This follows NTB subsystem modularization in Linux, tuning it to FreeBSD
native NewBus interfaces. This change allows to support different types
of hardware with different drivers, support multiple NTB instances in a
system, ntb_transport module use for needs other then if_ntb, etc.
Sponsored by: iXsystems, Inc.
Since SBARxSZ register can be write-once, it can be unusable for disabling
the SBAR. For such case also set SBARxBASE to zero to not intersect with
config BAR.
This allows IPv6 link local addresses (and other IPv6 functionality) to work.
PR: 210355
Submitted by: Steve Wahl and David Bright (both at Dell Inc.)
Reviewed by: cem, mav
Tested by: mav (on Intel hardware)
Approved by: re (kib)
MFC after: 5 days
Sponsored by: Dell Inc.
Differential Revision: https://reviews.freebsd.org/D6885
BAR size to 1MB. According to Xeon v3 specifications and my tests, that
size register is write-once and so not writeable after BIOS written it.
Instead of that, make the code work with BAR of any sufficient size,
properly calculating offset within its base. It also simplifies the code.
Discussed with: cem
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
NTB_MSIX_RECEIVED status, before making upper layers overwrite it.
This is not completely perfect, but now it works better then before.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This patch comes from Dave Jiang's Linux tree, davejiang/ntb. It hasn't
been accepted into Linus' tree, so I do not have an authoritative SHA1
to point at. Original commit log:
=====================================================================
A hardware errata causes the NTB to hang when heavy bi-directional
traffic in addition to the usage of BAR0/1 (where the registers reside,
including the doorbell registers to trigger interrupts).
This workaround is only available on Haswell and Broadwell platform.
The workaround is to enable split BAR in the BIOS to allow the 64bit
BAR4 to be split into two 32bit BAR4 and BAR5. The BAR4 shall be pointed
to LAPIC region of the remote host. We will bypass the db mechanism and
directly trigger the MSIX interrupts. The offsets and vectors are
exchanged during transport scratch pad negotiation. The scratch pads are
now overloaded in order to allow the exchange of the information. This
gets around using the doorbell and prevents the lockup with additional
pcode changes in BIOS.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
=====================================================================
Notable changes in the FreeBSD version of this patch:
* The MSIX BAR is configurable, like hw.ntb.b2b_mw_idx (msix_mw_idx).
The Linux version of the patch only uses BAR4.
* MSIX negotiation aborts if the link goes down.
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Replace the hw.ntb.enable_writecombine tunable with
hw.ntb.default_mw_pat. It can be set with several specific numerical
values to select a caching type. Any bogus value is treated as
Uncacheable (UC).
The ntb_mw_set_wc() KPI has removed the restriction that the selected
mode must be one of UC, WC, or WB.
Sponsored by: EMC / Isilon Storage Division
Note that the MW allocation still must be BAR *aligned*. So, this only
loosens the constraints on MW allocation slightly. BAR-aligned does not
play well with large (GB+) BAR sizes.
Going forward, if anyone cares about if_ntb on very large BARs, I
suggest they add functionality to allocate a smaller window than the BAR
size, and set the BAR range to cover a window much larger than the
allocated window. This will require negotiating a window offset and
limit for protocol traffic. None of this is implemented in this
revision.
Sponsored by: EMC / Isilon Storage Division
And expose vm_memattr_t of current mapping to consumers (as well as the
ability to change it to one of UC, WB, WC).
After short discussion with: jhb (but no review)
Sponsored by: EMC / Isilon Storage Division
Adds a new tunable, ntb.hw.b2b_mw_idx, which specifies the offset (from the
total number of memory windows) to use for register access on hardware with
the SDOORBELL_LOCKUP errata. The default is -1, i.e., the last memory
window.
We map BARs before the b2b_mw_idx is selected, so map them all as memory
windows initially. The register memory window should not be write-combined,
so we explicitly disable WC on the selected MW later.
This introduces a layer of abstraction between consumer memory window
indices, which exclude any exclusive errata-workaround BARs, and internal
memory window indices, which include such BARs. An internal routine,
ntb_user_mw_to_idx(), converts the former to the latter. Public APIs have
been updated to use this instead of assuming the exclusive workaround BAR is
the last available MW.
