1. ICMP ECHO and TSTAMP replies are now rate limited.
2. RSTs generated due to packets sent to open and unopen ports
are now limited by seperate counters.
3. Each rate limiting queue now has its own description, as
follows:
Limiting icmp unreach response from 439 to 200 packets per second
Limiting closed port RST response from 283 to 200 packets per second
Limiting open port RST response from 18724 to 200 packets per second
Limiting icmp ping response from 211 to 200 packets per second
Limiting icmp tstamp response from 394 to 200 packets per second
Submitted by: Mike Silbersack <silby@silby.com>
only be checked if the system is currently performing New Reno style
fast recovery. However, this value was being checked regardless of the
NR state, with the end result being that the congestion window was never
opened.
Change the logic to check t_dupack instead; the only code path that
allows it to be nonzero at this point is NewReno, so if it is nonzero,
we are in fast recovery mode and should not touch the congestion window.
Tested by: phk
delete the cloned route that is associated with the connection.
This does not exhaust the routing table memory when the system
is under a SYN flood attack. The route entry is not deleted if there
is any prior information cached in it.
Reviewed by: Peter Wemm,asmodai
code retransmitting data from the wrong offset.
As a footnote, the newreno code was partially derived from NetBSD
and Tom Henderson <tomh@cs.berkeley.edu>
better recovery for multiple packet losses in a single window.
The algorithm can be toggled via the sysctl net.inet.tcp.newreno,
which defaults to "on".
Submitted by: Jayanth Vijayaraghavan <jayanth@yahoo-inc.com>
Now most big problem of IPv6 is getting IPv6 address
assignment.
6to4 solve the problem. 6to4 addr is defined like below,
2002: 4byte v4 addr : 2byte SLA ID : 8byte interface ID
The most important point of the address format is that an IPv4 addr
is embeded in it. So any user who has IPv4 addr can get IPv6 address
block with 2byte subnet space. Also, the IPv4 addr is used for
semi-automatic IPv6 over IPv4 tunneling.
With 6to4, getting IPv6 addr become dramatically easy.
The attached patch enable 6to4 extension, and confirmed to work,
between "Richard Seaman, Jr." <dick@tar.com> and me.
Approved by: jkh
Reviewed by: itojun
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
-opt_ipsec.h was missing on some tcp files (sorry for basic mistake)
-made buildable as above fix
-also added some missing IPv4 mapped IPv6 addr consideration into
ipsec4_getpolicybysock
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
packet divert at kernel for IPv6/IPv4 translater daemon
This includes queue related patch submitted by jburkhol@home.com.
Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
- eliminate the fast/slow timeout lists for TCP and instead use a
callout entry for each timer.
- increase the TCP timer granularity to HZ
- implement "bad retransmit" recovery, as presented in
"On Estimating End-to-End Network Path Properties", by Allman and Paxson.
Submitted by: jlemon, wollmann
drop any segment arriving at a closed port.
tcp.blackhole=1 - only drop SYN without RST
tcp.blackhole=2 - drop everything without RST
tcp.blackhole=0 - always send RST - default behaviour
This confuses nmap -sF or -sX or -sN quite badly.
sysctl knobs.
With these knobs on, refused connection attempts are dropped
without sending a RST, or Port unreachable in the UDP case.
In the TCP case, sending of RST is inhibited iff the incoming
segment was a SYN.
Docs and rc.conf settings to follow.
This was missed in the 4.4-Lite2 merge.
Noticed by: Mohan Parthasarathy <Mohan.Parthasarathy@eng.Sun.COM> and
jayanth@loc201.tandem.com (vijayaraghavan_jayanth)
on the tcp-impl mailing list.
Add ICMP_BANDLIM option and 'net.inet.icmp.icmplim' sysctl. If option
is specified in kernel config, icmplim defaults to 100 pps. Setting it
to 0 will disable the feature. This feature limits ICMP error responses
for packets sent to bad tcp or udp ports, which does a lot to help the
machine handle network D.O.S. attacks.
The kernel will report packet rates that exceed the limit at a rate of
one kernel printf per second. There is one issue in regards to the
'tail end' of an attack... the kernel will not output the last report
until some unrelated and valid icmp error packet is return at some
point after the attack is over. This is a minor reporting issue only.
Any packet that can be matched by a ipfw rule can be redirected
transparently to another port or machine. Redirection to another port
mostly makes sense with tcp, where a session can be set up
between a proxy and an unsuspecting client. Redirection to another machine
requires that the other machine also be expecting to receive the forwarded
packets, as their headers will not have been modified.
/sbin/ipfw must be recompiled!!!
Reviewed by: Peter Wemm <peter@freebsd.org>
Submitted by: Chrisy Luke <chrisy@flix.net>
connect. This check was added as part of the defense against the "land"
attack, to prevent attacks which guess the ISS from going into ESTABLISHED.
