and requires uses of icu_lock to be enclosed in a true interrupt disablement.
This is the stage-1 commit. Stage-2 will occur after stage-1 has stabilized,
and will move cpu_critical*() into its own header file(s) + other things.
This commit may break non-i386 architectures in trivial ways. This should
be temporary.
Reviewed by: core
Approved by: core