Sponsored by: EMC / Isilon Storage Division
Lower the payload data (IP) portion of the MTU from 0x10000 to
IP_MAXPACKET (0xFFFF) to avoid panicing the IP stack.
Sponsored by: EMC / Isilon Storage Division
This feature is disabled by default. To enable it, tune
hw.if_ntb.enable_xeon_watchdog to non-zero.
If enabled, writes an unused NTB register every second to demonstrate to
a hardware watchdog that the NTB device is still alive. Most machines
with NTB will not need this -- you know who you are.
Sponsored by: EMC / Isilon Storage Division
Discard the unused rx_free_q. Instead, reuse inputed packets by putting
them back on the *pend* queue after reinitialization.
If tx or rx handlers are unavailable, free mbufs rather than leaking
them.
With this change, if_ntb can receive more than 100
(NTB_QP_DEF_NUM_ENTRIES) packets.
Sponsored by: EMC / Isilon Storage Division
32-bit BARs can only address memory mapped in the low 32 bits of
physical RAM. Expose this as a 'plimit' out parameter from
ntb_mw_get_range().
Fix if_ntb to allocate memory within this limit.
Sponsored by: EMC / Isilon Storage Division
Sometimes they'll read spurious values (observed: 0xc on Broadwell-DE),
failing link negotiation.
Discussed with: Dave Jiang, Allen Hubbe
Sponsored by: EMC / Isilon Storage Division
The tunable 'hw.ntb.enable_writecombine' may be set to zero to
administratively disable write combining the mapped NTB region.
Sponsored by: EMC / Isilon Storage Division
Use bus_space_write instead of (non-volatile) C pointer writes via an
iowrite32() shim in the same places as the Dual BSD/GPL Linux driver.
Update some types to fixed 32-bit sizes.
Sponsored by: EMC / Isilon Storage Division
There is no need for the upstream and downstream addresses to be
different for the NTB configs. Go to using a single set of address. It
is still possible to configure them differently using module parameter
override however (CEM: tunable).
Authored by: Dave Jiang <dave.jiang@intel.com>
Reviewed by: Allen Hubbe <Allen.Hubbe@emc.com>
Reviewed by: Jon Mason <jdmason@kudzu.us>
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Order of operations issue with the QP Num and MW count, which would
result in the receive buffer pointer being invalid if there are more
than 1 MW. Corrected with parenthesis to enforce the proper order of
operations.
Reported by: John I. Kading <John.Kading@gd-ms.com>
Reported by: Conrad Meyer <cem@FreeBSD.org>
Authored by: Jon Mason <jdmason@kudzu.us>
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Because it can sleep drainking link work callout(s). Linux (dual
BSD/GPL driver) does something very similar.
At the same time, switch the NTB CTX lock to a non-spin mutex, because
the taskqueue_swi lock can't be taken after a spin mutex.
Suggested by: Witness
Sponsored by: EMC / Isilon Storage Division
In ntb_poll_link, we are intentionally writing the link bit, which is
absent from db_valid_mask. Don't panic on a kassert when we do so.
The Linux version of this (dual BSD/GPL) driver has the db_valid_mask
assertions in callers of db_iowrite() rather than db_iowrite() itself;
it skips the assertions in the equivalent of ntb_poll_link(). Rather
than duplicating the assertions in every caller, add a db_iowrite_raw()
that doesn't check and use it from ntb_poll_link().
Suggested by: kassert_panic
Sponsored by: EMC / Isilon Storage Division
AMD64 pmap assumes ranges will be in the DMAP, which isn't necessarily
true for NTB memory windows (especially 64-bit BARs).
Suggested by: pmap_change_attr_locked -> kassert_panic
Sponsored by: EMC / Isilon Storage Division
This should export all of the same information as the Linux ntb_hw_intel
debugfs info file, but with a bit more structure, in the sysctl tree
rooted at 'dev.ntb_hw.<N>.debug_info'.