The "src == dst" check will still prevent the single-homed case of the
"land" attack, and guessing ISS's should be hard anyway.
Submitted by: David Borman <dab@bsdi.com>
a hashed port list. In the new scheme, in_pcblookup() goes away and is
replaced by a new routine, in_pcblookup_local() for doing the local port
check. Note that this implementation is space inefficient in that the PCB
struct is now too large to fit into 128 bytes. I might deal with this in the
future by using the new zone allocator, but I wanted these changes to be
extensively tested in their current form first.
Also:
1) Fixed off-by-one errors in the port lookup loops in in_pcbbind().
2) Got rid of some unneeded rehashing. Adding a new routine, in_pcbinshash()
to do the initialial hash insertion.
3) Renamed in_pcblookuphash() to in_pcblookup_hash() for easier readability.
4) Added a new routine, in_pcbremlists() to remove the PCB from the various
hash lists.
5) Added/deleted comments where appropriate.
6) Removed unnecessary splnet() locking. In general, the PCB functions should
be called at splnet()...there are unfortunately a few exceptions, however.
7) Reorganized a few structs for better cache line behavior.
8) Killed my TCP_ACK_HACK kludge. It may come back in a different form in
the future, however.
These changes have been tested on wcarchive for more than a month. In tests
done here, connection establishment overhead is reduced by more than 50
times, thus getting rid of one of the major networking scalability problems.
Still to do: make tcp_fastimo/tcp_slowtimo scale well for systems with a
large number of connections. tcp_fastimo is easy; tcp_slowtimo is difficult.
WARNING: Anything that knows about inpcb and tcpcb structs will have to be
recompiled; at the very least, this includes netstat(1).
rev 1.66. This fix contains both belt and suspenders.
Belt: ignore packets where src == dst and srcport == dstport in TCPS_LISTEN.
These packets can only legitimately occur when connecting a socket to itself,
which doesn't go through TCPS_LISTEN (it goes CLOSED->SYN_SENT->SYN_RCVD->
ESTABLISHED). This prevents the "standard" "land" attack, although doesn't
prevent the multi-homed variation.
Suspenders: send a RST in response to a SYN/ACK in SYN_RECEIVED state.
The only packets we should get in SYN_RECEIVED are
1. A retransmitted SYN, or
2. An ack of our SYN/ACK.
The "land" attack depends on us accepting our own SYN/ACK as an ACK;
in SYN_RECEIVED state; this should prevent all "land" attacks.
We also move up the sequence number check for the ACK in SYN_RECEIVED.
This neither helps nor hurts with respect to the "land" attack, but
puts more of the validation checking in one spot.
PR: kern/5103
RST's being ignored, keeping a connection around until it times out, and
thus has the opposite effect of what was intended (which is to make the
system more robust to DoS attacks).
socket addresses in mbufs. (Socket buffers are the one exception.) A number
of kernel APIs needed to get fixed in order to make this happen. Also,
fix three protocol families which kept PCBs in mbufs to not malloc them
instead. Delete some old compatibility cruft while we're at it, and add
some new routines in the in_cksum family.
be dropped when it has an unusual traffic pattern. For full details
as well as a test case that demonstrates the failure, see the
referenced PR.
Under certain circumstances involving the persist state, it is
possible for the receive side's tp->rcv_nxt to advance beyond its
tp->rcv_adv. This causes (tp->rcv_adv - tp->rcv_nxt) to become
negative. However, in the code affected by this fix, that difference
was interpreted as an unsigned number by max(). Since it was
negative, it was taken as a huge unsigned number. The effect was
to cause the receiver to believe that its receive window had negative
size, thereby rejecting all received segments including ACKs. As
the test case shows, this led to fruitless retransmissions and
eventually to a dropped connection. Even connections using the
loopback interface could be dropped. The fix substitutes the signed
imax() for the unsigned max() function.
PR: closes kern/3998
Reviewed by: davidg, fenner, wollman
This commit includes the following changes:
1) Old-style (pr_usrreq()) protocols are no longer supported, the compatibility
glue for them is deleted, and the kernel will panic on boot if any are compiled
in.
2) Certain protocol entry points are modified to take a process structure,
so they they can easily tell whether or not it is possible to sleep, and
also to access credentials.
3) SS_PRIV is no more, and with it goes the SO_PRIVSTATE setsockopt()
call. Protocols should use the process pointer they are now passed.
4) The PF_LOCAL and PF_ROUTE families have been updated to use the new
style, as has the `raw' skeleton family.
5) PF_LOCAL sockets now obey the process's umask when creating a socket
in the filesystem.
As a result, LINT is now broken. I'm hoping that some enterprising hacker
with a bit more time will either make the broken bits work (should be
easy for netipx) or dike them out.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
(yes I had tested the hell out of this).