Raw registers are marked as OPAQUE because reading them on some hardware
revisions may cause a hard lockup (NTB errata). They can be read with
'sysctl -x dev.ntb_hw.<N>.debug_info.registers'. On Xeon platforms,
some additional registers are available under 'registers.xeon_stats' and
'registers.xeon_hw_err'. They are exported as big-endian values so that
the 'sysctl -x' output is legible.
Shrink the feature mask to 32 bits so we can use the %b formatter in
'debug_info.features'.
Sponsored by: EMC / Isilon Storage Division
Add ntb_q_idx_t so it is more clear which struct members are of the same
type (some bogus uint64_ts snuck in that should have been unsigned int).
Add tx_err_no_buf and s/ENOMEM/EBUSY/ in tx_enqueue to match Linux.
Sponsored by: EMC / Isilon Storage Division
A plain 32 bit integer will overflow for values over 4GiB.
Change the plain integer size to the appropriate size type in
ntb_set_mw. Change the type of the size parameter and two local
variables used for size.
Even if there is no overflow, a size of zero is invalid here.
Authored by: Allen Hubbe
Reported by: Juyoung Jung
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
It was possible for a synchronous update of the RX index in the error
case to get ahead of the asynchronous RX index update in the normal
case. Change the RX processing to preserve an RX completion order.
There were two error cases. First, if a buffer is not present to
receive data, there would be no queue entry to preserve the RX
completion order. Instead of dropping the RX frame, leave the RX frame
in the ring. Schedule RX processing when RX entries are enqueued, in
case there are RX frames waiting in the ring to be received.
Second, if a buffer is too small to receive data, drop the frame in the
ring, mark the RX entry as done, and indicate the error in the RX entry
length. Check for a negative length in the receive callback in
ntb_netdev, and count occurrences as rx_length_errors.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Mechanically replace "SOC" with "ATOM" to match Linux. No functional
change. Original Linux commit log follows:
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Prints driver name to indicate what is being loaded.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Throw away the result of the peer SPAD read. The peer will write our
local SPAD and we need to keep the locally read SPAD value to check if
the remote side is up.
Sponsored by: EMC / Isilon Storage Division
Add module parameters for the addresses to be used in B2B topology.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
We skip actually bringing up Rootport/Transparent configurations, so
most of this doesn't apply. Original Linux commit log:
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
It is just a trivial wrapper around ntb_mw_set_trans().
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This is the last e26a5843 patch. The general thrust of the rewrite was
to move more responsibility for Memory Window and Doorbell interrupt
management from the ntb_hw driver to if_ntb.
A number of APIs have been added, removed, or replaced. The old
DB callback mechanism has been excised. Instead, callers (if_ntb) are
responsible for configuring MWs and handling their interrupts more
directly.
This adds a tunable, hw.ntb.max_mw_size, allowing users to limit the
size of memory windows used by if_ntb (identical to the Linux modparam
of the same name).
Despite attempts to keep mechanical name changes to separate commits,
some have snuck in here. At least the driver should be much more
similar to the latest Linux one now -- making porting fixes easier.
Authored by: Allen Hubbe
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change. Part of the huge rewrite (e26a5843).
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Move all Xeon secondary register setup to the setup_b2b_mw routine. We
use subroutines to make it a bit less wordy than the Linux version.
Adds a new tunable, 'hw.ntb.b2b_mw_share'. By default, it is off
(zero). If both sides enable it (any non-zero value), the NTB driver
attempts to use only half of a memory window for remote register MMIO
access.
This is still part of the large Linux rewrite (e26a5843).
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This Linux commit was more or less a rewrite. Unfortunately, the commit
log does not give a lot of context for the rewrite. I have tried to
faithfully follow the changes made upstream, including matching function
names where possible, while churning the FreeBSD driver as little as
possible.
This is the bulk of the rewrite. There are two groups of changes to
follow in separate commits: fleshing out the rest of the changes to
xeon_setup_b2b_mw(), and some changes to if_ntb.
Yes, this is a big patch (3 files changed, 416 insertions(+), 237
deletions(-)), but the Linux patch was 13 files changed, 2,589
additions(+) and 2,195 deletions(-).
Original Linux commit log:
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Authored by: Allen Hubbe
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Some interrupt-related function names changed to match Linux.
No functional change. Still part of the huge e26a5843 rewrite in Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
No functional change.
Still part of the huge e26a5843 rewrite. I'm trying to make it less of
a complete rewrite in the FreeBSD version of the driver. Still, it
helps if our names match Linux.
Obtained from: Linux (e26a5843) (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
On the Haswell platform, a split BAR option to allow creation of 2 32bit
BARs (4 and 5) from the 64bit BAR 4. Adding support for this new option.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This is a follow-up to r289208: "Xeon Errata Workaround."
Add logic to support a variable number of memory windows and doorbell
callbacks. This was added to the Linux driver in the "Xeon Errata
Workaround" commit, but I skipped it because it didn't look neccessary
at the time. It is needed for future Haswell split-BAR support, so
bring it in now.
A new tunable was added for if_ntb, 'hw.ntb.max_num_clients'. By
default, it is set to zero -- infer the number of clients from the
number of memory windows available from the hardware. Any other
positive value can specify a different number of clients, limited by the
number of doorbell callbacks available (4 under MSI-X, or 15 (Xeon) or
34 (SoC) under legacy INTx).
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Pull out read of PPD and platform detection logic to new functions,
ntb_detect_xeon(), ntb_detect_soc(). No functional change -- mostly
this is just shuffling the code to more closely match the Linux driver.
Linux commit log:
To simplify some of the platform detection code. Move the platform
detection to a function to be called earlier.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The doorbell registers (and associated mask) are 16-bit on Xeon but
64-bit on SoC. Abstract IO access to doorbell registers with
'db_ioread' and 'db_iowrite' (names and idea borrowed from the dual
BSD/GPL Linux driver).
Sponsored by: EMC / Isilon Storage Division
Original Linux commit log:
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Remap MSI-X messages over available slots rather than falling back to
legacy INTx when fewer MSI-X slots are available than were requested.
N.B. the Linux driver does *not* do this.
To aid in testing, a tunable 'hw.ntb.force_remap_mode' has been added.
It defaults to off (0). When the tunable is enabled and sufficient
slots were available, the driver restricts the number of slots by one
and remaps the MSI-X messages over the remaining slots.
In case this is actually not okay (as I don't yet have access to this
hardware to test), a tunable 'hw.ntb.prefer_intx_to_remap' has been
added. It defaults to off (0). When the tunable is enabled and fewer
slots are available than requested, fall back to legacy INTx mode rather
than attempting to remap MSI-X messages.
Suggested by: jhb
Reviewed by: jhb (earlier version)
Sponsored by: EMC / Isilon Storage Division
Consumers that registered on this bit would never see a callback and it
is likely a mistake.
This does not affect if_ntb, which limits itself to a single doorbell
callback.
The names don't line up 100% with Linux. Our routines are named
ntb_setup_interrupts, ntb_setup_xeon_msix, ntb_setup_soc_msix, and
ntb_setup_legacy_interrupt. Linux SNB = FreeBSD Xeon; Linux BWD =
FreeBSD SOC. Original Linux commit log:
This is an cleanup effort to make ntb_setup_msix() more readable - use
ntb_setup_bwd_msix() to init MSI-Xs on BWD hardware and
ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the way it should
has been done - looping pci_enable_msix() until success or failure.
Authored by: Alexander Gordeev
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Provide a better event interface between the client and transport.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs. Previously, Snoop was only enabled from Secondary to Primary
side. This can have a performance improvement on some workloads.
Also, make the code more obvious about how the link is being enabled.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Add a comment describing the necessary ordering of modifications to the
NTB Limit and Base registers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active. This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated. To correct this, shutdown the qp's prior to bringing
the transport link down. Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt. Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue. To get around
the issue, shrink the number of available doorbell bits by 1. The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit. Since this would no longer work, the driver must now
explicitly reference that bit.
This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
NTB-RP is not a supported configuration on BWD hardware. Remove the
code attempting to set it up.
Authored by: Jon Mason
Obtained from: Linux (dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