I've also temporarily disabled the code so that it behaves as it previously
did (tail drop's the syns) pending discussion with fenner about some socket
state flags that I don't fully understand.
Submitted by: fenner
callers of it to take advantage of this. This reduces new connection
request overhead in the face of a large number of PCBs in the system.
Thanks to David Filo <filo@yahoo.com> for suggesting this and providing
a sample implementation (which wasn't used, but showed that it could be
done).
Reviewed by: wollman
drop the oldest entry in the queue.
There was a fair bit of discussion as to whether or not the
proper action is to drop a random entry in the queue. It's
my conclusion that a random drop is better than a head drop,
however profiling this section of code (done by John Capo)
shows that a head-drop results in a significant performance
increase.
There are scenarios where a random drop is more appropriate.
If I find one in reality, I'll add the random drop code under
a conditional.
Obtained from: discussions and code done by Vernon Schryver (vjs@sgi.com).
time, in seconds, that state for non-established TCP sessions stays about)
a sysctl modifyable variable.
[part 1 of two commits, I just realized I can't play with the indices as
I was typing this commit message.]
to "keepidle". this should not occur unless the connection has
been established via the 3-way handshake which requires an ACK
Submitted by: jmb
Obtained from: problem discussed in Stevens vol. 3
from Larry Peterson &co. at Arizona:
- Header prediction for ACKs did not exclude Fast Retransmit/Recovery.
- srtt calculation tended to get ``stuck'' and could never decrease
when below 8. It still can't, but the scaling factors are adjusted
so that this artifact does not cause as bad an effect on the RTO
value as it used to.
The paper also points out the incr/8 error that has been long since fixed,
and the problems with ACKing frequency resulting from the use of options
which I suspect to be fixed already as well (as part of the T/TCP work).
Obtained from: Brakmo & Peterson, ``Performance Problems in BSD4.4 TCP''
when a connection enters the ESTBLS state using T/TCP, then window
scaling wasn't properly handled. The fix is twofold.
1) When the 3WHS completes, make sure that we update our window
scaling state variables.
2) When setting the `virtual advertized window', then make sure
that we do not try to offer a window that is larger than the maximum
window without scaling (TCP_MAXWIN).
Reviewed by: davidg
Reported by: Jerry Chen <chen@Ipsilon.COM>
- remove a redundant condition;
- complete all validity checks on segment before calling
soisconnected(so).
Reviewed by: Richard Stevens, davidg, wollman
capacity of the link, even if the route's MTU indicates that we cannot
send that much in their direction. (This might actually make it possible
to test Path MTU discovery in a useful variety of cases.)
or ssthresh that we were able to use
tcp_var.h - declare tcpstat entries for above; declare tcp_{send,recv}space
in_rmx.c - fill in the MTU and pipe sizes with the defaults TCP would have
used anyway in the absence of values here
know better when to cache values in the route, rather than relying on a
heuristic involving sequence numbers that broke when tcp_sendspace
was increased to 16k.
currently considering reducing the TCP fasttimo to 100ms to help improve
things, but this would be done as a seperate step at some point in the
future.
This was done because it was causing some sometimes serious performance
problems with T/TCP.
On Tue, 09 May 1995 04:35:27 PDT, Richard Stevens wrote:
> In tcp_dooptions() under the case TCPOPT_CC there is an assignment
>
> to->to_flag |= TCPOPT_CC;
>
> that should be
>
> to->to_flag |= TOF_CC;
>
> I haven't thought through the ramifications of what's been happening ...
>
> Rich Stevens
Submitted by: rstevens@noao.edu (Richard Stevens)
the lookup fails. Updated callers to deal with this. Call in_pcblookuphash
instead of in_pcblookup() in in_pcbconnect; this improves performance of
UDP output by about 17% in the standard case.
If a goto findpcb occurred during the processing of a segment, the TCP and
IP headers were dropped twice from the mbuf which resulted in data acked
by TCP but not delivered to the user.
Reviewed by: davidg
Bob Braden <braden@isi.edu>.
NB: This has not had David's TCP ACK hack re-integrated. It is not clear
what the correct solution to this problem is, if any. If a better solution
doesn't pop up in response to this message, I'll put David's code back in
(or he's welcome to do so himself).
Several examples of connection initiation follow. Although these
examples do not show connection synchronization using data-carrying
segments, this is perfectly legitimate, so long as the receiving TCP
doesn't deliver the data to the user until it is clear the data is
valid (i.e., the data must be buffered at the receiver until the
connection reaches the ESTABLISHED state).
- Delete redundant declarations.
- Add -Wredundant-declarations to Makefile.i386 so they don't come back.
- Delete sloppy COMMON-style declarations of uninitialized data in
header files.
- Add a few prototypes.
- Clean up warnings resulting from the above.
NB: ioconf.c will still generate a redundant-declaration warning, which
is unavoidable unless somebody volunteers to make `config' smarter.
